Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

Poor Suction Heya! So I just picked up a used Dyson, but when I vacuum with it, the suction is pretty weak and it spits all kinds of stuff out the back and into my feet. When I pull the hose I have good suction, but in regular mode it hardly picks up anything. The brushes are spinning, and it eventually will clean an area if I go over it again and again. Maybe a clog somewhere? Please tell me that Dysons have better suction than my $50 Dirt Devil! Thanks!


Answers :

I recently bought a second hand Dyson DC07. Its suction was poor. I removed all the un-clipable pipe bits and to remove any blockage but it all looked clear. The Final Sponge and hepper filter did have a lot of dust in it and the rotating brush was full of hair but nothing bad.
\015\012
\015\012I eventual gave in to curiosity and removed the three screws in the top or the yellow removable dust collection tube and cyclone bit to see what was in there. The mechanism to release the flap at the bottom of the collection tube does not allow you to remove the lid completely but it does open far enough to get inside. I found the whole top section of the yellow plastic bit blocked by a big plug of compacted dust and a champagne cork. If you are willing to take the risk and have a torx 15 screwdriver handy it that part may be blocked. It did get a bit messy.
\015\012
\015\012If I was going to attempt the same procedure I'd remove the dust collection unit from the vacuum cleaner as I did before, but leave the clear tube attached and the emptying flap firmly closed to reduce the mess from the dust falling out the bottom while cleaning the top part.
I had a rethink about leaving the clear plastic cylinder on when trying this repair. If the emptying flap is latched in position before removing the top you won’t be able to open the flap until the unit is assembled again. You may need to get in the bottom of the unit to get the release pushrod to locate in its guide at the bottom of the assembly. I recommend removing the clear plastic cylinder and flap and dealing with the dusty mess made during the repair when your finished.
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Poor Suction Heya! So I just picked up a used Dyson, but when I vacuum with it, the suction is pretty weak and it spits all kinds of stuff out the back and into my feet. When I pull the hose I have good suction, but in regular mode it hardly picks up anything. The brushes are spinning, and it eventually will clean an area if I go over it again and again. Maybe a clog somewhere? Please tell me that Dysons have better suction than my $50 Dirt Devil! Thanks!


I recently bought a second hand Dyson DC07. Its suction was poor. I removed all the un-clipable pipe bits and to remove any blockage but it all looked clear. The Final Sponge and hepper filter did have a lot of dust in it and the rotating brush was f ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Bad smell after using my windtunnel for a couple of minutes i noticed an odd smell. i turned it over and checked, the belts are fine but i cleaned out the hair anyway. after doing that the self propel seems to struggle and it is hard to push. when i look through the window on the top i can see the brush spinning freely but then when i push it, it slows down dramatically and then picks up again. the suction is fine. what do you recommend?


It may be the roller bearings? ... Hoover U5450-900 Windtunnel Supreme Bagged Upright Vacuum

Miele, Flamenco II. 2 probs. 1. the head brush is not turning when I put it on the floor. If I pick it up to look inside...the brush is spinning fast..I put it down on the floor...the head does not spin at all. 2. The suction power has dropped significantly. The suction used to be so intense, the head would **** itself to my floor and hold on...now, hardly any suction at all.


Sounds like the belt is not on correctly on the beater brush or the belt is worned out now for the suction check filters or bags that need to be empty or clean ... Miele Vacuums

My floor brush stopped spinning, I cleaned everything out as per your directions in other posts and following the instructions in the manual. Now the floor brush wobbles and has a hard time spinning when upright. Looking at the end of the brush, opposite the drive belt, the bearing-type end that the brush spins on appears to be off-centered. Is there an easy way to fix this???


... Bissell 3130 Bagless Upright Vacuum

Dc07 problem I have a dc07 cyclonic vaccum and like this model,however, for some reason,it has been very dificult to push and pull for the past month or so. i have completely cleaned the brush assembly,cleared any obstructions in the hoses,and, cleaned the filter.I also checked the belt tension,wich i thought was fine but to no avail.Be advised that the brush assembly is spinning and suction is excellent. It just feels like the brush drags along the carpeting. this is a great vacuum cleaner and


The dyson uses two belts, one from the motor to a clutch and then from the clutch to the brush roller, the belts that they use are not much better then any other belt ( those you should change yearly ) but you cant just change the belts you have to c ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

No suction I have new belts. Everything is clean. No clogs. When I turn it on it smells like rubber , the brush doesnt spin. Everything seems to be free flowing.. Roller brush isnt stuck on the ends. Took off hose to make sure no clogs anywhere. There is not even suction thru the hose with the handle in upright position.


Generally, the problem is that the belt is not running the brushes.  This is caused by one of the following:\015\012\015\012\015\012beater brush is jammed.  This is either an object stuck in the brush or im ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Not enough suction going into my turbo brush so it spins. Ive cleaned it checked the belt it still doesnt spin. how to fix this problem?


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Hoover Elite Deluxe rewind... Air flow indicator stays activated, after filter has been cleaned. Brushes spin, but very little suction. Dirt is not spinning in cup


... Hoover Vacuums

When switching the vacuum (DC17 Animal) over to the hard surface setting (so the beater brush is not spinning), the vacuum shuts off. I cleaned the dust bin and checked the filter. I also cleared the beater brush of hair or debris that was wrapped around it. It still shuts off. Ideas? Thanks.


The drive belt has probably broken. You can get a replacement belt here:Dyson DC17 Belt ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Poor suction The actual sweeper seems to work ok, but the hose attachment has some suction but not enough to pick up things I think it should and not enough to make the power brush spin. I've checked everywhere I can for clogs, but I can't see anything. And there doesn't seem to be any way to check to hose itself for clogs. I've cleaned out the container and the filters, but there's still a problem.


