Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

Loss of suction on carpets

\015 My Dyson is the best vacuum ever - however it doesn't have nearly the proper suction when I use it on carpets, as it did when I first bought it. The beater bar turns, I have checked all areas for clogs, etc, I cannot seem to tell what the problem is. There is excellent suction from the wand. Can anyone give me some advice on what else to check for? Thanks alot!\015

Answers :

Wow...this is one of the only "bad suction" examples I have seen. I do know that after I clean my DC07, I have to make sure that the adapter pieces are seated properly, otherwise there's an air gap.

Have you tried connecting the hose instead of the main part? Is suction still bad? If so...then it's the motor. If not, then go back to check the adapter pieces or see where there's a blockage...look harder.

Call Dyson...their support is terrific!
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Suction loss when handle is tipped back to clean carpet


Ours did the same thing. I cleaned the filter and canister thoroughly. It needed to be cleaned, but that didn't fix the problem. I removed the plate under the carpet brush bar (three quarter-turn screws) and removed all hair, lint and threads from th ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a Bissell Proheat steamer carpet cleaner. There is a red L shaped part that says hips on it that I do not know where it goes. It also does not have any suction. Is the part the cause of the loss of suction and where does it go?


Http://thefuntimesguide.com/images/blogs/bissell_water_container.jpg ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

When using my vacum upright its very low in suction, it used to be so powerfull that it lifted my carpet slightly....when using the tools section its as strong as it should be please help, ive cleaned it out but still loss of suction in upright position, from mrs richmond


Check the following items:\015\012\015\012* The bag and connection - change it if it's full\015\012\015\012* Turn the vacuum over and inspect the beater bar area for any clogging. You may have to remove the bottom plate to ... Vacuums

Loss of suction on carpets


Wow...this is one of the only "bad suction" examples I have seen. I do know that after I clean my DC07, I have to make sure that the adapter pieces are seated properly, otherwise there's an air gap.Have you tried connecting the hose inste ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet


Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn't blocked as well. ... Vacuums

S7000 my miele upright vaccum cleaner looses it suction when on carpet mode, suction is perfect when upright (hose). The suction lasts for appox 5 mins when on the carpet and it stops.


... Miele Vacuums

Suction problem my proheat wont suction water out of carpet,,, it made a mess of my carpets now, any one no how to fix the suction problem?


The valve on the bottom of the water bucket is not being pushed up enough to allow the vaccuum to go through. Perhaps a part is missing but I used a small ball bearing and a car vaccuum cap to build it up and now our works but it is still a piece of ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Suction loss? loss of suction in hose/attachments so not able to get to small hard to reach places. Suction not appearing to work right through hose?


Hi samdan... have you checked all the hose attachment vents .. ie Under the vacuum as well... How long is it since you replaced the filters?\015\012\015\012Try giving the Yellow cone inside a blow out. these tend to become clogged from ti ... Dyson DCO3 Absolute Bagless Upright Cyclonic Vacuum

Loss of suction bissell vacume


Under the red flap in the water resevoir, there is a small screen. Pop that screen out and clean it. It is probably blocked with hair. I took my entire machine apart trying to fix this problem and I finally saw that screen. I cleaned it out and my ma ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

How to for Belt replacement and solution to suction loss


It is simply your belt - replace it.\015\012\015\012The suction you said is fine with attachments, so the belt is not turning the carpet brush ... Vacuums

Sudden loss of suction.


Check the inlet down by the brush roll to see if it is clogged. Also check the belt to be sure it is ok. Is there suction at the hose? If not then it is still clogged. ... Kenmore 33721 Upright Vacuum

My Bissell Proheat Turbo has poor suction and leaves the carpet too wet. Is there a way to improve the suction so the carpet will be left just damp not soaking wet?


