Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

Can't lower beater bar - so won't pick up lint

\015 The front part of the head will not get low enough for the beater bar to pick up lint. We can't figure out how to lower it - HELP!!! (Thanks!)\015

Answers :

The small tube under the hover goes stiff and the beater bar wont go lower enough so youve got to get small tube under hover soft and than set beaterbar to the ground let it go hard and may solve your problem many thanks nick...
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Can't lower beater bar - so won't pick up lint


The small tube under the hover goes stiff and the beater bar wont go lower enough so youve got to get small tube under hover soft and than set beaterbar to the ground let it go hard and may solve your problem many thanks nick... ... Dyson DC07 Bagless Upright Cyclonic Vacuum

When the dyson is turned on the suction goes to the wand when you tip the beater down you do not have as much suction you cant pick up lint.


The Dyson system is designed to operate the hose with the handle in the upright position. When the head is tipped down (floor vacuum position) it closes the opening to the hose/wand ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My dyson animal is hard to push on carpet - the beater bar is still operational. When I turn off the beater bar and run the vacuum on hardwood the beater bar stops moving, but it still ''rolls'' on the hardwood - it doesn't pull up like it used to. It also seems to not be picking up as well as it used to, although no blockages are present and the filter is clean.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Our Dyson upright vaccumms beater bar wont move. the vaccumm will **** up air but the bar underneath wont move. The gears are not working property.


It could be the clutch that's causing the problem or the belt. Bring your vacuum to a local repair shop and have it look at, but it sounds like it could be either one of those problems. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My beater bar is not turning so the vaccuum is not picking up. The belt is not broken. The motor is working and I can see the cyclone effect in the canister. I have checked for blockages. I have cleaned the hair and string from the beater bar brushes. What should I do?


You need to replace the belt, it has probably broken. Your actually supposed to change them yearly. Here is a link to\015\012the belt you need and a manual with instrutions: ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have just purchased two (2) Electrolux Nimble vacuum cleaners. Not one, but both, straight out of the box, the beater bars will not run. It turns on, select carpet, and lower the handle, the red light to check beater bar/or filter lights up. You can reset the light by unplugging the unit, then plugging it back in, but with same results. Now the kicker, if you take out the handle, select carpet, lower the body by the carry handle, it will run and operate correctly, however, as soon as you r


... Vacuums

Beater Bar The "Beater Bar" or roller with brushes on it, is not spinning, therefore not picking up. I cannot locate my manual and need to know if it is belt driven and how to get at the belt to identify the size and purchase and install a new belt. Thank you for any assistance. [email protected]


Take off the bottom plate, then you can get to the brush roll and belt, on the model number plate, the number of the belt is on that, it is also on the belt if you can still make it out. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?


Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My filter queen just had the motor rebuilt last year and was basically a brand new unit when I got it back. It is not picking anything up now when I vacuum. The beater bar on the carpet attachment is turning fine and when I take all the attachments off the hose I can feel the suction being created like it should be picking up debris just fine. I have emptied the canister even when it did not have much in it; however, it still will not pick anything up off the carpet. It picks up debris tempo


It sounds as if you have a clog inside the "Power Nozzel". They mention that there are "no user serviceable parts within the Majestic® Power Nozzle" My advice would be to see if you can see a clog with in reachable distance and try to remove the ... Filter Queen Vacuums

Beater bar on Dyson upright won't turn when handle is lowered


I have finally fixed my sister's dyson dc 15 beater bar problem. It was just 2 tiny broken wires connect to circuit board lead to the beater bar. The wires broke where they go through the black rubber gommet. You need a torx ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

The beater bar wont rotate when set to floor cleaning on bissell aromatic carpet shampooer


... Bissell Vacuums

Beater bar on Kenmore model # 116.25615506 wont got on. Belt is fine.


... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum

I have a Dyson 15 "the ball". The beater bar will only rotate if the vacuum is engaged and the handle at a high angle. The bar stops when I drop the handle to a lower position. The condition is repeatable. Can you provide part and repair instructions?


