Having problems with your Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum ?

DC20 Turbine Head rubber part torn

\015 I admit I was stupid: I was fed-up with how often the turbine head was getting blocked up with small items, due to the presence of a rubber flap with a small **** design to prevent passage of anything larger then an orange pip. This was between the turbine and the brush-bars in the air-flow passage.I tried to widen the opening, and took off too much rubber. now the turbine does not have enough pressure to work correctly.I cant find this part listed anywhere, and dont want to spend the near \302\24350 for a whole new head.Any help on where to find this part would be greatly appreciated. (Yes I know I need Torx screwdrivers and a bit of know-how to get inside the device.)\015

Answers :

The only place you might get the part is from Dyson
Thet do not let these type of parts to any trade
Repair Help & Product Troubleshooting for Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

DC20 Turbine Head rubber part torn


The only place you might get the part is from DysonThet do not let these type of parts to any trade ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

We have a Dyson stowaway DC20 Turbine and the turbine head is not spinning at all.Can you please advise if this can be fixed and how. Thankyou from, Bev Effern 0411 018 531


Are the pins at the connection between the wand and head damaged? Has the turbine been verified that there is not blockage? ... Dyson Vacuums

I have a Dyson dc20 the turbine head is not working what can be done?


... Vacuums

Dc11 dyson the brush head turns very slowly but when i take brush head cover of (the yellow part) and put my hand over the suction inlet part the brush head turns really fast. Have cleaned out collection chambers eg the hoover bag have washed the sponge with the little pictures of taps on it what now . thanks alan


I have taken the brush heads off and pulled all the hair out of the small gap between the chrome shaft and the plastic gear housing. Then a small amount of 3-in-1 oil into that gap to lube the internals and just a little through the air intake on th ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum

The turbine head does not have suction


... Dyson DC22 Motorhead Canister Vacuum Bagless Cyclonic Vacuum

Suction on my dc08 is very poor when turbine head is attached - no problem when not. I have cleaned the brushes an ensured there are no blockages. Why the loss of suction when using turbine head ?


Please go to the web page www.dyson.com and go next http://www.dyson.com/support/help.asp?article=1468&product=DC22-TURBINEHEAD-USand fix it. with commong sense.God bless you ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

I am trying to find out a part number for a rubber gasket that goes on the inside of a Hoover Windtunnel Cyclonic Platinum BAgless upright. It is a very thin, light-weight gasket made of rubber that helps seal the filtering tubes. If you know where I can find a parts break down, please advise,,, JON [email protected]


Hi There,\015\012\015\012I'm not sure exactly which part you are asking about, so I went ahead and uploaded the parts schematic of your vacuum cleaner, that will diagram all the parts, and part numbers.\015\012\015\012If you n ... Hoover UH70015 Bagless Upright Cyclonic Vacuum

Falling apart http://pdf.oreck.co.uk/user/qvc/OK2483%20Power%20Team%20U38052HHPDQ.pdf part 10 coming away from part 12 whilst vacuuming and parts 11 letting out dust, even when attached. Rubber seals in place and tightened as instructions.


... Oreck Vacuums

Need part for stand of Hamilton Beach Scovill Model 44 Mixer. Part is locking rocker tab that hold mixer in place on stand or press to remove mixer head from stand. Don't need spring or pivot pin, just rocker tab. Don't have part number.


... Vacuums

Part replacement we have one of your "Shark steam cleaners", that while moving from one room to another, was dropped. The head separated from the part that holds the water and broke in the process. Can this part be purchased.


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Turbine head Dyson DC39 The turbine does no stay on consistently


... Dyson DC39 Animal canister vacuum cleaner

Is it possible to disassemble a Dyson floor tool/head please? (Not the turbine head!-the duel floor head!)


Take the head off then take to the nearest garage and use there vac to **** it out or the blow it out with there compressor. ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

DC07 and mini turbine head don't get along.


