Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

When using dyson in upright possition does not pick up very well. roller is going round. when you press front to begin hoovering carpets the front doesnt seem to drop onto floor low enough. dont think suction pipe is engaging properly !!!!!!.

Answers :

Hi Peter,

I'm sorry to hear you're having difficulties with your DC07. It sounds as if the internal hose may have become twisted - you should be able to resolve this by removing and replacing it as shown in the video below. Please make sure the hose isn't damaged, and take care not to over-tighten it when you replace it.

If you continue to experience difficulty after doing this, please get in touch with us directly, as one of our advisors will be happy to provide further assistance. You can reach us on 0800 298 0298 - our Helpline is available from 7am until 10pm, 7 days a week.

Best wishes,

Dyson Online Customer Support

Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

When using dyson in upright possition does not pick up very well. roller is going round. when you press front to begin hoovering carpets the front doesnt seem to drop onto floor low enough. dont think suction pipe is engaging properly !!!!!!.

Hi Peter, I'm sorry to hear you're having difficulties with your DC07. It sounds as if the internal hose may have become twisted - you should be able to resolve this by removing and replacing it as shown in the video below. Please make sure t ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My son dropped the vacuum down the stairs and now the vacuum works but the front part of the vacuum does not drop back down when vacuuming any type of floor. It slowly drops and does not stay on the carpet. hope this makes sense. I have cleaned filters and suction seems strong at the small hose. the beater bar rotate very fast still.

May be part missing. this is unit has 5-year warranty.you can send to service. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Put in new clutch, but the brush does not seem to be lowering when you change between bare floor and carpet. Does not seem to be touching carpet when engaged. Still has good suction.

The brushroll must be broken ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Dyson vacuum I have a DC07 vaccuum. The problem I am having is that the front does not want to stay down as I vaccuum and I continuously have to keep stepping on the front to make it go back down to the floor. It seems as though there is either not enough weight in the front or possibly the unit just has to be broken in so that there is not so much resistance between the handle and the front of the vaccuum. Could there be something I did not remove or is this typical on these vaccuums?

There is some thing broken it is two plastic cogs they help the front go down and stay up you will have to get a star screw driver and there should be two screws on top and two at the b ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Roller Brush How do I install the roller brush. I didn't pay attention when I removed it and now when I attempt to vacuum my low carpet it doesn't seem to be working. The green light on the head of the vacuum goes out when I click it down to the floor. It didn't used to do that. Plus I think I smell something burning. Could the belt be broken?

Try a new belt. The ends of the brushroller are different sizes, so you can't put it in backwards. There are numbers and notches on the ends of the brushroll. These notches/numbers need to match on both sides when installing it. (probably need b ... Kirby Ultimate G Bagged Upright Vacuum

I have a Eureka "The Boss" vacuum that doesnt seem to be sucking up as much as it should and did in the past when vacuuming on carpet and hard floor surfaces.

I have a Eureka "The Boss" vacuum that doesn’t seem to be sucking up as much as it should and did in the past when vacuuming on carpet and hard floor surfaces.\015\012 \015\012I woul ... Vacuums

I have a Dyson all-floor model (not the ball). I recently replaced my carpet to a Frieze. Since replacing the carpet, the Dyson is extremely hard to push. It almost forms a "seal" with the carpet. Seems to work fine on Berber carpet and laminate floor. My husband has checked to make sure the brushes are working, hoses are not clogged and belts are OK. I've had it for about a year. It is virutally impossible to push on the new carpet. Any ideas?

Have you adjusted the brush control system. If you look at the link below page 6 will tell you how to adjust. If this is not you vacuum please give the model # of the one you have so I can help you more.\015\012\015\012 ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Just got my dc33... one issue... the dial switch to control btn bare floor / carpet mode doesn't seem holding in it's position when I set to the bare floor mode... it keeps coming back to carpet mode with brush-bar activated... the dial doesn't really click to the floor mode. Any advice on this?

Hi there,I'm sorry to hear you're having difficulties with your DC33. If you're concerned that the brush control doesn't seem to be staying in position, it's probably best if you get in touch with us directly. One of our experts will be h ... Dyson DC33 Bagged Upright Vacuum

When i set it on carpet instead of bare floor it is hard to push when i vacume (when i turn nob it only has two settings floor and carpet no high pile or low pile)

Hi there,Sorry to hear you're having difficulties using your DC14 on this particular carpet. You may want to contact your carpet manufacturer to check it's suitable for cleaning with a vacuum cleaner equipped with a revolving brush. Manuf ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Why does my Oreck drag on carpeting? bought an Oreck upright 4.8 bagless at a garage sale. Great on the kitchen floor but seems to drag , difficult to push on the commercial carpeting. any hints

... Oreck Dual Power Electric Floor Sweeper Bagless Upright Vacuum

I have an electrolux renaisence vacuum. the brush in the floor attachment turns but I have no suction. When I change to bare floor option on the handle the brush stops turning (correct) but I still have no suction. The lights on the handle showing --floor,carpet, high and low all work.

Sounds like you have a clog, either in the hose or the inlet by the brush roll. ... Vacuums

On our new carpet (which is not that thick but thicker than the old) I can't set the carpet thickness high enough. The suction really grabs the carpet and bogs down my self-propelled wind-tunnel Hoover. I then have to push down on the handle to tilt the front up. The thickness setting is as high as it will go. Is there some way that I can further adjust this. The machine is about eight years old.