Flip the unit over you will see a grey panel that looks like a V with 6 or 8 screws remove it and you will find a black cover I think it has 2 screws remove it and you will see a gasket seal for the bottom for the motor mine was white some times ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Loss of suction


How did you get the cap out? ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Su2914: loss of suction even when cylinder is empty!! doesnt work correctly when pet attachment is added either, only seemed to work ok for first 4 months then loss of suction, will pick up eventually but quite poorly! Should I take it for a service? Thanks


... Samsung Vacuums

Suction only works using the hand held mode, there is no suction when try to use on carpet mode,


There must be a clog in either the hose, dirt inland by the brush roll, or bad filters. If you have suction at the end of the hose, then look lower all the way to the brush roll. ... Vacuums

Poor suction...continued Wow, thanks for answering so quickly! To answer your question, yes, there is suction at the screen, but it is very weak. I keep that screen clean. As a side note, I noticed that when I remove the top clear plastic cover (that would be part # 37 on the diagram, as far as I can tell) there is decent suction coming from the intake there--part 36? 30? it's hard to tell. But with the cover on, I feel no suction (from where it sucks up the water directly from the carpet),


Wish I had it in my shop, it is hard to figure your problem. I do know that you must have something out of place and you may have to take it apart to find it. You may feel some suction there at the top of the clear nozzle, but maybe it isn't strong ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

Hoover Model# U8185-900 Problem: No suction, not engaging Vacuum cleaner roller spins as usual, but there's no suction when trying to vacuum the carpet. Can anyone point me in the right direction? Tha


... Hoover U8185-900 Upright Vacuum

Loss os self propel and suction??


Mine does the same thing. There is no suction. I found that there is a door that opens when you tilt the handle in the down possition. I think there should be a spring in place so it can open. Until I find a replacement spring I have to open the ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Power Loss - Suction Loss


HiIts cutting out because its overheating.Change the filters and check the base and the hose for blockages ... Dyson DC07 Bagless Upright Cyclonic Vacuum

No suction My vacuum does not seem to have much suction when in use. The agitator brush is rotating but I'm not able to get much off the carpet. The suction is fine when I use the attached wand.


If the belt is stretched, then it can't turn the brush rol under load, if you haven't chenged it in the last 6 months, then I would put a new one one. Also check the dirt inlet by the brush roll for a blockage. ... Riccar 8955 Upright Vacuum

Suction vacuum one day fine next not having great suction picking up big things but not feeling that deep down suction rolling too too easy changed bag, belt and cleaned roller it is like it is gliding over but not really getting deep visible cannot even tell I went over carpet


Don't panic! Easy fix!\015\012\015\012I was having the same problem, but I removed the base plate from the bottom of the vaccum (5 screws on mine), revealing the roller and the engine. Just behind the roller is an intake tube. Mine had ... Oreck XL Ultra Bagged Upright Vacuum

WHEN I PUT THE MACHINE ON TO CLEAN TH CARPET THE WATER DISPENSES INTO THE CARPET AND THE BRUSHES do not SPIN and theres NO SUCTION TO REMOVE THE WATER FROM CARPET


Make sure the lower tank lid is on securely, clean the intake filter on the top right of the machine. ensure the front panel is installed (the square to remove for hoe use). this has to be in place for carpet operation ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My Bissell spot bot does not **** the cleaning fluid out to the carpet. It has suction from the carpet to the machine but not from the machine to the carpet?


... Bissell 12005 Spot Bot Handheld Vacuum

Decreased suction was using to vaccuum carpet and suction decreased..nothing plugging hose....suction remain at unit canister and exhaust is fine....suggestions??


You might have a clog, to try and unclog the lines, you need to unplug the unit, and remove the bag compartment. Then take a shop vac using the hose attachment hold it into the attachment door where there is low suction and try to draw the clog out t ... Broan-NuTone CV353 Central Vacuum

Loss of suction when using upright. Suction remains for samll tools no suction when in upright position makes funny noise but ok when not used in that position kindest regards louis


U can remove the flexi pipe by pressing the inset button,it may be bit stiff if it had not being removed before.may be something is stuck at the bottom,also remove u bend where most of the stuff get stuck. i just posted how i fixed the suction and ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0567 seconds