Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

Dyson dc-07 has been thoroughly cleaned but shuts down if shroud is in place runs fine if shroud is removed

\015 I've been having the problem for about a year. I've removed the shroud and taken it completely apart and it's as clean as new. If I put it back on the vacuum, it runs for about 15 minutes and shuts down. If I keep the shroud off, the vacuum will run forever.\015

Answers :

What is the shroud ?


Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dyson dc-07 has been thoroughly cleaned but shuts down if shroud is in place runs fine if shroud is removed


What is the shroud ? ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a roomba 551. Have cleaned and removed every bit of dirt and hair off it bu the brush cage won't close when the larger bush is put in. The cage will only click locked on one side, and the other side keeps hitting the brush and won't close. It's almost as if the bursh itself is not even, but this doesn't seem to be the case either. I've even tried removing the yellow rings, but makes no difference. Occasionally it runs fine, but most of the time the roomba just hobbles and clacks as i


Hi, had the same problem, it was like the main brush no longer fit into it's slot, so the brush cage would not latch. I discovered that the yellow bearing tip on the main brush twists off, and inside I found a lot of hair twisted around the pin. Th ... Vacuums

Bosch canister vac BSG81313. Took cover off to remove lots of hair, dirt etc from running without bag in place. Everything went back together OK, but cord reel spring went zip when cover was removed. How do I rewind the spring so there is tension when the cord is pulled out ? Wound cord back onto reel, but reel just clicks ever revolution etc...no tension when cord is pulled out of vac. Bob


The spring inside the hub of the cord wheel has escaped from the locking tab. You must completely dismantle the vacuum to access the cord wheel - take it out, reattach the spring and reassemble the unit. All you need is a phillips screwdriver, a pai ... Vacuums

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Mine does the same thing. There is no suction. I found that there is a door that opens when you tilt the handle in the down possition. I think there should be a spring in place so it can open. Until I find a replacement spring I have to open the door ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Either the hose has a clog, or the inlet down by the belt is clogged. Is there suction at the end of the hose, if not then it is clogged. If there is suction, then it has to be clogged down below by the brush roll, check that inlet. There also is ... Vacuums

When trying to use my Hayden Model 3600 central vac when trying to turn on the unit runs for 1 or 2 seconds and shuts off and continues to do so while switched on. I have thoroughly cleaned the filter and dirk canister but the intermittent running still occurs. Any suggestions?


... Hayden Industries SuperVac 3600 Central System Vacuum

Dc35 pulsing Hi I have a DC35 it works fine until i put the main head on and then the motor starts pulsing and cuts out after about 10 secs. If i remove the main brush head it runs fine again ? Please HELP :)


Check for debris in the head and remove ... Dyson DC35 Handheld Vacuum

I have a Eureka 5902AVZ and the brushroll does not work. when i remove the belt, which is not torn nor worn out, the motor spins perfectly fine. Though when i put the brushroll back into place, it shows that the motor is trying to spin, but with resistance. it seems the brushroll will not spin if locked into place, because there is no attachment on the left side of the brushroll that will allow it to spin freely with the belt. am I missing some parts or is there something else wrong?


Hi and welcome to Fixya. I am Kelly. \015\012\015\012You have correctly identified the problem as the brush roll itself. \015\012\015\012There is a bearing under each end cap of the brush roll. You can gain access to the ... Eureka 5902AVZ Bagless Upright Vacuum

Epio 6500 canister electrolux won't stay running...says the bag is full even when it isn't. Will start but as soon a load is placed on the unit it shuts down. Any thoughts?


There might be something stuck ... Electrolux Epic 6500 Vacuum

I HAVE A BISSELL PROHEAT 2X HEALTY HOME, IT WORKED JUST FINE THE LAST TIME I PUT IT UP. YESTERDAY, I NOTICED THE FLOW GAUGE WAS NOT SPINNING, SO I CHECKED AND SURE ENOUGH NO WATER WAS COME OUT. I CHECKED AND ALL THE TUBS AND EVERYTHING ARE IN THE RIGHT PLACE AND HAVE LIQUID IN THEM. HAVE TRIED PRIMING CLEANING THE BRUSHES RUNNING HOT WATER THROUGH IT... HELP


Have you made sure that the tanks are seated properly and the red \012(or black) auto-load gaskets are in place. \012Check the bottom of the Water Tank and the Formula Bottle to make \012sure each has a red auto-load gasket attache ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Euro-Pro EP750M runs fine for about 15 seconds, then shuts off


... Euro-Pro EP750M Stick/Hand Bagless Handheld Vacuum

My Dyson vacuum works fine for cleaning the rug but the hose doesnt get any suction at all. I removed the hose and all the parts around it that I could and dont see any clogs or broken pieces. I lost my manual so I dont know if this is addressed, or if there is a switch Im not flipping. Gave it a thorough look but found nothing.


