Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

Outer actuator doesn't stay in place

\015 So I do not get full suction...when turn over powerhead, remove soleplate, look at area where internal hose connects, then disconnect internal hose..can see a round hole which I assume opens and closes suction for internal hose...it is sometimes stuck closed, or only half open..when I either move the outer clutch actuator back and forth (from floor to carpet) or push the reset on top of powerhead in the outer actuator area when vac is reclined it will resume full suction, but it does not stay in the full suction mode...in other words it appears to not stay in proper placement\015

Answers :

Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Outer actuator doesn't stay in place

... Dyson DC07 Bagless Upright Cyclonic Vacuum

Not picking up as well as should be...dyson dc07.... From bottom of powerhead in area of outer clutch actuator the round opening for suction is only open halfway, when I move the outer clutch actuator

... Vacuums

The retractable handle doesn't stay in place. a small spring came out near the button that you push to slide the handle up and down to change the length. i need to know where the little spring goes. there is a small pin that the spring fits around but i can't seem to get it to go back in place once the spring is on the pin.

... Panasonic Kenmore Canister Vacuum Vacuum

When i hit the power button on my miele carina, it doesnt lock and stay on. i have to hold down the power button for the power to stay on. Please advise

Try a little WD-40 sprayed sparingly on the button. work the button a few times- may be sticky spring or contact. if that doesn't work, check with retailer where you purchased it- see if you can get a replacement switch! if you're handy, or have a ha ... Miele Carina Vacuum Vacuum

Regarding my Kirby Generation 3 upright vacuum cleaner: the handle does not lock into place, but rather falls to the floor. Any thoughts on how to get it to stay in place? Also, I lost my owner/operator manual. Can I download one to learn how to clean and maintain the vacuum?

The plate that catches the handle to lock has a hidden spring behind that plate.I would leave it alone for the unit is pressed together. Used ones are found most everyday on Ebay. The owners manual maybe found on this website\015\012\015\ ... Kirby Generation 3 Bagged Upright Vacuum

Generation 4 Apparently, my belt came off while vacumming. I had a lot of hari entwind on the roller, so cleaned off the hair.... but now I can't seem to get the belt to stay "in place". Is it supposed to move around on the brush? or be held in place? It seems to me when I try to get the hook to grab ahold of the belt, it is going tohe wrong way to grab it. Please HELP!

First off get a new belt, I am sure this one has stretched. Then put the belt around the brush roll, put it in the center, put the bottom plate back on. Then turn the big knob on the front and turn it until it locks, you will know if it grabbed the ... Vacuums

I have a proheat carpet cleaner model 3 7901. the problem is the brush on the bottom of the machine plus the two end parts and the belt came out. i put everything back but they popped out, they are not staying in place. what am i doing wrong or what do i have to take out to get everything in place correctly?

Hi\015\012\015\0121. You’ll need to follow this procedure to assemble your unit back together.\015\0122. Make sure the foot pedal is in the proper position.\015\0123. The SmartMix should be properly loaded into the main ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Hoover Mod U8146-900-When you press handle release lever vacuum falls down it doesnt stay up

... Hoover Vacuums

New belt didn't stay in place

Make sure belt lifter is on proper setting/ turning until stops/check right size belt ... Kirby G6 Bagged Upright Vacuum

I have a eureka power paw that keeps breaking belts. there doesnt seem to be a part that keeps the belt in place

My belt keeps breaking too, but worse is that I can't find out the size for replacing. Who knows the size I need for the Eureka Power Paw? ... Eureka Vacuums

The brush attachment will not stay in place on my Hoover steam vac F5858-910

Check the bottom of your brushes. It should have a long shaft sticking out of of the middle of it which locks on the base. If you don't see the shaft, the brushes are broken ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Epio 6500 canister electrolux won't stay running...says the bag is full even when it isn't. Will start but as soon a load is placed on the unit it shuts down. Any thoughts?

There might be something stuck ... Electrolux Epic 6500 Vacuum

Bag will not stay secured on docking clip. Outer back falls completely off of vacuum cleaner.

... Oreck XL Deluxe U3700 Bagged Upright Vacuum

I have a bissell momentum ive broken 2 belts the brush doesnt seem to be spinning they are placed into the side slots correctly what could be the problem?

Most likely your brush needs to be removed and cleaned.\015\012Clean all debris that might be in the bristles of the brush. You will see a holder for the brush on each end that holds it into the frame of the vacuum. The two holders should turn free ... Bissell Vacuum - Momentum Cyclonic 1 ea Bagless Upright Vacuum

Im trying to replace the belt in my widepath tempo. Once I put it in the roller.... I don't see what it should attach to, to work and stay in place. ?? Please guide me.

... Hoover Vacuums

Broken piece The black plastic octagonal end of the brushroll has broken off the brushroll, so the brushroll won't stay in place. Can I get another little piece to attach onto the brushroll? Or do I have to get an entire new brushroll? And if so, do they sell replacement brushrolls? CP

You will have to replace the brush roll, part #60844-5, belt # 61120B. You should be able to get them from a repair shop, get the right one or it won't work right. You maybe able to go eureka.com and order direct. ... Eureka 4700A Maxima Bagless Upright Vacuum

Cleaned filters. Now the ball filter does not stay in place.

... Dyson DC25 All Floors Bagless Upright Vacuum


... Hoover F7205900 SteamVac V2 Wet/Dry Vacuum

Dyson dc7 front will not fellow floor. every thing works , when tip handle back front justwont stay in place to vac

Pls explain ur problem in more detail ... Vacuums

Changing belt while changing the brush belt the cog/gear fell out, ive tried to push it back it but it doesnt seem to stay...is there a way to snap it back in or is the unit broke?

You will have to replace it, and it comes on the pump not separate. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Vacuum will not stay on, new bag in place and power to machine.

It sounds like you have a bad control valve. Take it to you nearest Aerus (formerly Electrolux) dealer and have them change it for you. It shouldn't be too expensive. Good Luck!! ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Shampooer the small ring screen that makes the subs basically wont stay in place. no matter what i try it keeps popping off

Hi,\015\012I suggest regular scotch tape or masking tape. Just take the screen out and cut a piece of tape into strips that are just wide enough to fit the outside of the screen ring without any excess. Put the tape strip(s) around the outside ... Kirby Ultimate G Bagged Upright Vacuum

I have a Dirt Devil M088400 - Vision Turbo Vacuum. A spring fell from the bottom and the carpet height adjust isn't working. The rollers under the unit won't stay in place either. Can you tell me how to put the carpet height adjust back together?

The roller attaches to wheels. There is a spring that attaches from roller to hight adjustment selector which is a plastic peice with a little hook on bottom that spring attaches to. Both peices should have a hook that the spring ttaches to. ... Dirt Devil Vacuums

Telescopic handle I don't think I have the exact same vacuum, although mine is a fantom upright bagless. I can't get the telescopic handle to stay in place. It pulls out whenever I try to pull back the vacuum. Any tips would be helpful! Thank you

Sometimes the locking mechanism for the wand wears out, make sure u have it all the way in and look where it locks and see if it looks worn ... Fantom Vacums FM760 Twister 500DX Bagless Upright Cyclonic Vacuum

On/off switch we have two of these vacuums at work, and both of there on/off switches dont work too well. its hard to explain, but when u normally turn it on or off theres a little resistance in the switch and you hear a click, with both of ours the switch moves freely back and forth from on to off, no resisntace, no click, and the machine doesnt stay on, or off for that matter. the switch just moves back and forth.

... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0240 seconds