Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

LOUD GRINDING NOISE ALL OF A SUDDEN , LOOSE BELT ?

\015 ALL OF A SUDDEN MY dc07 STARTED MAKING A KIND OF GRINDING NOISE ALMOST LIKE THE BRUSH BAR IS WOBBELY NOISE IS WORSE WHEN IN CARPET MODE NOT ON REG FLOOR\015

Answers :

You will probably have a faulty roller bar take of panel on bottom of vaccum. Now remove the roller bar hold the bar by both ends and try spinning. This should be easy and smooth if not pull off the end cap these will be very tight and check the bearings in each end i think you will find a few small metal balls rolling around inside if this is the case you need to replace the bar
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

LOUD GRINDING NOISE ALL OF A SUDDEN , LOOSE BELT ?


You will probably have a faulty roller bar take of panel on bottom of vaccum. Now remove the roller bar hold the bar by both ends and try spinning. This should be easy and smooth if not pull off the end cap these will be very tight and check the bear ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.


... Windsor VS14 Versamatic Bagged Upright Vacuum

When I vacuum w/ the brush control in the on position it make a really loud noise, almost like a grinding sound. I have looked at it and nothing seems to be wrong, but I notice that the pin that engages the belt seems to vibrate a bit, possibly creating the noise. It started when I accidentally got part of a plastic grocery bag caught in the brush. Could it have stretched a belt? Nothing is caught any other place and it only makes the noise when the brush in in the on position.


Yes, the belt could have been stretched and is now vibrating and hitting other parts and creating a noise if much of the bag got caught under the belt. If you have another belt for this vacuum, please put it on and see if the noise stops. If it does ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

Loud noise?? my vacuum suddenly just got really loud. it suctions fine, i changed the belt, but when the roller is off its not loud, but when i put it back on the 11noise is horrific. it vacuums fine i just cannot stand the noise. please help


I have the exact same problem. I've taken the thing apart and cannot figure out what is causing the noise. It's not the belt and it doesn't seem to be coming from the engine. It sounds like the spinning brush is hitting something, but it's not, th ... Bissell 6590 CleanView Bagless Upright Vacuum

Makes a loud noise like a grinding noise then smokes comes out and it smells like burning rubber? When I take the (rod) brush off with the belt then run the vacuum there is no more noise? Please help me thank you


Your belt is worn and stretched and so it is slipping on the motor drive shaft. That is why it is noisy and smells like burning rubber. You simply need to replace the belt. You can get replacement belts here: ... Vacuums

Bissell model 1694 rug scrubber works for a while then makes a loud noise when you pull it toward you like it is. Umping over something, roller is very easy to pull on, is it loose or a belt?


Dear Sir:Possible the motor can be faulty, or test the belt if is crack and replace. However you must see if there are some debris inside. Please see the section troubleshooting in your user manual. Download Biseel.com or www.fitness.manualsonlin ... Vacuums

Loud noise I ran over a string and then shut it off quickly. It now makes a horrible grinding sound. Did I ruin the motor? Sounds like something came undone. I checked the belt and that is fine. Ideas?


I think you damaged the belt. I ran over a sock once and it made a grinding noise but still worked for several months after the incident. Finally, the belt broke off. I had it replaced and now it doesn't make that sound. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I was using my Hoover Steamvac model F5815 today when before I finished it made a loud noise and something came loose inside with it giving off a burning odor. I don't even see how to open it to check on a belt or whatever. Any suggestions? Thank-you


... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

My Dyson dc-07 makes a loud grinding noise only on the carpet setting.The belt seems to be fine,and the brush spins normally.Do I have a potential clutch or motor problem?


... Dyson DC07 Bagless Upright Cyclonic Vacuum

Loud Grinding Noise


Jhu ... Hoover V1 SteamVac SpinScrub Vacuum

LOUD noise Turned on vacuum one day and it made a reallly loud noise like the belt had broken. So we replaced the belt correctly, and turned it on and the noise is still there it is also rattling violently. HELP PLEASE not exact same model but close enough


The armiter or fan is broken and if you get it replased it should work like new ... Hoover U5227-930 Elite Upright Vacuum

I replaced the belt on my Dirt Devil Featherlite Bagless Vacuum and the brush roller rubs and makes a very loud noise when turned on. I have gone exactly by the manual instructions and made sure the belt and end caps were on correctly, but the bristles still rub the back and it makes a very loud noise. Without the brush roller in the vacuum, it sounds and runs normal. What could the problem be?


