Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

Bin bottom release snapped off. How do i open the bottom?

\015 The bottom of my cyclone bin will not open as the release catch has snapped off and i cannot work out how to take the bin off! any ideas???\015

Answers :

Take out the three screws on the to near the handle inside you will find the remains of the old part you can either replace the old part from the top and put it back together to open it normally or you can use the old release stick to push down the catch at the bottom if you decide to replace the part make sure the release stick is in the centre through the 2 holes its very tricky
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bin bottom release snapped off. How do i open the bottom?


Take out the three screws on the to near the handle inside you will find the remains of the old part you can either replace the old part from the top and put it back together to open it normally or you can use the old release stick to push down the c ... Dyson DC07 Bagless Upright Cyclonic Vacuum

On the DC07, the entire cyclone assembly must be removed to empty the dust, debris, etc. collected when vacuuming. On the top of the cyclone is a "trigger" that you lift with your finger to release the bottom catch, which allows a clear flap to open on the "clear bin," thus letting all the debris fall out. My problem is when you lift the finger trigger, it does not release the catch on the bottom. Since the catch won't release, I cannot remove the entire clear bin either from the cyclone.Any sug


Beofre you go to the extent of buying a replacement canister, you can remove the top and using a straightened coat hanger type thing open that bottom lid. Then maybe you can clean the rim and possibly add some silicone spry to loosen things up. Here' ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I HAVE A DYSON DC07 PINK VACCUM -DON'T KNOW HOW TO OPEN BOTTOM TO RELEASE THE DIRT??


... Dyson DC07 upright vacuum - pink

Dyson DC07 Clear Bin Flap will not release


Important thing is that in order to get the rod in the hole, you have to squeeze the trigger while you are trying to do it. Squeezing trigger makes rod longer. All fixed! ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I don't know how to open the bottom to release dirt


You can get an owners manual here: Dyson DC17 user guide and owners manual ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Cant get the bottom lid of dyson dc7 dirt bin to open


Hi there,I am sorry to hear you are having difficulty opening your clear bin. The mechanism that releases the bin base is actually part of your cyclone assembly. When you pull the trigger, a small clip at the bottom of your cyclone releases t ... Dyson DC07 Bagless Upright Cyclonic Vacuum

On the dc07 Animal ,when the release trigger is pulled to allow the rubbish to fall out of the bottom of the shroud the flap does not open being jammed shut


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a Dyson Animal upright (purple). I took it apart to clean the cyclone chambers. When re-assembling the bottom closed before the opening rod was inserted. I can't get the opening rod installed with the bottom opening closed. How do I open it? Thanks.


I looked in our DC07. I would try removing the top again and getting a long dowel or the opening rod, insert it down into the unit and PUSH. The opening rod opens the latch by pushing it, not pulling it. Here are some pictures of the latch. Top pi ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Dyson DC07 bin falls open


You can replace the lid ... Vacuums

Pulling up on button will not release bottom of cannister.


The gasket is sticking to the dump lid. While holding it over a waste receptacle, operate the release button and pull the waste gate at the same time. Rinse the canister and dry thoroughly. Apply a spray of silicone to the gasket surface, let it s ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.


... Hoover Tempo Widepath Upright Vacuum - Blue

My dyson animal's clear bin latch is stuck and won't release. I can't take off the bin via the outer shroud release either.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Manual I realize it's probably something simple but how do I release the Cyclonic Chamber on top of the Dust Cup lid? I see the red 'open to clean' release button but how do I get down in there to push the release button? Thank you in advance for your help! Best, Christy


Manual > http://www.sharkclean.com/manual/NV22-NV22C-NV22P-NV22T-NV22Q_REV_1008.pdf ... Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum

Dear Sir or Madam, I own a black 23 x 47 x 7 mm Rowenta lighter. It has a screw on bottom that I cannot remove. What is it hiding ? Is this lighter refillable ? Is there a flint to replace ?. I've found on your site the following : "By jbbiii on Apr 06, 2009 Father died and left me a Rowenta lighter purchased in Stutgart in 1952. It has a screw on bottom with spring to replace the flint, but I cannot figure out how to open the bottom to replace the cotton wadding which I can see through the hole