If air is leaking in somewhere, you will not have any suction.\015\012\015\012\015\012Also there are some possibilities that has to be checked to confirm the fault.The problem is minor but the possibilities are too much for this pa ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Hello. i only have one arm and am trying to figure out why my beater bar wont turn on my dyson dc14. the belt smells a little too. thanx, trixie


Sounds like the beater bar is frozen in place. This sometimes happens when the ends of the bar become stuck in the holders.\015\012The solution is to remove the beater bar and clean the small holders on each end removing any debris that has built up ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The beater bar will not turn. I have cut all the hair and lint off but it still will not trun.


Is the belt broke ? also try taking the beater bar off the vacuum and then checking the end roller bearings. clean and lubricate with some light oil. make sure belt is solid. ... Vacuums

My beater bar is not going round, machine is not picking up I have checked for blockages and everything seems OK


The belt that drives the roller may have broken and reqiures replacement. You need to take the cover off underneath and remove the roller. ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

The beater bar wont turn and is breaking my belts


You might have the wrong belt size. ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum

My vacuum has not been running right..the beater bar is not picking up and the rollers aren't spinning...the belt doesn't need replaced so what else could it be...everything else seems to be running fine???


The motor shaft that spins the belt may have hair wrapped arount it, causin the belt to slip. You can't miss the burnt odor.\015\012Remove the belt and clean the motor shaft. ... Vacuums

The vacuum turns on but wont run smells like burning rubber I took the bottom off and the belts dont appear to be broken but the one connected to beater bar seems like it may be loose


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=542493\015\012Generic problem for all Vacuums\015\012The vacuum turns on but\015\012Posted by mmetcalf on Apr 24 ... Vacuums

I HAVE A DYSON DC07 I HAVE CHECKED ALL HOSES AND PLASTIC ATTACHMENT SECTIONS , CANNOT FIND ANY BLOCKAGE ANYWHERE IN THE SYSTEM .THE BELT IS GOOD AND THE BEATER BAR IS ROTATING WELL , BUT THIS VACUUM WILL NOT PICK UP ANY THING. I DID NOTICE THAT THE HEPA LIFETIME FILTER IS BLACK AND NOT SURE IF IT CAN BE WASHED OR CLEANED. THANKS BOB!


I have just cleaned mine just a half an hour ago - SAME PROBLEM !!\015\012ok take the dust cylinder off the vacuum cleaner and take the plastic clear cylinder off - there is a clear clip one side and you might need a small knife to unclip other ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My Dyson upright is not picking up like it used to. The suction from the tools is very strong and the beater bar is turning and clean. Please help


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

How do I replace belt on hoover s1147 twist & vac? I know it goes on the middle of the beater bar but I cant see where to attach the other end to.


... Hoover S1147 Twist Vac Handheld Vacuum

My beater bar will not spin when the handle is lowered? But there's suction thru the hose when the handles upright


I had the same problem. I read, earlier today, that one of the "problem solvers" called Dyson. Dyson suggested, with the Dyson upright and plugged in, on a carpet, toggle the "bare floor" / "carpet" knob from bare floor to carpet 5 times, then lay ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

My Panasonic performance plus platinum vacuum cuts off and on while using the beater bar, this doesn't happen at all using the stair cleaning attachment. It appear electrical contact is being lost where the lower plug makes contact.


The solution to my problem which is located at the lower electrical plug on the long wand was to expermint using a nickel and placing this in an area where the long wand connects with the beater bar section, here there is a gap which allows too much ... Panasonic Vacuums

Hi. We have a Riccar N2100 vacuum cleaner, which has served us well for many, many years. I'd like to attempt a repair on this unit, and looking for advice and/or a parts diagram to proceed. The unit makes a groaning sound when shut off. The sound tapers off in pitch as the motor and beater bar come to a stop. The sound only happens when the vacuum cleaner is turned off in the normal upright position. The sound does not happen when the lower unit and main housing are both laying flat. I took


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0535 seconds