Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

Vibrating When I turn on the vacuum , the bottom where the brush is vibrates to make a loud sound. I cleaned the brush and took the gray plate off. when replaced made louder.

Answers :

I misunderstood the original suggestion to fix this issue. It was a misalignment on the beater bar. I fixed that and voila! Vacuum is perfect again. Thank you
Check to see if the beater bar (the one with the brushes_ is seated properly. The pieces at the ends of the bar are keyed to only fit in one way, but if you're not careful, you can force it in...or force one of them in and it get off-balance.

And Call Dyson...their support is great!
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Vibrating When I turn on the vacuum , the bottom where the brush is vibrates to make a loud sound. I cleaned the brush and took the gray plate off. when replaced made louder.

I misunderstood the original suggestion to fix this issue. It was a misalignment on the beater bar. I fixed that and voila! Vacuum is perfect again. Thank you ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have the Sharper Image EV-HD15 Cool Mist Humidier Ultrasonic 1.6 gal humidifier. I purchased it last year. Yesterday I took it apart to clean as per instructions. I feel that I may not have place the round housing (which is secured with 4 screws) back correctly. When I turned the machine on it made a whirring sound. I took the unit apart again and rotated that round piece moving the opening away from the opening on the tower. The whirring sound was reduced but there was still a sou

... Sharper Image Vacuums

I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom

Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Recently my central vac system started making a louder than usual and laboured sound when in uise, enough so that I took note and inspected the canister and motor while running. The motor was trowing off blue sparks and looked like it could 'POP' at any moment. I will not risk using it until I know what the problem is and how to repair it. My assumption is the motor needs to be replaced. The system came with the resale house I bought 3 yrs ago but I do not know the age of the system itself.

... Vacuums

Hello. I took the sole plate of to clean the brushes on my dyson dc14 however the brush part came out and i put it back in but since then whenever i switch it over to carpet setting it makes this really horrible clicking grinding sound its only new have only used it a couple of times.

You really need to take the sole plate back off and make sure the belt is running exactly where it's supposed to go and not looped over a piece of plastic or anything. More important is that you make sure the ends of the brush are seated properly an ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My Miele Twist vacuum will not lock into the upright position. Also I sucked up a tassel from a throw pillow and have a clog. I took off the little clean out plate on back...it isn't in that par

... Miele Vacuums

Wont re-assemble I took the bottom plate off to clean out the rotary bush and can not get the plate back on! I think it is the position of the roller but no matter which way I place it when i turn it , it flicks back into the place that means i cant put the plate back on!

Assuming you did not remove the brush roller to clean it and consequently did not reseat it, I am guessing that the bottom plate is not reinstalling as it should. On some uprights, the bottom plate hooks in at the front and is latched in place with c ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Vacuum has new bag but won't pick up dirt. Cleaned flat filter and it made it worse. Do I need to replace rectangular filter or can I clean it. If so , how? If not, do I need to take it in for repair, ir should I get new parts? Thanks!

It's clogged somewhere. Disconnect the hoses where you can and check for obstructions. Run a coat hanger down the hose if you need to to clear the obstruction. ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Unbeknownst to me, someone took the bag out of my Kenmore Progressive vacuum and failed to replace it. I have been vacuuming without a bag for months, and today the vacuum stopped sucking. When I opened up the front to replace the bag, tons of dirt and dust came pouring out. I thoroughly cleaned the vacuum, put in a new bag, but still no sucking power. Just dust coming from the rear vents where one of the filters is. Is the vacuum ruined, or is it a simple solution of buying a new filter?

Sounds like you need to buy a new motor. All that grit and dust will ruin a motor and I'm surprised it lasted as long as it did.\015\012This is where a vacuum that won't run without a bag would have been nice. (Aerus for one) ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

My Dyson DC07 is screaming load. I have replaced the lifetime filter and the hepa filters. I also replaced the clutch and brush. I took the canister apart and cleaned it. It works, but is so loud something else must be wrong

... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a Dyson DC14 It started making a high pitched squeel so I took the filters out and cleaned them and i checked all places that pull out on the vacume to see if there was anything clogged. I also cleaned the roller brush. but when I turned it on, after a couple of seconds the sound came back again. can you help

Sounds like motor bearings are gone .... sorry. ... Dyson Vacuums

Vacuum sucks up dirt and expells it back onto the carpet as I am using it. I have replaced the bag and took the bottom off to clean - even cleaned up the area where the dirt should go to make sure it was not clogged.

Good chance the tube from the base up the handle is clogged. Try removing the bag and look at the exit, that is where most clogs on this unit occur. Look for hair, string, etc. If clog is not there, then may be in the tube or at the base swivel unit ... Oreck XL2600 Vacuum

My dyson dc40 multifloor seems to have gotten louder than it was 6 months ago when i first bought it. Sometimes it sounds like a whistling noise. I religiously clean the filters, empty the canister, check for clogs, and clean hair from the brushes. Is this normal?