Hello \015\012The flint should be near the striker.Or the thumb roller,usually below it.\015\012As old as it is you may not see it beacause its worn down.\015\012\015\012Maybe taking it to an antique store or a smoke shop woul ... Vacuums

My Dyson DC14 Animal doesn't have the suction it used to. The piece in the back on the bottom - a flap it appears - stays open now, causing the machine to make a louder noise than usual. At first, if I put my hand on the flap opening it would close, allowing for normal suction. Now, it stays "open" permanently", causing the loss of suction.


Hi its Darran at Dyson.Having had a look at a DC14 here, I am unsure as to the part you are referring to. So that we can help you further, please contact our Helpline free on 0800 298 0298, between the hours of 7am - 10pm, 7 days a week. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Hoover Z400 bottom half will not release and unfold to an upright position


... Hoover U9125-900 Z Bagless Upright Vacuum

The base of the clear bin won't open.


Just had the same problem. Finally realised what to do. Pull the long rod away from the top against its spring (by the rubber gaiter) and whilst holding it, undo the screw holding the long rod to the top trigger mechanism. Now you can wiggle the rod ... Dyson DCO7 Animal Bagless Upright Cyclonic Vacuum

Dyson, pressure release valve keeps going off and staying open.


There are a couple of things you can do, the blled valve (pressure valve) activates when there is a blockage in the machine. You just need to find the blockage:\015\012\015\0121) To check for blockages from the bottom of the machine. Remo ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Bin will not open, seems stuck.


... Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum

I have a bissell quickwash 1950-e. I bought it Jan. 2006, and have only used it 8-10 times, I live in a very hard water area, so I though if I put some vinegar in with the cleaning solution it would get rid of any hard water deposits, unfortunatly the solution went lumpy in the tank and stoped spraying out water, I have opened it, hose clean, sprayer not blocked, x at bottom of water container when depresed water trickles out, component that opens the x when water container placed, also ran wate


Hard to say what is causing your problem, replacing the cap and insert on the water tank may help, part #2041111, even tho it may trickle out water when depressed, they can still be bad. The other thing would be the rod not relesing the water like i ... Vacuums

Doesn't work Our home was built and finished in August 07.  The central vac doesn't work.  There is supposed to be a slot that opens in the kitchen where you sweep the dust and it sucks it up.  Also, the mounted unit on the garage wall has a hose that goes up into the house but there is a hole open at the bottom of the unit.  Where can I get someone to help us?  Or, is there an installation manual I can download to see if the builder did it properly.  He stole our solar heater for our pool and s


Has the slot in the kitchen (VacPan) been installed? Or is it just not working? There should be tubing coming into the unit in the garage, and possibly another piece to exhaust the unit to the outdoors, although this isn't always necessary. The intak ... Electrolux Centralux Vacuum

Chassis hook broken to rod which controls release of liquid shampoo in Hoover steam cleaner. It is the back of the handle area that is snapped off, not the actual rod with "push on / release"


If it is part of the handle, it breaks inside alot, part number 39458006. #2 in the picture.\015\012 \015\012 ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Dyson DC07 cyclone release catch will not click (lock) back into position after removing the clear bin assembly to empty the bin.


... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Neotec XJ-2000 ionic air purifier. On the bottom of the device, it says I should open the casing and take out and clean the dust filter every month. I haven't done it in years and no longer have the manual. How do I open it up to get the dust filter out?


... Vacuums

Im trying to replace the cloth bag on my Kirby G6. How do I release the belt that holds the cloth bag at the bottom of the assembly? It is grey and has teeth that grab when tightened on the bottom of the unit.


Kirby G6\015\012Im trying to replace the cloth bag on my Kirby G6. How do I release the belt that holds the cloth bag at the bottom of the assembly? It is grey and has teeth that grab when tightened on the bottom of the unit. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0423 seconds