Having problems with your Dyson DC07 Bagless Upright Cyclonic Vacuum ?

I need more suction. The Head is too high on my carpet.

\015 We have owned our dyson for less than a year and it only worked well in the first few months. Something is off. If we manually push the head or front of the vaccume down to hug the carpet we get better suction.I am dissapointed, but will be thrilled to solve this, so that our new vaccume does its job. Please help.\015

Answers :

Hi.
\015\012
\015\012A slitght adjustment can be made by either screwing on short transparant internal hose on top of floor head tighter or undoing it turn.
\015\012
\015\012Do this on A table as you need to get down to be able to view sole pate movement
\015\012
\015\012Each time you adjust hose stand vac up on the table & pull handle back as if cleaning carpet you must not push head of vac down on the table.
\015\012
\015\012Now look at sole plate usually when they are wrong the sole plate bottom back end tilts up lifting brush from carpet.
\015\012
\015\012Now tap front of head down if sole plate springs back up lifting brush up again adjust hose a bit more.
\015\012
\015\012What you are trying to do is get sole plate as horizontal as you can.
\015\012
\015\012If you really cant get it to pick up dirt any better try fitting new hose they are more sprigier from new,
\015\012
\015\012http://dysonmanuals.llc.nu/
Repair Help & Product Troubleshooting for Dyson DC07 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I need more suction. The Head is too high on my carpet.


Hi.\015\012\015\012A slitght adjustment can be made by either screwing on short transparant internal hose on top of floor head tighter or undoing it turn.\015\012\015\012Do this on A table as you need to get down to be able t ... Dyson DC07 Bagless Upright Cyclonic Vacuum

With the hose on I have suction, with the carpet head not much


It looks to me u have something stuck in ur hose or in the carpet head....if u can loosen the hose use a broom handle and push it true....u may be suprized what u will find......good luck ... Kirby G5 Bagged Upright Vacuum

My dyson vacuum cleaner doesn't seem to have the same suction power it used to. I have cleaned out the canister and have taken apart the vacuum head (for cleaning carpets) and it doesn't seem to be blocked but it seems to lose suction by the time it reaches the head. The suction is strong at the end of the hose (where you attach the telescopic attachment with vacuum head) Any ideas? Thanks, Irene


... Vacuums

Solaris electro plus need replacement roller brush for electric carpet cleaning head


The part number for the roller is 4929740 if you are in Australia or NZ we can get the part for you (VacuumSpot) ... Miele S514 Solaris Electro Plus Vacuum

With cleaning carpets with the Stowaway when the head gets a blockage it makes a high pitched whining sound and requires unblocking - then works fine. Now when vacuuming the head always makes the same sound when the head is against the carpet. you can also see that the rollers are slow or stopped. We have pulled the Stowaway virtually completely apart and checked for blockages as well as washed the filter and no difference. Any ideas?


... Dyson "Stowaway" Canister Vacuum Vacuum

On our new carpet (which is not that thick but thicker than the old) I can't set the carpet thickness high enough. The suction really grabs the carpet and bogs down my self-propelled wind-tunnel Hoover. I then have to push down on the handle to tilt the front up. The thickness setting is as high as it will go. Is there some way that I can further adjust this. The machine is about eight years old.


I can help you out only if you will let me know the front width of the machine. Alongwith the height which you wan't to give raise. KIndly give the width and elevation in cms. ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

It,s the suction power. I need to go over and over the carpet to pick up small things on my carpet. I need yor help to solve this problem.


The top of the cyclone unit can clog with fluff, remove the 3 torx screws and carefully lift off the top, it won't come away completely as the flap release trigger rod is connected to the lid.\015\012remove any fluff you can see between the cyc ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.


The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

Carpet/floor suction cover for ge carpet cleaner 106727 need replacement or source for one.


... Vacuums

Carpet head on Kirby upright is stuck up high


Remove the nozzle and remove the front wheel shaft. Take these 2 screws out. When doing so - watch for the spring that is under the top pedal, ... Kirby G4 Bagged Upright Vacuum

While using, steam stopped coming out in force at the port levels in the head. Suddenly started high pitch whining, pressed button just above connection site and end flew off with great force pouring water onto floor and carpet. Unplugged immediately for safety and unable to get it to deliver steam force again. Less than one year old and used only 8-10 times only in walk areas where there is no carpet with distilled water. Please, advise, cannot find booklet. Thanks So Much, Beverly Crumme


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it may not be getting steam to the head...Euro ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

I have an electrolux renaisence vacuum. the brush in the floor attachment turns but I have no suction. When I change to bare floor option on the handle the brush stops turning (correct) but I still have no suction. The lights on the handle showing --floor,carpet, high and low all work.


