Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

Roller brush is not turning on a dyson DC14

\015 Can't seem to figure out how to take it apart to check anything inside The belt to the roller doesnt appear to be broken.\015\012\015\012I have a dyson dc-07 and the brush's bar will not turn.\015

Answers :

Http://www.dyson.co.uk/support/help.asp?product=DC07-SY&article=527
\015\012here's a link that might help
\015\012good luck
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Roller brush is not turning on a dyson DC14


Http://www.dyson.co.uk/support/help.asp?product=DC07-SY&article=527\015\012here's a link that might help \015\012good luck ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson DC14 animal vacuum does not turn on however the roller brush does come on.The hose was clogged and that was cleared but vacuum still will not turn on.


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Roller brush is not turning on a dyson DC14


... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Dyson DC14 It started making a high pitched squeel so I took the filters out and cleaned them and i checked all places that pull out on the vacume to see if there was anything clogged. I also cleaned the roller brush. but when I turned it on, after a couple of seconds the sound came back again. can you help


Sounds like motor bearings are gone .... sorry. ... Dyson Vacuums

Roller brush of my dyson dc07 isn't turning...


It migh be the belt.check your belt or it is the brushroll is stuck.(from to much hair ect.) ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson DC14 roller doesn't turn but everything else works. The belt is on correctly, the roller is clean and it turns manually so I can't figure out the problem.


The DC14 has a "brush control system" operated by a knob on the right side of the base. This knob has two positions: "bare floors" and "carpet". The roller will turn only when the knob is on "carpet", and even then only when the handle is tilted back ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Dyson dc14 brushes not turning - Dyson DC14 Bagless Upright Cyclonic Vacuum


Hi there, it's Jack at Dyson.I'm sorry to hear your DC14's brush bar isn't rotating. This could just mean that the brush control is set to 'Hard floors' rather than 'Carpets'. To check for this, please take a look at our Support guide: ... Dyson DC14 Bagless Upright Cyclonic Vacuum

Dyson DC14 Brush Bar won't turn


You don't need to take it for repairs, I just corrected the same problem on the phone with a tech. Have the head on your lap, make sure the end nearest the little belt has the rounded side of the bar facing you. The squared off end faces towards th ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My dyson dc25 just turned off while i was using it first the roller brush stoped turning so i used the hose and now it turned off and wont turn on how do i fix it?


... Dyson DC25 All Floors Bagless Upright Vacuum

Dyson dc 41 roller brush will not turn


Hi there,You can download a .pdf copy of the DC41 user guide directly from our website: http://media.dyson.com/do ... Dyson Dc 41 Ball

Dyson brush roller will not turn


Can be 1 of 3 issues \0121 bad motor head\0122 bad reset switch in the switch housing\0123 broken wire in fork that holds the ball 3 screws on side unscrew lift plate make sure both wires are intact ... Dyson DC07 Bagless Upright Cyclonic Vacuum

DC25 roller ball dyson brush won't turn


... Dyson DC25 All Floors Bagless Upright Vacuum

Dyson dc33 bagless roller brush won't turn - Dyson DC33 Bagged Upright Vacuum


... Dyson DC33 Bagged Upright Vacuum

Dyson dc14 brush bar is not turning at all. Everything else seems to be fine. I just replaced the brush bar but still no movement. What else could it be?


Hi there,I'm sorry to hear you're having difficulty with your DC14 Animal. If the brushbar doesn't rotate, please check you have the brush control set to 'Carpets', not 'Hard floors'. The brushbar will not rotate when the machine is standing ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My Dyson dc15 animal roller brush will not turn off when I push the on/off switch....changed the fuse but still will not turn off. Help!


... Dyson DC15 Animal Bagless Upright Cyclonic Vacuum

The brush wont turn on my dyson DC 14 - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum


Sounds\015\012 as if you need to replace the brush belt.JimLet me know if this helps. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a DC14 with a bad belt to the roller.How do I remove the clutch that operates the belt to turn the roller. I am holding the assembly that houses the clutch and all screws are out, it appears the red knob that engages the drive to operate the roller brush must be removed. Please advise and how. Thanks, John.......[email protected]


You need a special tool to remove the clutch. Contact the Dyson Helpline so that they can refer you to an authorized Dyson dealer in your area who would have such a tool and who can fix it for you. The alternative is to purchase a tool and visit YouT ... Dyson DC14 Bagless Upright Cyclonic Vacuum

Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.


... Hoover Tempo Widepath Upright Vacuum - Blue

How do we fix roller brush on dyson dc14 full gear?


Have you also checked that the brush control knob is set to "carpet"? The brush will not spin in "bare floor" mode. (Sorry if this seems too obvious to mention, but I see lots of Dysons where incorrect setting of that knob is the only problem.) Fail ... Dyson DC14 Full Gear Bagless Upright Cyclonic Vacuum

Kenmore Canister Vac, Progressive, 25512 255513 model. Brush won't turn. One end of the brush roller, end closest to belt, is off center which is keeping it from turning freely. The end cap is like a square. Other ends turns fine. Do these end caps come off? If so how? Can't get it to budge. This is exactly what is keep brush roller from turning.


Take a flat head screw driver and pry the end cap off. It will come off. You might have some string or hair around it causing it to not turn. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

I replaced the clutch in the dyson dc14. it isnt making that terrible noise anymore....thank god!! but the roller brush is not moving when the vacuum is in use. whats wrong?


The "horrible noise" you were hearing before wasn't the clutch! It was the roller brush. If the brush is not turning, all you are doing is burning out your new clutch. Reasons for the brush not turning: there is hair, carpet fiber or other matter wra ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Dyson DC14 brushes do not turn. Removed all hair and debris.


DC14s have two drive ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My Dyson DC15 has suddenly become very reluctant to turn left. This is only the case when it is switched on and irrespective of whether the roller brush is running or not. When the cleaner is switched off it behaves as normal as far as steering is concerned.There is no obvious problem with the ball or steering swivel mechanism. Any ideas ?


Hi its Darran at Dyson. Although strange, I believe we have a solution. It sounds as though the cleaner head hose is blocked. When the machine is running the suction will be pulling against the bloskage causingt he hose to contract and p ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Brush roller does not turn. - Dyson Vacuums


You need a new drive belt. you can get them here:www.vacbelts.com ... Dyson Vacuums

I have a dyson dc07 upright which no longer picks up lent and hair. The roller brush is not spinning when the vacuum is turned on. How can I tell if it is the belt that needs to be replaced or the clutch and belts?


Need replaced Clutch Assy and Brushbar \015\012\015\012Clutch Assy part no:900252-04\015\012\015\012Brushbar Assy part no:904174-01\015\012\015\012try cleaning all Hose\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0627 seconds