Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?
Vacuum turned off started smelling and got hot but only for 2 to 3 minutes then turned off
Hi There, 2 to 3 minutes is too short for a blockage in my opinion. I would suggest you have a burnt out motor. Did it make any kind of uneven sound or popping sound? If yes then you will need to replace the motor. There are a couple of good videos on youtube to help you out if you are suitably qualified or skilled. This is a pretty tricky repair though I would give it a 7/10 for difficulty.
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Vacuum turned off started smelling and got hot but only for 2 to 3 minutes then turned off
Hi There, 2 to 3 minutes is too short for a blockage in my opinion. I would suggest you have a burnt out motor. Did it make any kind of uneven sound or popping sound? If yes then you will need to ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Vacuum started smoking and smelled. Yikes! I new it was the belt. Got a new belt replaced it.... with less than a minute it burned up another. The rotor/ pin that the belt goes around that should be spinning right? What do i do to get it to spin?
... Dirt Devil M084600 Dynamite Bagless Upright Vacuum
I have a Eureka Power Plus vacuum, model 4702, type A. To start off, it never really had great suction. Marginal at best. Then today I was vacuuming and smelled something burning and turned off the vacuum. At that point, smoke started pouring out from the bottom of the vacuum so I layed it on it's side and the smoke cleared but I never found the source. Is it safe to turn on again after I let it cool down or is my vacuum "shot?"
The breaker on the vacuum trips after about 3 seconds on. The canister was extremely full and started to smell like burnt wood, we fully cleaned out the unit. Now when the vacuum is turned on, the motor sounds weak, and then turns off in a matter of seconds,and we have to reset the breaker on the vacuum to get it to start again for another few seconds.
This sounds indicative of a worn set of carbon brushes on a dieing motor for a central vac. the armature is ,likely damaged causing teh breaker to blow. Please post back with more details as to make and model. Do not atempt to run the vac ... Vacuums
Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would "heave" (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won't turn. Any suggestio
Carpet brush won't turn when vac on ... Euro-Pro NV31 Infinity Vacuum
Vacuum smell I have a new bagless Hoover Empower Widepath. When I start to vacuum, after only about 2 minutes, it starts to smell really bad, like rubber I would say. Is it band slipping, and how do I check that out to make sure??
Your belt is slipping, it is probably stretched and slips trying to drive the brush roll. Take the bottom plate off, check the brush also, make sure the ends turn freely. The belt runs from the brush roll to the motor shaft. If you can't get to th ... Vacuums
Won't start. My son was using the vacuum & Didn't change the bag. The vacuum was making the full bag smell, but the light was't on & it didn't stop. I stopped him, changed the bag, checked the filter, closed the compartments & turned on the vacuum. Nothing happened. I checked to be sure that it was plugged in, that wasn't the problem. I've let the vacuum "rest" for several days, It still won't start. Any suggestions?
There is a reset button at the back of the powerhead. The user manual can be downloaded from the electrolux website, although I didn't find it very useful. There was some info on how to change the powerhead drive belt. ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum
I heard that a class action lawsuit against Oreck Vacuum is being started because of all the problems customers are having with their vacuums. Does anyone know about this? My Oreck is only a couple of years old and keeps burning up belts. I took it in after only one week of usage when I started to notice white smoke coming out of it and the smell of burning rubber. I feel like I got the old run-around, when the service tech told me he couldn't find anything wrong (but replaced the burned up belt
You are correct about the fact that legal action has been taken. Go to this link to read more\015\012\015\012 ... Oreck XL2200 Bagged Upright Vacuum
My Dirt Devil Vibe bagless vacuum started giving off a burning smell. The brush roller was jammed with hair. I immediately shut it off and cut the hair out of the rollers with scissors until it turned freely. When I turned it back on, the smell was gone but there's no suction now. Did I ruin the belt or something else?
It's more likely there's a clog in the hose somewhere, possibly where it connects to the power nozzle. Detach hose and check the PN. \015\012If there's no clog in the PN, detach hose completely from machine and try to drop a marble or coin th ... Windsor SR12 Sensor Bagged Upright Vacuum
I have the eureka capture vacuum and it works great; however, it has recently started making an extremely high pitched sound when I use it. It is still vacuuming but the noise is so loud it hurts my head and I can only vacuum for a few minutes at a time before I have to turn it off. What is wrong with it???
Dust is getting past the dust cup filter, to the motor. Call Eureka customer service. 1-800-282-2886. ... Eureka 12 Amp Capture Vacuum Upright Vacuum
When I turned on the vacuum it started to smell
You did not say if the vacuum ran and started to stink after running for a while. If this is the case, it's usually time for new brushes and a motor cleanup. ... Rainbow Vacuums
Smoking belt Hey I have a Eureka 2961 avz bagless vacuum, and if it's on for a few minutes i can smell the belt burning. If the vacuum is left on any longer the belt starts smoking. I took the case off and there was a little debris but not much. Is there a cause and fix or just time to replace the belt?