... Vacuums

Wiring diagram for Model #11635922500 - KENMORE Upright vac I took the cover off of the vacuum to repair the power cord and must have pulled a wire out of its wire nut by the sweeper bar. If I had a diagram it would be no problem to replace. The bad has four short gray wires coming out of it. It is one of the gray wires that has come loose.

... Kenmore Vacuums

Noisy vacuum I have a eureka capture that I bought in april it's making a horrible high pitched squeal type noise, I have made sure my roller is clean, my filters are clean, i replaced my hepa filter and there are not any blockages I don't know what else the problem might be. Could you please offer other suggestions to fix this?

... Vacuums

Does the hoover runabout u427-930 have a filter? I replaced the belt and next to the light bulb was a square gray mat that looked like a filter covering a screen full of holes that looked like the motor was behind. I think it was a mat of cat hair so I took it off and threw it away; I just want to make sure that it wasn't a filter that I need to replace.

From doing a search on the internet and hoovers website it looks as if this unit does not have a filter. Such as a hepa that needs to be replaced or that is washable. So i think you are safe and dont need to worry about it. ... Hoover Elite U5061-900 Bagged Upright Vacuum

It sounds as though a belt is rubbing or slightly off-track. The sound is extremely loud. We've removed the plate around the brush bar, made sure the brushes are free of dog hair, and found that the belt appears to be on track. What should we try now? We haven't tried to use it to check for suction for fear of doing real damage! Thank you. Marcia VanDyne

Is the sound coming from the head unit where the belt is attached? When you power up the vac, can you watch the belt to see if it is frayed or running off track. I have the same Dyson and had this same issue, cleaning the head cured it, but your issu ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Kenmore quick clean model 116.36724500 and the belt popped off so we took the bottom off and put the belt back on, but now cannot get the bottom floor plate back on! Please help! :( I have no

... Vacuums

No suction I cleaned and checked all hoses, sounds like something is stuck inside, like a sock, took machine apart as much as I could and couldn't find anything. Any suggestions?

Ok first thing to do is remove & clean the 2 piece premotor filter or purchase new.Now remove soleplate from bottom of machine to do this rotate the 3 plastic screws to unlock position. Lift sole plate off now remove any blockagers or ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

The head on my canister vac vibrates, smells and makes a bad sound. When I took it apart the inside of the "end brush tufted" piece had bits of the plastic broken off. Should I replace the Agitator Unit Assy or could this be the motor?

If you are talking about the end cap is broken off the agitator, I would replace the agitator. you can check the motor by turning on the vac without the roller installed. ... Vacuums

I have Optima, 12amp Eureka vacuum, Model 431, AXZ type and the extension hose for cleaning corners and edges --the plastic part that the attachments fit into has a piece broken off and tools don;t fit anymore. It looks like the hose attachment can be replaced--can it be and if so--where can I get a new hose attachment. It seems it is cheaply made of plastic and really shouldn't have broken a piece off.

... Eureka 431A Optima Bagless Upright Vacuum

Wondering if the head is plugged up because it makes a sound like air is escaping somewhere. I've replaced the original cloth bag with a comparable "O" paper bag from Sears. I tried to see if there was a clog in the hose by placing a broom handle in the hose to see if something would loosen. I also cleaned the filter and the air filter. If the head is plugged, how can I fix it? We can't get the vacuum apart. Thanks.

I had this problem, but suction improved when the attachments were properly secured in their holders. ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Is there any way to repair or replace the belt GUIDE on the inside of the belt compartment of a '97 Hoover Wind Tunnel (not self-propelled)? It became twisted when a belt broke and now the belt rubs against it and sounds really weird, and I'm sure new belts will continue to break.. This guide is a long piece of molded material (part of the compartent wall) to keep the belt from coming off the pulley. It also had a sort of metal clip on it. It was loose and I took it off because of the way the pa

Honestly you should take it to a vac.shop they can fix any vac. ... Windsor SR12 Sensor Bagged Upright Vacuum

How to replace wheel bracket on dirt devil. I have a dirt devil swivel glide and I took off the wheel bracket to clean out a clog and now I cant seem to get the wheel bracket back on.

... Dirt Devil SwivelGlide Bagged Upright Vacuum

My Dyson Aminal Vacuum simply will not turn on. I plugged it in this morning, pressed the power button- and nothing. No warning sounds, simply silence. Sigh. Nothing is wrong with the wall outlet.The vaccum is 3 years old but has run perfectly until this point. The brushes are clean of any accumulated hair. What part might need replacing?

The power switch may need to be replaced. Call the Dyson helpline - they will give you the location of an authorized Dyson dealer in your area who will be able to replace the switch. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1060 seconds