Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

Dc07 when vacuuming motor and roller part will not stay on floor , as you pull and push the vacuum the brushes keep lifting up and I have to push it down onto the floor how do I fix this?

\015 Roller will not stay on floor , is this a lubrication problem if so what do I and how do I do it?\015

Answers :

Most dc o7 do require a little wd40 at the hinges however if problem isn't fixed try looking and making sure all the peices are snapped in like they're supposed to be. hope this helps
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dc07 when vacuuming motor and roller part will not stay on floor , as you pull and push the vacuum the brushes keep lifting up and I have to push it down onto the floor how do I fix this?


Most dc o7 do require a little wd40 at the hinges however if problem isn't fixed try looking and making sure all the peices are snapped in like they're supposed to be. hope this helps ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I took the hose off to wash it then after letting it dry overnight I put it back on but Im guessing it there was still a little bit of water in between the grooves which ran to bottom of vacuum and now my dyson gets stuck, sort of like a tight hinge. It vacuums fine but I have to keep pushing it down to the carpet with my foot. How can I fix this problem?


Lubrication at the pivot points ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Bissell lift off vacuum about 4yrs old. Extremely noisy. OK until before Christmas but getting worse every time it's used. Washable filters washed, HEPA filter replaced. brush bar cleaned of every scrap, hose empty,everything that can be cleared has been. Noise high pitched, screeching and can only bear to use it for a few seconds at a time. Suction OK. Mine is so loud I can't use it very long-high pitch screech. Can this be fixed or does the whole vacuum need to be replaced? It still cleans gr


Sounds like a bad motor. Could be either foot motor or main motor either way cost will be more than half of the unit. ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

We have a Bissell Revolution Lift-Off Turbo 3760-1 and the upright brush is not working/rolling. It only moves when pushing the vacuum. We checked the belt and it seems to be fine. The vacuum works fine as a hand-held. Any suggestions? Thanks!


These belts need to be changed every 6 months regardless of the way they look. ... Vacuums

My Dyson DC24 sucked in a backpack strap and tripped. I then decided to pull out the brush and clean off whatever else happened to be clung onto it and put it back in. The darn thing doesn't turn anymore. Everyone says to push the reset button in until a click is heard but I put in a bit of force and I haven't heard a click so I stopped because I didn't want to break it. Is there something I haven't checked or do I keep adding force?


If the motor is running and the roller is not turning you may have to let the handle down as you would when you are getting ready to vacuum the flood. I think there is a switch you step on to let the handle down and it will engage the roller bar moto ... Dyson Ball DC24 Bagless Upright Vacuum

Hello. My dyson dc04 keeps making a loud screeching noise when im vacuuming. It seems as though the plastic from the brush is catching on the plastic on its holder either side of the belt. Is there any way of fixing this problem?


Remove base cover by 3 'screws' 1/2 turn anti clockwise and clean well remove fibres replace cover and re try. ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I have a self propelled Royal Dirt Devil vacuum model number 087900 and it goes backward fine but forward has to be pushed so hard it's impossible. Is this a switch? Do you know about how much the part would cost and can it be done by a beginner. We fix a lot of things ourselves but we aren't mechanics by no means. We put a brand new belt on it. I don't think it can be put on backwards and brush turns fine. Where is the switch? Use layman's terms.


You might try a new belt and/or brush roll. The brush roll is what helps pull a vacuum forward, the power drive helps, but if the brush isn't turning like it should, then it will hinder forward motion. The belt may look ok, but they stretch to the ... Vacuums

Kenmore upright vacuum belt keeps breaking as soon as I put a new one on. I have made sure the brush roller is clean. How can I fix this or troubleshoot this?


... Kenmore 31723 Vacuum

My hoover Wind Tunnel vacuum cleaner's motor spindle keeps overheating. Because of the high temperature, it keeps burning through belts (the big, wide ones). I have taken it in to the vacuum repair shop about three times now, and the problem has never been fixed. Does anyone have any advice on how to fix this or should I just buy a new vacuum?


... Vacuums

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula


There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

My Kenmore 35922 works well on floors, but it recently became very difficult to push on carpet. The brush spins and a local vacuum repair guy wouldn't solve my problem since the vacuum worked fine on his very flat, commercial carpet. What can I do to get my easy to push vacuum back?


Hi dalee196,There are three common reasons why vacuum cleaners are getting hard to push.1. Base is dirty - The base needs to be clean from dirt and tar.2. Height is too low - You might want to consider adjusting th ... Vacuums

I have a Bissell Lift-off Revolution Turbo vacuum and the brush doesn't spin on its own anymore. Does this mean the motor is busted because there's no noise when you press the brush button. We've just replaced the belt, hepa filter and a new brush. But its still the same. What's wrong with my vacuum?