I can help you out only if you will let me know the front width of the machine. Alongwith the height which you wan't to give raise. KIndly give the width and elevation in cms. ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Dirt devil vacuum cleaner--trouble vacuuming dirt and pet hair on carpeting --is the problem with the spinning brush which contacts the floor,  not contacting the carpeting??  I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting.  Sometimes, it seems like nothing is being vacuumed up --unless I have just put a new bag on the vacuum... Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums

Try replacing the belt. Rubber belts stretch out after about a year. ... Dirt Devil CE6100 Featherlite Upright Vacuum

How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a

The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My steam-vac carpet cleaner doesnt seem to be pulling the dirty water back out of the carpet.

The most common reason for this is that the lid is not fully seated on the dirty water tank. Be sure to hook the lid in front, and then snap it in place at the rear. Another problem could be that the duct is missing from the front of the tank. ... Hoover Vacuums

We have two of these vacuums and both of them have experienced the same problems. First the floor heighth adjustment doesn't work and now neither one will pick up on either carpet or floor when in the brush/floor mode. They both seem to work with the suction hose function. We have removed the back panel to see if there was an obstruction but it was clear. We have changed the bag and the small filter (not the HEPA filter) all to no avail. What else can we do? We are desperate to use our vacu

Did you check the powerhead for obstructions? With a bend in the tube just below where the hose connects, this is a common spot for clogs. To check, detach hose and drop a coin in the hole. If it doesn't drop through, a blockage is present. Use t ... Electrolux Oxygen 3 Upright Vacuum Cleaner - EL5035 Vacuum

Does the epic 3500 have a belt? It seems that when running on the carpet setting, it is very noisy and is not picking up the way it should. When we run it on the floor setting, it sounds better, but the rolloer doesn't go around to fluff the carpet. What is wrong?

Yes, it does. It definitely sounds like a broken belt. And the noise would probably be due to the belt still being in the machine and hitting the motor shaft.\015\012Due to some difficulty in reassembling the powerhead and getting the belt to ... Electrolux Epic 3500 Vacuum

My Dyson is not picking up on the carpet as good as it use to. The brush doesn't seem to engage on the carpet unless I hold the angle upright. It's very uncomfortable to hold it at that angle. What would correct this problem?

Brushes do wear out. Compare the length of the bristles on you brush with a new one. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My eureka optima upright bagless vaccum has VERY low suction using the floor part. the hose has excellent suction. i removed the little translucent door underneath and there were no blockages, i cleaned the brushroll thoroughly and that hasnt helped either. i know this probably isnt recommended but i turned it on to the floor setting with the brushroll off and stuck my fingers up the intake as far as i could, the suction was good further up but it just seems to stop down at the base. because i s

I will try and help here. Is the sole plate on the bottom of the vacuum complety on and there are no visible cracks along the seam where it meets the body? This is the usual cause for this. Onc you take of the plate to access the roller and brushes, ... Eureka 431A Optima Bagless Upright Vacuum

Windtunnel U6425-900 It seems the vacuum gets stuck in the carpet when the front dips and sucks up the carpet.

I think I may have the solution to all these same problems: If you buy a new front brush this might solve your problems, because the brushes have worn down and causing the vacuum to **** stronger because it is closer to the carpet. I hacve the same ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My dyson 07 doesnt **** up when im doing the carpet but the hose works fine? when im vacuming it sucks up very little and the hose part seems to be sucking up air when im doing the carpet? would this mean something is plug??? thanks randy

There is a block in the hose take lower hose of and clean ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I want to brush the pile up on my carpet do I need a special attachment to do this??. I have shampood it and it still seems a bit flat. When I shampood no water/foam filled up in the front tray???I am sure I had attached everything correctly. The only thing I can think of is when I attach the brush and tray to the front of the machine, do I turn the handle back to the right way up, or do I leave it upside down, this is the one that picks up the belt.

Here's my online guide for using the Kirby shampooer....\015\012\015\012 ... Kirby Ultimate G Bagged Upright Vacuum

My Bissell proheat 2x model 9200 is not dispensing cleaning solution. I hold the trigger and the carpet doesnt get wet at all. i poured water on the carpet and it sucks it up. the cleaning solution does mix with the water but it not being dispensed on the floor.

Hi, \015\012when last did you service the machine?\015\012\015\012i believe should service the machine.\015\012try to open the machine.\015\012\015\012when opening make sure you notice where the part you are remov ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

While using, steam stopped coming out in force at the port levels in the head. Suddenly started high pitch whining, pressed button just above connection site and end flew off with great force pouring water onto floor and carpet. Unplugged immediately for safety and unable to get it to deliver steam force again. Less than one year old and used only 8-10 times only in walk areas where there is no carpet with distilled water. Please, advise, cannot find booklet. Thanks So Much, Beverly Crumme

Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it may not be getting steam to the head...Euro ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

I have a Kirby G4 Vacuum Cleaner - MOdel G4 D. I have never had any problems or repairs done to it in the past ten plus years that I've had it. This is an upright vacuum. I was vacuuming the carpet floor and was not having any trouble at all. I switched the vacuum off and moved it into a different room. When I tried to turn on the vacuum, it would not turn on. I checked with different outlets, used both front attachment and hose attachment. Checked the front part of the motor/ spiral case. This

Hello,\015\012My educated guess is that it's either the switch or the power cord. Here are a couple of guides to help with diagnosis and repair...\015\012\015\012 ... Kirby G4 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0663 seconds