Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

Dyson DC07 main power switch

\015 Power switch fails to stay in ON position when pushed. I can get a\302\240\015\012replacement switch but can't figure how to remove the old switch\015

Answers :

You will need to replace this switch remove the bucket from the front of the machine and the handle and pipe from the back on the front of the switch housing you will see a screw remove this screw on the back you will find two little catches one on either side push these with a screwdriver then the sides of the switch housing will pop out from the chassis now on the front theres another on the bottom of the housing push this down and pull the housing off from the front when replacing this part be carefull not to trap any wiring
I just had the same problem and took apart the canister part, cleaned it real good (a ton of dust came out of it, i shook it out and vacuumed it with another vacuum and put it back together and it works fine.  I think it may be a like a kill switch so that the motor doesn't burn out on you.  If you use tape or something to keep the button down I think the motor will overheat and burn out eventually.  With all vacuums, I've learned they have to be cleaned pretty reguarly.  I vacuum every day and there is no end to the amount of dust it picks up, no matter how much I clean.
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dyson DC07 main power switch


You will need to replace this switch remove the bucket from the front of the machine and the handle and pipe from the back on the front of the switch housing you will see a screw remove this screw on the back you will find two little catches one on e ... Dyson DC07 Bagless Upright Cyclonic Vacuum

HOW DO I CHANGE THE MAINS POWER CABLE ON A DYSON DC07? my wife cought the cable under the dyson and has stripped it to bare wires so i need to change the cable. i have taken a cover off near where the cable goes into the machine but now cannot get any further


How to open the cover near the cable for dyson upright vacuum ... Dyson DC07 Bagless Upright Cyclonic Vacuum

DYSON POWER SWITCH TURNS OFF - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My dyson dc07 animal won't power up. I have checked the fuse and the switch


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

How do you get into the switch area of the Dyson DC07 to replace the mains cable?


... Vacuums

I tried to use my Dyson DC07 in upright mode but the power kept turning on and off. I turned it on then off and a spark came out of the switch. Now nothing?


Hi there,Sorry to hear you've had a problem with your DC07. Please get in touch with us, free, on 08002980298 (UK), or 1866MYDYSON (US), so we can help.Kind regards,JackDyson Customer Service ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Power switch won't stay on - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


The only fix for this problem is to replace the power switch. Any vacuum repair store can do this for you or order you thepart. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

HOW DO I CHANGE THE MAINS POWER CABLE ON A DYSON DC07?


Have a look at www.dysonmedic.com which has some excellent info on your machine. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

No power when switched on - Dyson DC07 Bagless Upright Cyclonic Vacuum


It may be the on/off switch gone bad this video will show you how to replace. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson dc07 suddenly lost all power. Bad power


This could be the switch, but could also be the motor.\015\012The motor has a built in over-current protection device which normally automatically resets itself, but if the motor has had it, it then just cuts out again as soon as you switch it ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Vax powa 4000 wet and dry - no suction Both power and pump switches light up. Pump makes clicking noise. Vac motor only powers up briefley when in switched on cindition and mains plug is being inserted into socket.


... Vacuums

I have a Dyson slim DC18 all floors, the power switch is bad it won't stay latched I would like to get 2 of the switches. Dyson 18 s/n 334-US- A 26163 Nelson LePla 5495 S.Fordney RD Hemlock MI 48626


You can order the switch from the following sites. According to the first site, the DC17 and DC18 switches have the same part number, so I'd use the second site. It costs less. I didn't check the shipping costs, though.\015\012 ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

Plugged my Dyson in this morning, switched it on and power came on for not even a second and died. No power what so ever to dyson - checked my house sockets, changed fuse. Still not working - dead as a door mouse. What could it be? Many thanks Sam


It is either your power cable, cable rewind mechanism or your motor. \012\012Try switching it on, and wiggling the lead near the plug and see if it fires up. If it does, remove the moulded plug and fit a standard plug. \012\012If not, lik ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Dyson DC07 hi My dyson dc07 wont power up, any thoughts on what could be causing the fault. ie does it need new motor.


First, check your outlet for power...plug something else in. Then, inspect the cord and check the power switch. You can use a multimeter to test across the power plug of the vacuum in the ohms position. Turn the switch off and on. If it does not ... Dyson DC07 Bagless Upright Cyclonic Vacuum

How to fix a new power cable to a Dyson DC07 - Dyson DC07 Bagless Upright Cyclonic Vacuum


Try this site: http://www.sparesaver.com/help-and-support/dyson-sec ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Replace power cord on Dyson DC07 - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


The following link will take you to an article on how to change the motor on a DC07. Look at photos 4, 5 and 6 which shows how to disconnect the power cord.\015\012\015\012 ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Got a Filter Queen Majestic Limited Edition, the one with the high and low power switch, an I have to change the power cord. How can I open the main unit to reach that power cord? Thanks,


First remove the top cap under your handle. \012Then, remove the three screws under the handle. \012remove the rubber cover on the switch\012undo the clamps on the side of the unit\012lift off the chrome cover with the cord on ... Filter Queen Majestic Canister Vacuum

Replacing the on/off switch on Dyson DC07. After the switch retaining screw is removed, how is the switch removed? Does it just pull out or are there retaining tabs ?


Have a look at www.dysonmedic.com which has some great info on your machine ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My Dyson DC07 vacuum started to run slower after being on for a little while and then would run normally again. I have switched on today and it has just stopped. When I push the start button, on occasions it almost starts and then doesn't. I am wondering if there is a problem with the switch and if so how can it be fixed? Thankyou.


The motor running slower was the motor starting to burn out. The "almost start" is the brushes making intermittent contact with the armature in the motor. \015\012\015\012Your machine needs a new motor Pam. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I'm trying to remove the power switch assembly for my Dyson DC25 so I can replace the power cable. I took out the 3 screws with a T15 screwdriver and released the top two retainter pins, but the lower half of the assmbly won't detach. Please help!


Replace the two bottom screws but don't tighten up just a few turns in will do, then using the screwdriver push firmly each screw and this will release the lower part of the cover hope this helps. ... Vacuums

Dyson dc03 faulty cable The cable from the mains plug to the on/off switch has split and needs to be replaced. How do I gain acess to the switch ? I am a competent engineer but I do not wish to damage the switch/cover to repair/replace acble.


I've never worked on a DC3, but whilst the shape and position of the switches changes from model to model, most are secured the same way.\015\012\015\012If you look closely at the switch cover (the bit you press for on/off), there is usua ... Vacuums

Dyson will not stay powered on unless power button is continuously pressed. Is this a switch malfunction or something else?


Yes, you probably need to replace the switch - call the Dyson helpline, they'll give you the info for your closest authorized repair dealer who will open it up and replace the switch for you. ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Dysin dc07 the power button is broken - Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum


Switches are available if you search on eBay for a few pounds, and if you've ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

No power to Dyson. Plug & fuse checked - Dyson DC07 Bagless Upright Cyclonic Vacuum


This could be a faulty cable or switch, but could also be a faulty motor.The motor also has a built in over-current protection device which normally automatically resets itself, but if the motor has a serious fault or the over-current device it ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson Animal is not powering up - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


It might be the eletrical inside the machine.or even the power cord. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0552 seconds