Its probably the motor. remove the covers with a #2 phillips head screwdriver and cut the wires to the motor ( unplugged ). purchase some crimps at radio shack to resplice the wires together in the same fashion. ... Bissell Vacuums

4870 Boss Smartvac. The vacuum tipped over and now the brush control lever will not stay in the carpet position. I can't get the brush to turn unless I push down and hold the lever. As soon as I let up on the lever the brush stops turning. Any ideas. The vacuum is only a month old.


The Boss has a slide lever on the top of the power nozzle with two position choices. One position is "Carpet" and the other is "hard/bare Floor". The power nozzle brush roll is activated when the lever is in the Carpet position, and it is t ... Eureka Smartvac 4870 Bagged Upright Vacuum

When I push my vacuum with the rotary brush on carpet the rotary brush head shakes. It's fine when I pull it back. I just can't push it.


It may be time to replace the belt on the unit. sometimes when the belt slips (not broken yet) it will give you the same effect. It will also sound a little sluggish too. replace the belt and you should be ok for 1 year. if your using the unit more t ... Rainbow E series Canister Wet/Dry Vacuum

Power Problem Whenver I push the power button on the handle the vacuum stays on for a few seconds then turns off. I have to push the button on the handle all the time to keep the vacuum working.


Hi There,\015\012\015\012Unfortunately this is being caused by static electricity building up in the electronic controls in the handle of the hose. I've seen this problem on numerious occasions, and in fact I have the twin brother of t ... Miele Blue Moon Bagged Canister Vacuum

Brush roll belt stops turning when in position to vacuum. Does turn when vacuum is turned onto side. Belt is in tact, brush roll is fine. What's going on?


I think I know what the problem is with your machine. It's a rather lengthy repair, and I'll be happy to photograph it for you (like I do on most of my Fixya answers), but I'd like to know before doing all of that if you still need help, or if you' ... Eureka Smartvac 4870 Bagged Upright Vacuum

Miele s7000 I first got the vacuum and used it for 20mins then the vacuum just lost the suction, the brush works but it just push the dirt around the house and I can see the dust and dirt flying around.So, I thought maybe the bag was fulled so I put the new bag in but still pushing the dirt around. What's wrong with it?


... Vacuums

Brush is not engaging when vacuuming. If lifted


Therre are usually aprings that hold the brush in position or a spacer thaqt turns when you adjust the height. turn the vacuum over and remove the plate covering verything. make sure your unplugged first. it usually takes about 5-6 phillips head scre ... Hoover Tempo Widepath Upright Vacuum - Blue

Our vacuum will not stay running.. We have cleaned both filters several times since dyson told us there was a switch which turns the vacuum off if the filter in the ball was dirty, but we still need to keep pushing the switch several times to turn the unit back on while vacuuming.


... Dyson DC25 All Floors Bagless Upright Vacuum

My dyson won't stay on. I push the red power button and it begins to start but as soon as I stop pushing it, it stops. It will only work if I keep pushing down the start button the whole time I'm using it. HELP!!! I love my vacuum!


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.


... Hoover Tempo Widepath Upright Vacuum - Blue

Dc07 problem I have a dc07 cyclonic vaccum and like this model,however, for some reason,it has been very dificult to push and pull for the past month or so. i have completely cleaned the brush assembly,cleared any obstructions in the hoses,and, cleaned the filter.I also checked the belt tension,wich i thought was fine but to no avail.Be advised that the brush assembly is spinning and suction is excellent. It just feels like the brush drags along the carpeting. this is a great vacuum cleaner and


The dyson uses two belts, one from the motor to a clutch and then from the clutch to the brush roller, the belts that they use are not much better then any other belt ( those you should change yearly ) but you cant just change the belts you have to c ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu


This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

Suction Problem I was vacuuming and stopped to empty the cannister. When I started vacuuming again - the suction wasn't working properly. The vacuum was just pushing stuff around the floor. I cleaned the hair out the brush on the bottom and it still isn't working. It was working fine before I emptied the tube :( I can't figure out what happened.Help!


Greetings from GoVacuum,\015\012\015\012I believe what may have happened is that your vacuum cleaner belt has either broken, or been stretched so far that ithe brushes are no longer spinning fast enough. \015\012\015\012Here' ... Vacuums

I am trying to replace my vacuum belt and can not get the roller brush to fit back into the slot after I put the belt back onto one end of the roller brush. Am I reassembling the belt and roller brush the right way?


If its a hoover or bissell, one side of the brushroll is slotted and slides. if its a eureka the hexagon end caps must be properly aligned, they go in at an angle. if its none of these provide me with the make and model # and i will give you a detail ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1475 seconds