Hi there,Sorry to hear you're having a problem with your DC07. If you have suction through the cleaner head but not through the wand, it sounds as though you have a blockage. Although you say you've already checked for these, you may find ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Lux 5000 Vacuum will start and then shut off with hose installed. W/O hose it runs fine


Some times that happens when the full bag indactor is broken call and ask electrolux or the guy that left his number what he thinks :) ... Electrolux Lux 5500 Canister Vacuum

Vacum runs fine with hose disconnected and soon as any pressure is put to hose recepticle including your hand it shuts off


These machines have a "Suction" sensor this has become blocked or gone faulty, or the microprocessor has... yes there is one in here too. Probably going to have to get it looked at? ... Electrolux Epic 6500 Vacuum

Motor pulsates When I pull the starter and keep it above the floor it runs fine. When I put it on the floor the motor pulsates a few times then shuts off.


Hi there, it's Jack at Dyson.If your DC44 Animal makes a pulsating noise then shuts off, it's very likely there is a blockage in the floor tool, wand or bin inlet. It's easy to check for this - just follow the steps in our Support guide: ... Dyson Animal Bagless Cordless Hand Vacuum, DC44

I have a Kenmore Progressive Upright Vacuum - Purple, and it worked just fine. I emptied the canister (like always) and put it back in place. I turned on the vacuum to it immediately shutting down (motor) and only the lights come on. There is no movement/noise/suction at all! Any suggestions? I have tried everything. I have no idea why it did this.


Make sure that something didn't fall into the fan assembly in the base when the canister was removed. The motor should have an overload reset switch. Try moving the motor manually (power plug out) to make sure that it isn't bound up. ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Let's try this again. The main vacuum and hose works fine, the "foot" does not. When I turn it on, it shuts off automatically and the light comes on telling me to "check brushroll". I did this and removed all hair, strings, etc., Still won't work. Please respond. The last post took over 30 minutes with no response.


Sounds like you have hair or carpet buildup in the roller and it is not freely rotating and you are getting an error. If there is no buildup, then roller bearings may be frozen up, or the unit has a faulty capacitor and is not going to work due to el ... Vacuums

No power Our dyson DC07 was working fine, then we pushed the button to turn it on. It started to run then shut off and now it is like the power is no longer there. I have checked outlets and they all work. Is there a fuse of some kind in this unit?? If so, how would I get to it?


The motor will have a thermal cut out,however chech your plug fuse and the cable as it enters into the off on switch. its known to snap here within insulation..... ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Brushes only work when Dust Bin is removed!! I have cleaned & cleaned this thing! It runs for about 2 mins & stops, says "Clean Brushes"! and now it's very noticeable it's not picking up well... but is picking up a bit. I take the dust bin out, and the brushes spin.... and it has much more power.... and is very clear it is working! But it's useless without the dust bin! LOL It's only 9 months old.... called customer service, but it was the one time it worked just fine! Of course, I thought I'


HI, If the brushes work , without the bin, the problem , the problem could be caused , due the failure at the bin lock mechanism. There is a sensor that checks if the BIN is connected properly or not. This problem is best resolved by getting ... iRobot Roomba 560 Robotic Vacuum

My powerhead on my EXL Tri-Star goes on then shuts off. When youturn it upside downit runs, then back on the floor it stops. Is it the belt inside the powerhead and if so to I take the head apart and replace this belt. Can any vacuum repair place fix this if I have the part. Vacuum was purchased in March 2000 Thank you, Dianne Miller [email protected]


A vac shop is probably going to require you to use their parts for warranty purposes. but its pretty simple. most shops should be capable to do it. ... Vacuums

My Miele White Star Model # S3141 was running fine, then stopped mid-vacuuming. I changed the bag and cleaned the filters (which were dirty), let it cool off, and tried to start it up again, but no luck. What do I do now? Are there any repair places in Ft. Myers, FL?? Thank you for your help.


... Miele Vacuums

Was running fine and then just shut off - Rainbow E series Canister Wet/Dry Vacuum


You may have too much water in it. And if you add deodorizer to the water, it sometimes can cause too much foam causing the vacuum to shut off.Jim ... Rainbow E series Canister Wet/Dry Vacuum

I cant get my kirby to blow out...bag is removed from seating...its plugged in...i attach the hose to the place where the bag goes, but it wont run


I did get it to work! It was a struggle, but It finally hit that hidden switch just right. The hose attaches to where the bag goes, and it just wouldnt seat properly. I suppose there might be some wear there on the hose end that twists in . ... Kirby Vacuums

Vacuum shuts off, bag light on, runs fine without hose connected


I'm not sure if I understand your problem completely, but if it is your full bag indicator that is coming on, even with a new bag, it's probably your control valve. These can be replaced by your dealer. When working correctly, the control valve shoul ... Electrolux Epic 6500 Vacuum

I have a Hoover Mach 2.7 Windtunnel that shut off during use and wouldn't turn back on. Was doing kitchen floor and running fine. Though a breaker tripped but didn't...what could it be?


Hello, \015\012\015\012It sounds like your thermal reset switch inside of your Hoover may have gone bad. When a vacuum cleaner doesn't turn on it, it's either caused by one of four things. \015\012\015\012Ele ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0521 seconds