Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

Can not get the beater bar seated back into position need diagram

\015 Seating the beater bar\015

Answers :

\015\012make sure the belt isnt tangled and the brush bar has to be seated into foot plate correctly before soleplate will fit,check the ends of the brush bar and you will either have 2 x little brush stumps on the ends and in which case there will be slots in the footplate so that the brush sits in correctly or you will have a brushbar that has small grooves on the ends and to which sits in footplate.simply turn brushbar by hand until brushbar sits into foot plate correctly then attach soleplate by putting front end in 1st then lock it. if photos are required for furtehr help please email me at [email protected]
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Can not get the beater bar seated back into position need diagram

Hi,\015\012make sure the belt isnt tangled and the brush bar has to be seated into foot plate correctly before soleplate will fit,check the ends of the brush bar and you will either have 2 x little brush stumps on the ends and in which case the ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?

Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I had a shoelace get stuck in the beater bar. I turned it off, tipped it over and untangled the shoelace from the beater bar. When I plugged it back in the vacuum ran but the beater bar was not turning and there wasn't any suction. Is there a reset switch for the beater bar? Thank you for your help, Janet

Hi Janet. there is a small reset button on the outside of the head next to the brush that you can push to get it to start spinning again. ... Dyson Ball DC24 Bagless Upright Vacuum

I purchased a Eureka C4910 last year and have a question that I am hoping you can answer. There are two motor actions with this vacuum, 1) the vacuum suction, and 2) the beater bar. The action of the beater bar is that motor is supposed to automatically shut off when the handle is in the complete vertical position assuming the vacuum is stationary, but then turn on when the handle is tilted toward the floor, assuming the vacuum is moving back and forth. The beater bar motor turn-on mechan

Good day!Normally when the motor is easily moved back and forth means that it have a proper lubrication,proper alignment and no clogs.When the motor and the belt is OK the problem could be on electrical wiring and switch ... Eureka C4910 Bagged Upright Vacuum

Took apart my cleaning brushes and all on my bissell spotbot i need diagram of how to fit the head part back to the machine. I had a problem with the auto not working i have fixed that problem just need to see so that i can get it back togoether. I assembled the whole wheel back but cannot caonnect it to the machine LOL

... Bissell 1200A SpotBot Pet Robotic Vacuum

The beater bar switch on my dyson 24 gets stuck in the off position. I have to push it many many times before the beater bar engages. How can I fix this?

... Dyson DC24 All Floors Vacuum New Upright NEW

Correct position of beater bar on a Dyson DC14?

I had the same problem. I removed the brush from the machine. The brush should move freely when removed. If it doesn't move freely, pull the ends from the brush, both ends come off(one will have a rod fixed to it). I would suggest you clean the ends ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?

Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest

I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum

Beater Bar The "Beater Bar" or roller with brushes on it, is not spinning, therefore not picking up. I cannot locate my manual and need to know if it is belt driven and how to get at the belt to identify the size and purchase and install a new belt. Thank you for any assistance. [email protected]

Take off the bottom plate, then you can get to the brush roll and belt, on the model number plate, the number of the belt is on that, it is also on the belt if you can still make it out. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


Is brushes moving, if so it is clogged , usually takes a star bit to take apart to clean ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Need to get to the beater bar

Hello,You're in luck! I actually just finished up writing a repair solution for this exact problem! Just like I said in my previous answer, you may want to try pushing the reset button first, especially if the power nozzle will not make ... Kenmore 25512/ 25513 Progressive Canister Vacuum

I have an electrolux epic series 2500 SR that is in pieces and I need to put it back together, I need to get a diagram to make sure it goes together correctly.

... Electrolux Vacuums

I took the brush out to clean it and cannot get it fitted back in. I need a diagram to ut it back together

May I get the make and model # of the vac to help you more. ... Miele S514 Solaris Electro Plus Vacuum

Canister Vacuum Cleaner - old Model 26412690 Serial #: DF3441912 I need a diagram of the electrical cord retrieval system. I have it disassembled and I need help getting it back together again.

Hello Nurburd !\015\012\015\012Go to the following link , here you will find the service manual for the 26412690 \015\012 ... Kenmore Vacuums

Help i can get suction from the hose but when i stick it in the back of the carpet head i get no suction and the beater bar will not turn. can you help

... Miele S184 Powerhouse Bagged Upright Vacuum

Can't get beater bar back on Dyson Animal - it won't set back into the machine correctly.

The bearing blocks must be oriented correctly. Take the belt off and put the brush in place. Once you have it in, mark the surface that is visible with a dot of white out, nail polish or marker, depending on the color of the block. Remove the brus ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Our DC 17 was making a horrible noise, so my husband took off the beater bar and was pulling out hair and a small, silver cylinder came out. We can't get it back in and realize it is what the belt is on. Any advice?

Is it a part of beater bar? Is that what your saying, If so you just have to order another beater bar, If you can send pic, it will help more. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n

From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums

I have the eureka boss 4495 widetrack and the end piece of the beater bar broke off. I guess I put it back together wrong when I put a new belt on. Where can I get a replacement part and will it work do you think.

Call the Eureka people (1-800-282-2886) and describe to them what the beater bar thingy that you broke is. Ask them if you can order that unit--if you think you can install it. Otherwise, ask them where to the authorized repair person closest to yo ... Eureka 4495A Bagless Upright Vacuum

The power to rotate the beater bar only works half the time..it seems to be very positional. In the past I could get it to work, now it just won't turn. Have tried the re-set button . Expensive vaccum with poor reliablility!

Is the power nozzle motor itself not working? If it's not, the problem could be the wiring, the switch, the vacuum power switch, the connectors from hose to machine, or the circuit board in the machine.\015\012My best guess would be the connec ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Hi. We have a Riccar N2100 vacuum cleaner, which has served us well for many, many years. I'd like to attempt a repair on this unit, and looking for advice and/or a parts diagram to proceed. The unit makes a groaning sound when shut off. The sound tapers off in pitch as the motor and beater bar come to a stop. The sound only happens when the vacuum cleaner is turned off in the normal upright position. The sound does not happen when the lower unit and main housing are both laying flat. I took

... Vacuums

I bought new belts to replace the old ones (one had broken and the water would not feed) My cousin took it apart and now I need to put the new belts on and get it back together - do you have instructions or a diagram?

There are different variations with Bissell. They have the ProHeat series and a Power Turbo series. Below is a link with instructions and diagrams for the Belt Access Door. If this doesn't solve your problem or isn't the correct model, please post ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I cannot seem to replace the beater bar on my Dyson - it seems to spin OK, but when I turn the vacuum back on and turn it to the 'Carpet" position, it makes a noise that is unbelievable. What's up with that? The belt is intact.

Sounds like its the clutch to me if it sounds like a rapid clicking and you have a large knob on the side of the cleaner head it is going to be the clutch this is a hard part to changed without the know how to do it and it is very easy to break the o ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I have an Electrolux Commercial Upright vacuum Model U129C. It has a device which turns off the motor driving the beater bar if something gets stuck in it. There is a simple reset button to restart the beater after clearing the obstruction. Just recently on flat dense low pile surfaces the switch cuts in after just a few seconds and turns the beater bar off. This doesn't happen on high pile carpet but the motor doesn't quite sound normal. There is no obstruction - the beater bar can spin freely

The motor is having a problem.There might be two reasons...either the coils inside it got heated up which will be needing rewinding or you can buy a new motor or there r capacitors attached sometimes u can make a check on that also if that's gone Kap ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1318 seconds