You can buy a clip from espares on ebay ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Turbine head of my Dyson DC08 does not spin


This response is likely too late coming, however for others the problen appears to be the same as the fault with my turbine head which was that the turbine fan had become loose on its spindle. With no pressure on the brushes, friction would allow the ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

The hose on my Samsung 9048R is torn partly from the swivel base. The main problem is that the carpet attachment with the beater bar will not operate now. My brother checked the connectivity at both ends of the hose and there is juice at the bottom swivel part but at the other end of the hose where the carpet wand plugs in it is dead. is there any way to fix this? How does the wire go up through the hose? I have looked around on the internet and it would seem that the entire hose assembly is


... Samsung Quiet Storm 9048R Bagged Canister Vacuum

The brush on my Kenmore Pet Power Mate no longer spins. I opened it up and found the problem may be with the rubber band connecting the spinning parts. Where might I purchase a new rubber band for it?


Try this link > http://www.vacuums24x7.com/kenmoreparts.html ... Vacuums

Power head attachment works great when plugged into the hose part of the vacuum. The problem is when I attach it to the tube for normal use there is no power. I have checked all the connections and switched the power switch on and off still no power from tube to power head. Is there anything else I can try? Model Callisto


Try having someone turn the machine on and off while you pull the cord in and out with the cord more angled towards the on/off switch. Sometimes these models have a break in the cord rewind and will not put the power through to the motor. ... Miele Vacuums

We are putting our Hoover steam vac F7425-900 back together again after getting a new turbine assmbly part. However, we have a part ( #38454-013) that we are unsure where it fits. Can you assist us?


... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

My Triton T80 SI shower is leaking from where the outlet pipe assy joins to the heater can assembly. when I checked where the two join together I see that there is a rubber O ring fitting into a recess in the heater can assy. The screws which hold the two parts together does not force a compression between the two parts causing it to leak. Is there another modified unit or am I stuck with what Ive got and should I replace the O ring or the shower.


... Vacuums

Bissell 2x has suction coming out of the "base" part(when I put my had over the rubber ring that leads from base to the handle part there's suction), but there's no suction coming out of the hose. I'm not certain if there's a clog, 'cause I can't get the hose off.


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Generation 3 Kirby Vacuum is giving off a burnt rubber smell when I vacuum. I have tried to raise the height of the head but it still happens. Can you tell me what could be causing rubber to burn? What needs to be fixed?


The belt driving the brush roller in the power head is slipping. It is really just a big thick rubber band. Where it wears out it slips and burns due to friction. Look at the bottom of the power head. There is a cover plate held with 2 to ... Kirby Generation 3 Bagged Upright Vacuum

I am trying to disassemble a electrolux 2100. I have looked at instructions given by Chemist 1961 and others. On the side, I have removed the rubber covers over the plastic rails but I can't remove the plastic rails that hold the rubber covers on. If I am right, these rails should just slide right out and the outer casing should come part.....or am I doing something wrong. I have pulled and pulled the rails and they don't budge. The rear end won't pop off. Help!


There's a tab at the back of the rail that needs to be released. Turn the vacuum on it's side, slip the tip of a standard screwdrive into the space between the rail and the back of the vacuum, and tap lightly with a hammer. Tap toward the front of ... Electrolux Lux 5500 Canister Vacuum

I checked the belt and it has not broken, but when I start to vaccum the spinning head stops, and I start to smell a rubber smell...Do you think I need to replace the belt, I did get some string caught in it the last time I vaccummed, and it did stink like rubber then also...


Yes you do need to replace the belt they stretch out. Think of a belt like a big rubber band if you were to stretch it out and hold a lighter to it the rubber band would stay stretched out. That is the same thing that happen ... Bissell Vacuums

I Have two questions concerning my AIRVAC AV2500 Red Series Vacuum System. How do you replace the light in the floor power head sweeper and can you replace the permanent fabric filter? We had the system installed in 2004 and the light in the sweeper head just went out and can not find any manual on line on how to replace it. The filter if not torn but avter 6 years it probably needs some kine of cleaning or replaced even though it says permanent. Any help would be appreciated. Jim McCluskey


... Vacuums

Spare part for oxy3 system cleaner. The joining part at the vacum head is broken and needs replacement


I sought out the spare part I needed and fixed the problem. ... Electrolux Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0472 seconds