Having problems with your Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum ?

How to pull apart the cyclone barrel on my Dyson DC11

\015 I have had my DC11 for a few years now and after looking inside the barrel noticed how the dust seemed caked like cement up inside the barrels. I hosed it out and managed to get most of it clean but decided that I should pull it apart further and make sure it was clean and dry before use. I pulled out all the little black screws but it still dosnt want to pull apart and I dont want to force it. I cant find a service manual anywhere online. Does anybody know if there is a secret to pulling it apart?Cheers\015

Answers :

To Pull Apart the DC11 Cyclone section there are three more screws
but to get to them you need to remove the button (the one that unlocks the flap to empty the dust out) There is a small rectangular hole on the other side of the button, pushing a small screwdriver (3-4 mm jewellers ) will release the button this will reveal one of the three remaining screws , removal of the plastic section retained by this screw will reveal the remaining two
I love the Dyson (DC07), but after 7 or 8 years it lost suction and needed some attention beyond filter cleaning. After much online research I found the few bits of advice that for me were the holy grail. After all of the standard stuff, clear clogs, clean filters etc..... In this order: 1) Remove & empty the canister, ***important****-leave the canister bottom lid open. 2) remove the three star screws at the top of the canister. It'll take a bit of pressure to pull the top up, there's a rubber seal. When you pull it up there will be a rod running down into the canister, leave it be, just pull up the top high enough to clear out any debris. 3) Put the top back on aligning the screws, when you lower it make sure the bottom of the rod engages with the hole at the bottom center of the canister, this is why you left the bottom lid open. Put the three star screws back in. 4) Turn the canister upside down, lid open, and keeping in mind this is thin plastic, gently tug upwards on the four fins that surround the bottom rubber seal. This part is held in by friction, so work your way around the four fins gently pulling until you work the ring they're connected to free. This will give you access to the inside of the canister. 5) remove the round perforated section by tugging upwards on it, set it aside with the fin part. 6) Take the canister to a laundry tub or large sink and holding it bottom up fill it with hot/warm water. Grasping the center section shake it vigorously and turn it upside down while shaking and a bunch of sh*t will come out. Repeat several times. 7) Dry thoroughly, you might use a hairdryer held to the center tube, but only if you can switch off the heat and use air only. Make sure its 200% dry, water will kill your machine 8) clean and replace the round perforated section 9) replace the fin section, I'd suggest pulling the round rubber part off of the fin part and setting it in place on the canister first, then follow with the plastic fin part. If you don't do it this way the rubber won't seat properly and the bottom lid won't close. 10) Close the lid, replace the canister, and staaaaaart suckin like it's brand new.
Repair Help & Product Troubleshooting for Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to pull apart the cyclone barrel on my Dyson DC11


To Pull Apart the DC11 Cyclone section there are three more screwsbut to get to them you need to remove the button (the one that unlocks the flap to empty the dust out) There is a small rectangular hole on the other side of the button, pushing ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum

How do i pull my DC08 Dyson barrel Vacuum apart


... Dyson Vacuums

I need a diagram that shows how to pull apart the Dyson Rot8 cyclone 124-US


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dyson dc11 cord rewind - Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum


... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum

Dyson spring release came apart - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum


Thishappened to me too. I had to order a spring kit. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Dyson pet has lost suction what can i do? - Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum


Hi there,If your Dyson Animal doesn't seem to be picking up as well as usual, I'd encourage you to visit www.dyson.com and click 'Support'. You'll be able to identify your machine from the lis ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum

How do i take the dyson dc 41 ball apart - Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum


... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Dyson vacuum suction loss - Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum


Clean it outcheck all the filtersI think it has a foam filter as well as the filterless designclean and lubricate the motormake sure it is not leaking and sucking in air from somewhere else ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum

Dc11 suction loss - Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum


... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum

Dyson mini turbine head - Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum


Hi there,I can't tell from the information provided what sort of issue you're having with your mini turbine head, but you may find our support guide of use in resolving any difficulties: ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum

How to pull apart dyson 29 turbine head


Hi Garry,Thank you for your question. We would like to provide further assistance but it would be difficult to provide all of the information in this space. We would appreciate the opportunity to discuss this over the phone in greater detail. ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

HOW DO I REASSEMBLE CYCLONE ASSEMBLY DYSON DC11


Dear John,Thank you for your inquiry. We do not recommend disassembling your cyclone assembly, as a result there is not a diagram available. However, we would like to provide further assistance. Please call us directly at 1-866-693-9766 (US) ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum

The holes on my dyson dc07i are dirty and smell how can i get them clean does the part with root cyclone on it come apart


Hi Susan,\015\012\015\012We'd strongly advise against attempting to disassemble the cyclone pack, as this is likely to snap the internal bin-base release rod, and can also reduce the performance of your machine. \015\012\015\012If you ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I accidentally sucked up water with my purple dyson slim. I pulled it all apart and waiting for it to dry. Now what?


... Vacuums

How to take apart to clean - Dyson DC07 Bagless Upright Cyclonic Vacuum


This video will show you ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Item stuck on brushbar how do I take apart - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum


This video will show you ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Cleaning! To clean the cyclonic cone Dyson say to use can-air? that may be ok for computers but not to blow out the dirt and dust from the cone in question. Someone else here suggested to use a real compressor! Well dahhh I knew that! Should I do the blowing in the living room? or may be in the bathroom? Seriously what I need is an assy. drawing to take it apart and washing it Any ideas where I can get one? Thank you John


Hi, we realy love our Dyson, but get frustrated when it gets clogged with pet fur (2 cats and 2 dogs). This takes a little effort but what we ended up doing was taking the vacuum apart into its major components and alternately blowing it out, filter ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Turbine headbrush wont rotate - Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum


Make sure it's pluged in to exstention pole secure and switched on ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum

Putting the hose to vacum - Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum


This link is for the manualhttp://media.dyson.com/downloads/generic/Manuals/dc11_gen_manual.pdf ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum

Trying to take it apart to clean - Dyson DCO3 Absolute Bagless Upright Cyclonic Vacuum


... Dyson DCO3 Absolute Bagless Upright Cyclonic Vacuum

My Dyson will not turn on unless I pull the handle back. I have take the entire vacum apart cleaned all blockage and it still will not turn on in the upright position.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Dyson Animal upright (purple). I took it apart to clean the cyclone chambers. When re-assembling the bottom closed before the opening rod was inserted. I can't get the opening rod installed with the bottom opening closed. How do I open it? Thanks.


I looked in our DC07. I would try removing the top again and getting a long dowel or the opening rod, insert it down into the unit and PUSH. The opening rod opens the latch by pushing it, not pulling it. Here are some pictures of the latch. Top pi ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

How do I take apart to clean machine - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My bristles wont spin - Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum


Hi Maggie, Alec from VacuumSpot here. There are 3 reasons why the brushes might stop. The first and easiest is to check if the turbo head is set to carpet - there is a ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum

Barrel Dyson DC08 Origin cord rewind button is stuck.


... Dyson Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0679 seconds