Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

Mrs Cleaner flex has pulled out how do I replace Electric supply wire to switch on handle has broken at switch. How do you remove switch to repair? tonysimmons


Answers :

Hi\015\012
\015\012\015\012\015\012\015\012\015\012dsc04925t.jpg\015\012dsc04924t.jpg\015\012\015\012This should go without saying, but the first step is to unplug the machine. Next, open it up and remove the bag.\015\012Now you will need to remove the lid. There are white plastic clips on either side that you must carefully disengage by pushing them towards the center of the machine. Click the picture above and you can see that the right side clip has been disengaged.\015\012\015\012dsc04923t.jpg\015\012dsc04919t.jpg\015\012\015\012Once the clips are disengaged, the lid can be lifted clear of the body. Note the thin black plastic tabs on the lid that insert into slots in the body. Set the lid aside someplace safe where nobody will step on it. As an aside, I have twice replaced the dust channel, the fragile black piece of plastic visible at the top of the lid. Fortunately it is not a terribly expensive part and it is very easy to replace because it is only secured by four screws.\015\012Go back to the vacuum cleaner body. The next step is to remove the air filter. It is secured by two fairly obvious screws. These screws also hold down the switch assembly, which we will remove in the next step. But for now, go ahead and remove the screws and lift off the air filter. Put it aside where you won't lose it.\015\012\015\012dsc04915t.jpg\015\012dsc04907t.jpg\015\012\015\012Here you can see that the air filter has been removed and we are ready to remove the switch assembly. At this point the only thing holding the switch assembly to the body is the electrical connector underneath, and a plastic pin or two. Get a good grip on the switch assembly and lift it straight up with a firm but gentle tug.\015\012This is the underside of the switch assembly after it has been removed from the body. The white rectangular electrical connector in the center mates to the black rectangular electrical connector in the body, seen on the next picture. Put the switch assembly in a safe place until we reassemble the vacuum cleaner.\015\012\015\012dsc05469t.jpg\015\012dsc04910t.jpg\015\012\015\012Here we see the body with the switch assembly removed. We're almost there. The next step is to remove five screws, one of which at upper left is hidden in a deep recess. Click the picture above to see the location of these screws.\015\012The five screws have been removed. Carefully flip the vacuum cleaner over so that the black bottom and the wheels are pointing up.\015\012\015\012dsc04909t.jpg\015\012dsc04906t.jpg\015\012\015\012Here it is, belly up. Nothing is holding it together at this point, so just lift the entire base (the big black part) off and set it aside. It is not necessary to remove the rubber bumper that goes all the way around the outside of the base. As I learned the hard way, It is difficult to reattach.\015\012The inside of the base is likely to be pretty grungy. You could clean it up a bit with a damp cloth (I did), but there are wires in there so I wouldn't get it too wet.\015\012\015\012dsc04908t.jpg\015\012dsc04902t.jpg\015\012\015\012At last! The Miele's  innards are exposed. The motor is at the bottom of the picture and the cord winder is at the top. Remove one screw securing the cord winder electrical connector and then disconnect the electrical connector. You may now lift out the cord winder and replace it.\015\012I was also having an intermittent electrical connection problem which I thought was related to the problematic cord. It turned out to be an unrelated problem with one of the electrical connectors in the center of the machine, pictured above. Part of the plastic clip designed to hold the connectors together was cracked. Unfortunately I did not have a replacement part, so for now I wrapped some electrical tape around the connector to hold it securely together. This seems to have done the job. But the next time something else breaks on this Miele, I will order this part too and replace both at the same time.\015\012\015\012Follow the instructions in reverse to put your vacuum cleaner back together.I hope you found my little tutorial useful.
\015\012
Remove the bucket from the front of the machine and the handle and pipe from the back on the front of the switch housing you will see a screw remove this screw on the back you will find two little catches one on either side push these with a screwdriver then the sides of the switch housing will pop out from the chassis now on the front theres another on the bottom of the housing push this down and pull the housing off from the front when replacing this part be carefull not to trap any wiring 
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Mrs Cleaner flex has pulled out how do I replace Electric supply wire to switch on handle has broken at switch. How do you remove switch to repair? tonysimmons


Hi\015\012\015\012\015\012\015\012\015\012\015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I want to remove the power switch on a dc04 to repair a broken wore, how do i remove the switch?


Go to www.dysonmedic.com then scroll to the bottom of the page and click on DC04 cable change. You won't get better advice anywhere (and I've got no connection with dysonmedic). ... Vacuums

Knob has broken where you remove dirt container. Also the handle . How can I get the container out and what will it cost for repair parts? Model # CP-CY4201E


... Kalorik Red Cyclone Vacuum Cleaner

The mechanical off/on in the handle is not working with the electrical on/off switch upon removal of the handle you can cut the machine off by hand but after ensuring the the handle is re-placed in the proper position the machine will not turn off so what new handle or is the rocker switch has worn is now to hard for the mechanical switch to operated


Hi there it's SmartAlec from NelsonVacuums.com.au here. You are spot on in your diagnosis however i have fixed heaps of these and i have found no way to tell wether its the ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Brushes stopped The brushes stopped turning while using the cleaner. I removed the brushes to see if the spindle was broken, it wasn't. I then removed the top plastic cover and checked the switch that engages the brushes; it didn't seem to be moving correctly. There's one spring on the switch - should there be two? Or do you think something has broken on the inside? Thanks for any help