Belt is slipping because the bearings on the beater brushes, which it turns, are jammed or full of dust. \015\012Alternatively the belt has stretched after being overheated and needs replacing because it now slips. ... Eureka 2961AVZ Bagless Upright Vacuum
VACUUM ONLY WORKS FOR 45 SECONDS THEN TURN OFF ITSELF. I HAVE TO WAIT FOR 10-15 MINUTES TO START AGAIN USING IT, STOP WORKING AGAIN AFTER 45 SECONDS. VACUUM IS NEW, I COULDN'T RETURN IT TO THE STORE I BOUGHT IT. PLEASE HELP ME TO RESOLVE THIS PROBLEM. THANKS
Sounds like it overheats quickly. But why are you not able to return it? ... Hoover U5750-900 WindTunnel Bagless Upright Vacuum
I have a kirby sentria. vacuumed up my son's headphones and immediately shut if off. took brush off, unwound headphones, put it back together. when i turned it back on, the belt snapped. so i went to vacuum place, got new belt, but when i put it on, with the green arrows lined up, it doesn't have much suction. with the red arrows lined up, it just smells like its burning and i don't want to break another belt! HELP!!
Take the front off the vacuum and check inside both the front portion and the canister for additonal clogs. Sometimes something will get caught in the impellor, causing the motor to overheat. Since there's little suction and the smell, I'd guess th ... Kirby Generation 3 Bagged Upright Vacuum
I just used my Bissell Proheat, when I heard the vacuum sound get lower and lower then suddenly something "gave" and it got very loud and started emitting a burnt rubber smell. It still worked to put liquid into the carpet; seemed to have trouble getting it out. I checked the tank, filters, belt, and roller and all seemed OK - but when I started up again and looked down I saw sparks in the motor/belt area and shut it down immediately. Any thoughts?
The bearing that is located at the top of the vacuum motor has failed . Because of that the shaft of the motor's rotor is out of position and the pulley attached to it has started rubbing on the other pulleys, giving you that smell. the spark appear ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
Have a Centralux Aerus about 5 years old. Don't see a model number. There is suction but beater brush quit working. Was using for a few minutes, shut it off for a few minutes, turned it back on and suction only. Tried the reset button also. Tried the sidekick attachment and it works fine. There was no smell like something was hot. Belt is fine. Are there any fuses or anything else to try? This vacuum cleaner has not really been used that much, it is hard to believe the motor would need replaced
There probably is a loose wire in the handle near the switch or a wire off near the swivel elbow near the vac power head. With the right fastener tool to remove some screws you can fix it yourself ... Electrolux Centralux Vacuum
Terrible noise My dyson was working great then started making this horrible noise. I cleaned the bar but noise is still there. I discovered the beater bar went around three passes then froze and started horrible noise again. my husband got the bar turning but after 2 swipes vacuuming it did it again. Can it be fixed or is it time to retire it and buy a new one. Wendy Kiser
That noise is the clutch. A very expensive part and very hard to replace. When a problem with the clutch happens it's generally not worth the time and money to replace.I suggest getting a different type of vacuum, maybe a Miele or Sebo. W ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
I have had my Bissell Healthy Home for just over a year. I use it once or twice a week on five area rugs and two small bedrooms with wall to wall carpet. Just recently, the motor started to sound extremely loud and it smells like it's burning. The vacuum still picks up everything and all the brushes are turning. Advice? I really like this vacuum and would really like to fix it rather than replace it!
Hi,Here is a tip that I wrote about my Bissel but I bet you have the same problem and the hose is clogged...Bissell Bagless Upright Vacuum no ... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum
I have a dyson canniter stow away vacuum. i've had it for 2 years and it just started having a problem. when i turn it on the motor starts just fine but the vacuum head does not turn on. Yet when i push it forward it trys to start and turns on for a second and turn off - almost like the connector isn't connecting the hose to the head very well anymore.
Hi, After reading you're problem, the symptom's are just like you said. Its just a matter of checking the connections. The connection where it plugs into the head it self. When you push forward the forward motion and down pressure makes ... Dyson "Stowaway" Canister Vacuum Vacuum
I have a windtunnel vacuum that the brush rolls fine when it is upside down but when I turn it right side up it will not go hardly at all and starts to smell hot.
Replace the belt they wear manufacture reccomends replacement of the belt every 90 days ... Vacuums
I have owned my kirby sentria for 2.5 years and have had no problems until now. The vacuum still works but I cannot lower it all the way down or the light will turn off and it will start to smell like something is burning inside. I use it on the 2nd or 3rd setting with no problem. I have changed the belt and cleaned all the hair and strings that were on the roller but it still has this problem.
Kirby has a 3 yr back to base guarentee so contact ur local rep or kirby direct and thy will sort it all from there, hope this helps :) ... Kirby Vacuums
After a few minutes of using my vacume it starts to smell like burnt rubber. like the belt is burningthe only belt I can see looks fine and is turning the brush
But how tight is the belt and how easy is the brush to turn? if the belt is slopy it will slip on the motor drive spindle,,,and it will get very hot then,,, also if the brush head is tight that makes the belt slip too, ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum
My eureka vacuum won't suction and starts to smoke when I try to use it. It sounds like it is suctioning when I first turn it on, but after about 20 seconds it begins to smell like burning and does not suction at all. I have tried cleaning and unclogging the filter and everything. It's bagless so I don't need a new bag.
The problem is that your belt is stretched and worn. This causes that burning smell and it also causes the vacuum to not pick up well. You need to replace the belt. Here is the belt you need and the manual with instructions: ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum
I have a 10 year old AirVac central vacuum system that has worked until this morning. As I was using it this morning, and turned it off for about five minutes it would not start again. The tank in the garage (that accepts the dust) sounds like it is just huming not working. What is wrong?
Sounds like the motor finally siezed on you. Motor is trying to turn but won't thus the hum. Do not allow the vacuum to stay on like this as it may cause a fire. Requires a motor replacement. ... M&S Systems ZX7000 Bagged Central System Vacuum
Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the
... Dirt Devil M088905 Vision Bagless Upright Vacuum