Sounds like you have a clog, either in the hose or the inlet by the brush roll. ... Vacuums

Bissell lift off vacuum about 4yrs old. Extremely noisy. OK until before Christmas but getting worse every time it's used. Washable filters washed, HEPA filter replaced. brush bar cleaned of every scrap, hose empty,everything that can be cleared has been. Noise high pitched, screeching and can only bear to use it for a few seconds at a time. Suction OK. Mine is so loud I can't use it very long-high pitch screech. Can this be fixed or does the whole vacuum need to be replaced? It still cleans gr


Sounds like a bad motor. Could be either foot motor or main motor either way cost will be more than half of the unit. ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

I have a Eureka Boss Model 411... I need to know where the reset button is for the suction motor. The canister was clogged on the backside, I didn't see it and the suction motor shut off. I have cleared the obstruction, but don't know where the reset is for that motor. I know how to reset the brush head motor.


If your vacuum motor overheats, it will stop working. it will start working again once it cools. ... Eureka 411A Upright Vacuum

I have a Kenmore Elegance Vacuum with Dirt Sensor, Model # 116.30750400C, Serial number M41901532. When vacuuming the carpet the power head will work for 3-6 mins then automatically shut off, power is still there and lights work but the power head motor turns off and the suction stops. I will turn it off and on, check the outlet, flick the on off buttons...nothing. I will turn it off for a couple minutes and it turns back on and runs like normal. I've check the bags, filters, cleaned the hos


It is an electrical problem in the handle, if you can or know somebody that has any fix it ability it can be fixed in about ten minutes. Oh, and Sears SUCKS!! ... Kenmore 34612 Bagged Upright Vacuum

Suction centralux vacuum two years old doesn't have the volume air movement it once had. Unit will still quickly reach an extremely high head of suction so no broken pipes. ran napkins thru no blockage, overode filter safety switch ran with out filter no difference. just don't move air like it used to


Hi!!! clean motor blower blades ,they collect alot of duct and the air in chopped,Good luck.Clean blower fan blades.. ... Electrolux Centralux Vacuum

Help i can get suction from the hose but when i stick it in the back of the carpet head i get no suction and the beater bar will not turn. can you help


... Miele S184 Powerhouse Bagged Upright Vacuum

Tristar vacuum, power head carpet attachment very little suction


... Vacuums

Have cleaned filters but no ever replaced them... suction is rubish always have to use it without the head on... any ideas, is it just new filters are needed?


Well, I have used one of those vacuums before and its suction was sluggish, and it was brand new too. It might be clogged up where the suction is produced, see if that. If not you might just need new filters and also you should call customer support ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum

Powerhead woes Drive belt for power head beater brush on Hoover S3755 keeps jumping off drive motor shaft when vacuuming low pile carpets like oriental rugs unless minimal suction is used. Any tricks to keeping the belt in place other than this?


I've had my Hoover S3755 for about 2 years and loved it, at least until the last couple of months when the "belt slipping off" problem started. I changed the belt and the vacuum would work for a little while then the belt would come off again. I pu ... Hoover S3755 WindTunnel Bagless Canister Vacuum

The brush head will not press down and brush. It just sits high over the carpet


Loosen the motor housing cover and reinstall. the head probably came out of alignment but this should fix it. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Sanitaire commercial vacuum On some carpets, we can't get the correct height adjustment. It's either too low, so the beaters stall and don't spin, or so high that it fails to pick up animal hair. I'm not sure if something is malfunctioning or if I need to have a better understanding of how to adjust


... Electrolux Eureka SC689 Sanitaire Commercial Lightweight Bagless Upright Vacuum 14lbs

My Kenmore model 116 vacuum head will roll in carpet mode but no suction, no action at all in floor mode.


Tripped overload, try resetting...Check pic.... ... Vacuums

I have a Hoover carpet cleaner F5358-900 It no longer sucks up the water. I have taken it apart from the top down and can find no real problem. (Although I am a woman!) The spray works and the scrubbing heads go around. Should I try to disassemble it further--I will need a special screw driver? Thanks, Jana


... Hoover Vacuums

I have a kirby sentria vaccum carpet shampoo system and I cannot get the shampoo suction head to work! It comes on but the belt is not turning. I have tried taking it off and looking at the assembly but no luck. And I have tried turning the belt engage lever to off and on to see if it makes any diference.


I had the same problem at first but figured it out. Make sure before you put it on the vacuum itself, that the shampooing unit is completely together. The belt needs to be taunt like it would be when the brush is turning. Once you put it on and turn ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0680 seconds