Most likely the turbine is bad, it may just be clogged up, you can take it apart and clean it out real good. That may work, but it may not. Sometimes it is best to replace the turbine. ... Hoover F7431-900 SteamVac Vacuum

My Electrolux Epic 6500 SR will not turn off by pressing on the switch button. I took it apart and removed the switch assy. I can maunually turn it off & on by pressing the rocker arm on the switch assy. It appears that the problem is with the big blue operator button, not the switch assy itself. The button does not seem to press down enough to cause the rocker arm to switch. The button has a "U" shaped wire that presses on the rocker arm and it may have some broken plastic details at the b


WOW !!! Finally You are dead on, absolutely 100%.... good work!!!.Get only a genuine new switch button with spring from an AERUS Electrolux dealer and reinstall. Then carefully reassemble the entire body and wiring harness.Con ... Electrolux Epic 6500 Vacuum

How do you remove the Handle from the Hoover Windtunnel Deluxe to replace the switch?


Removing the handle assembly should be easy after removal of the two screws. It may be binding or hanging up on the self-propel cable...or the plastic may just be stuck/binding. Note that the handle slides in and out of the vacuum unit along the sa ... Hoover U5450-900 Windtunnel Supreme Bagged Upright Vacuum

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?


... Vacuums

Hoover floormate handle release pedal broken. Need diy repair information.


... Hoover Vacuums

How to remove broken handle release on hoover windtunnel upright


... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

The wand release button has broken. Therefore, the wand does not lock into place which results in swivelling of the handle and sometimes the handle coming off while using the vacuum cleaner. Can this wand release be readily repaired?


... Euro-Pro NV31 Infinity Vacuum

Switch repair/replacement How do I get to the switch to repair/replace it ? Have removed the small torx screw on the handle but to no avail.


... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

I bought the vac, used, but was told there was nothing wrong with it. I called the company, and was given the impression that it will be a huge headache to return it. Here's the best part: when I received it, I opened the box: it was broken. Clearly the highest internal piece of the vacume, whent he handle is removed, was cracked off, and in two pieces. The handle will not lock into place, so if I were to vacume forward, see ya, and the vac is back in pieces. Any idea how to rig this to get it t


... Dyson DC25 Vacuum

There is something stuck in the handle of my Miele vacuum. I unscrewed all the screws hoping that I could remove the hard plastic handle from the hose. I was only able to flip up a piece of plastic where the switch is. Should I pull harder to pry the plastic apart? I was afraid I'd break something. Thank You, Chrissy


... Miele Vacuums

My Electrolux Regency Series upright vacuum brush motor does not activate. Cleaned the brush and press reset to no avail. Opened handle switch assembly and checked each wire attached to all three switch settings. Tried disassembling brush assembly but could not pry open after removing all screws.


... Electrolux Vacuums

VACUUM REPAIR I have a Hoover Savvy upright, windtunnel, bag/bagless vacuum (model U8150-900). The Handle Release Foot Pedal - Part #38434026 broke soon after purchase but I finally found a source to replace this item. The problem is that now that I have the repair part I cannot figure out how to remove the old pedal and install the new one. The housing appears to be one piece of solid plastic. Any ideas, PLEASE! Peter


There are 2 tabs that stick out on the release, they fit in slots, so from the top look down and you can see them, using a flatblade screwdriver that will fit in there, push the side in to release it, which isn't easy, but it can be done. When you g ... Vacuums

I have an Aerus Guardian canister vacuum with a clogged hose. The tiny stuffed animal toy is lodged right below where the swivel handle meets the hose. Switching the air flow does not dislodge it. I would like to remove the handle from the hose. Any suggestions?


Consider this. If your vacuum is still under warranty, removing the hose will void the warranty on the hose. I strongly recommend calling an authorized dealer/consultant.\012Although it may seem to be fairly simple to remove the handle, there ... Electrolux Guardian Bagged Canister Vacuum

The ON/OFF switch does not work. Unable to turn off vacuum without unplugging from wall. After removing handle, the ON/OFF switch is in ON position, but cannot be toggled to OFF position. Please assist. Thank you.


Replace the switch. Part number 28161067 ... Vacuums

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless


Get over it and buy a new one!!! ... Vacuums

How to dismantle twin clean powerhead to repair broken wires? the wires to the pc board have broken but can't seem to be able to remove plastic cover over wires without breaking cover.


... Electrolux Twin Clean Bagless Canister Vacuum

My dyson slim vacuum doesn't switch from hose to floor mode. I thought the foot lever was broken. I realigned it but it doesn't switch now from floor mode to hose mode. I take out the hose and I can see the white part. I thought it should move as you go from upright to recline position of the handle.


The changeover valve is not activating - call the Dyson helpline - they'll set you up for a repair with a repair dealer in your area. ... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow

Broken Switch on Hoover Windtunnel U6474-900


Hi there SmartAlec from NelsonVacuums.com.au here. I have a U6445 but i suspect there is little difference. Mine has only 2 screws as well and it also was very stiff. After ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Electrolux Discovery II 1500c Upright Handle Switch Assembly


... Electrolux Vacuums

It seems the off/on switch is broken


Sounds like a Hoover, which you had given the model number. But there are 2 or 3 screws to remove the handle, then there are 4 screws in the tool compartment, open the filter door, then the tool comp. should pull out, the switch part # is40309 ... Vacuums

It seems the off/on switch is broken


Remove the tools from the front of the tool storage. You will find three screws recessed in there, two on the bottom and one at the top. Once removed, the tool compartment will slide out and the switch will be accessable. \015\012You should be ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0552 seconds