Check the inlet down by the brush roll, make sure it is open, if it is then the hose itself must have a clog. If the hose comes off, drop something like a marble in one end and see it it comes out the other end, if it doesn't then you have a clog. ... Dirt Devil M1100009 Reaction Soft Touch Cyclonic Upright Vacuum Cleaner Vacuum

Air flow indicator stays activated after filter has been cleaned. Brush spins, but very little suction. Dirt doesn't spin in cup.


Your vacuum is clogged. Check all of the air pathways, hoses, etc. The most common places to check are anywhere there's a joint in the airways, and also directly behind the brushroll. \015\012\015\012-R ... Hoover U5507900 Elite Rewind Bagless Upright Vacuum

I cleaned out my brush in the bottom front, cleaned out the small tubing going into the canister, and the canister itself. I also changed the filter.I snapped everything back into place, but Since then, it doesn't seem to have any suction and there seems to be a space between the canister and the bottom of the vacumm where the canister sits. At that area, you can feel air coming out when trying to vacumm and it just doesn't pick up, it seems to be just blowing stuff around.


You need to really look at it some thing is out of line you shooed not have\015\012any spaces in the top or bottom\015\012pull the canister back out and look at the pins that you lined up with the\015\012to ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom


Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Have Hoover F7452900 spin vac carpet shampooer and brushes won't spin. The screen by the brushes is clean and they are place in position to clean on carpet. I noticed that when I have the brushes out of the machine and turn it on that the white square that is on the base of the machine does not spin--this is where part of the brush connector fastens to make bristles spin.


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hi¬ on my DS04 there is strong suction but not brush roller spin. I've cleaned top and bottm filters too.


... Dyson Vacuums

WHEN I PUT THE MACHINE ON TO CLEAN TH CARPET THE WATER DISPENSES INTO THE CARPET AND THE BRUSHES do not SPIN and theres NO SUCTION TO REMOVE THE WATER FROM CARPET


Make sure the lower tank lid is on securely, clean the intake filter on the top right of the machine. ensure the front panel is installed (the square to remove for hoe use). this has to be in place for carpet operation ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My vax power 8, 2200 watts 300 air watts 4L capacity upright Hoover is brand new, I emptied out the dust/dirt collecter and cleaned the motor filter yesterday for the first time, i switched it on and all fine, the brush is spinning and the hose is sucking, put the Hoover to work it's fine for about 30 seconds then then suction stops and its dead it won't collect no more, so switched off taken apart again and the motor filter is blocked and full of dust, so I unblocked it, do the same process aga


I had the same problem. It looks like the seal on the lid on the bottom of the cylinder has fallen out when it was emptied. There is no longer a proper vacuum being created so you don't get the cyclone effect and the dirt doesn't collect where its su ... Vacuums

No suction at all on my Kirby just cleaned the brush, etc... had a hard time getting the belt back on... really hate this vacuum cleaner


I have a kirby Diamond series and the 'green light' on the upper right side (while standing behind the vaccum) does not come on and when it doesn't come on I noticed that it does not sound as though it is picking up at all. I have changed the belt, ... Kirby Ultimate G Bagged Upright Vacuum

My Steam Vac F59149 will not vacuum up the cleaning solution. I have checked the usual culprits. The dirty water tank is empty, the yellow float is not up too high. This is a relatively new appliance, so the way for the water is not blocked, there is just no suction. The warm air is blowing, the brushes are spinning. What next?


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I purchased a hoover windtunnel 2 model#u8361900 in Dec 2007.I am very disappointed because the self cleaning filter is not turning and particles keep clogging in that area. I have manually removed the particles but the filter will not turn.I also haven't been able to use the pet brush for some time.The cleaner has not been used hard about once a week since it was purchased.I am not happy that this product has stopped working effiently since purchased 6 months ago. Thank you Marcia Long Pottstow


The filter stands up right.the bottom goes in first then snap in the top.turn it by hand and you should hear it click if you have it in right ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

When cleaning carpet, I heard a single pop sound, and the suction of the water from the carpet stopped. The brushes are still spinning. Can you help?


I think there is some thing in ur machine, , may be there is some dust or metal piece, , , jst open it nd clean it, , , then try again ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

Brush will not spin. filters are clean, no clogs, belt is fine. remove canister, it works fine plenty of suction.


Probably a good idea to remove the brush and clean as best you can.\015\012Add some WD40 at each end by the plastic clips and turn by hand until they move freely.\015\012Reassemble being sure the belt is on properly. ... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

The brush is spinning (and has been cleaned), there is a new bag, but we get no suction.


The reason the brush is not spinning is because the belt is stretched or broken. You can get a replacement belt here:Hoover U5491-900 Belt ... Hoover U5491-900 Bagged Upright Vacuum

My Kenmore canister model (116) 26212601 works in hard-surface mode (basic suction), but the brush won't spin for carpets, and when I try to turn it on, it makes a whiny sound and then turns off as it does when I need to press the overload button. I looked inside a bit, and the belt isn't broken--it seems fine. So not sure what the problem is. Thanks for any help.


... Kenmore 27815 Bagged Canister Vacuum

The flexible brush on my unit does not spin. It did 'by accident' pick up a cat poo that didnt make the litter tray while I was out, (and it happily spread it all over the house and skirting boards). I cleaned the unit, removed the base and wiped everything clean. I've unscrewed the flexible brush and cleaned underneath it but it still wont spin. Any suggestions?


... iRobot Roomba 530 Robotic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0865 seconds