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=561283\015\012Generic problem for all Vacuums\015\012I replaced the belt on\015\012Posted by piggyt ... Vacuums

My Bissell Cleanview Bagless vacuum makes loud grinding noise.


The ends of the roller have something wrapped around them.see if you can pull the ends off so you clean the caps and bearings ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Cleartrak vacuum suddenly cleartrak started to make weird loud noise i cleaned. When it got jammed I stopped the vacuum and dislodged the jam and it worked fine. How to stop the weird loud noise?


... Vacuums

Loud noise I have a Shark UV610 model of the Cordless sweeper. All of the sudden there is now a loud noise when I turn on the power to vacuum. Any suggestions?


... Euro-Pro Cordless Bagless Upright Sweeper - Blue/Gray

Noise Hi... I was doing normal house work and had been using it on carpet... I put it on floor for my hardwood floors and picked up loose clean cat litter and went to put it back on carpet and it made a horrible noise like it was rubbing. cleaned the filter... cleaned the roller thingi ...checked the belt and it is still making that horrible noise. It does not make the noise when I have it on floor but as soon as I put it on carpet it screams at me. Help! Please and thanks Linda


Hi Linda,\015\012Sounds like clutch problems, try to move the lever for carpet/floor back and forth a few times maybe it will free up. If it still makes the grinding noise, the clutch assembly will have to be replaced. Let me know, i can even ... Dyson DC07 Bagless Upright Cyclonic Vacuum

A loud grinding noise happens in the tilted/unlocked position. This noise can be heard when running over the fringe of an area carpet. What causes that noise?


Hi there it's SmartAlec from NelsonVacuums.com.au here. It is the clutch of the brush activating. It is designed to stop the brush from chewing up curtains etc. If it is to ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My Hoover Wind Tunnel Bagless Pro Pet is making a very loud thudding noise when the belt rotates, belt seems to be intact and in place, what am I missing? Vacuum is less than 6 months old, belt is not worn and motor seems to be fine.


... Vacuums

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o


Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

I have a Model U57809RM Hoover Cyclonic which started making a very loud noise. Changed both belts on it but the noise persists. It seems to happen when I put the handle in the 'engage to vacuum' mode. The minute I start to lower it the noise begins. Help!


Hello,You could have a broken fan in the motor and need to replace the fan. If the noise is coming from the brush area of the vacuum, you probably have a broken bearing in your brush roller and would need to replace the brush itself. ... Hoover Vacuums

There seems to be a wheel that holds tension to the belt which came off. Now the belt spins and makes a grinding noise. I cant figure out how to get to the belt? Any one have advice?


I can help you a lot further if you can send me a picture of the bottom side of the vacuum. My email is [email protected] Once I see a picture this will help me tell you how to fix it. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dog hair gets caught all the time in the belt drive spool, is there a fix for this other than having to pull it out all the time by hand? I have replaced the belt and the brush but this hasnt solved the problem and the belt moves so slowly and I get the loud whining/grinding noise too.


It could be either the clutch, the beater bar or the brush housing. I have included links to each parthttp://platinumvacuum.com/dyson-dc07-dc14-clutch-assembly-900252-04.htmlhttp://platinumvacuum.com/dyson-dc07-dc14-brushbar-assembly-9041 ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My eureka vacuum was fine but then suddenly got loud. We cleaned the filters and replaced the belts, but it is still loud. We have not seen any clogs in the tubing or in the vacuum. What other problems could the vacuum have to make it loud?


The noise could be coming from the Beater Bar's ball bearings. ... Vacuums

Belt wont turn makes a loud noise when put on carpet setting


If this is a Dyson with a protected belt that can't be replaced then it will have to be sent out to Dyson or get a Dyson servicepersonnel to check it over - protected belt motors are difficult to fix by yourself. If its clicking all the time, then it ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Loud noise and appears the belt is slipping


The belt stretches and becomes loose or missing some teeth replace the belt. dub_mccorkle@!yahoo.com ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0470 seconds