Having problems with your Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum ?
DC 11 issue
\015 The suction cup will not stay in on the multi floor tool for soem strange reason, would appreciate any advice. It keeps popping back out when pressed in.\015
This may be due to diminished suction. have you tried cleaning out the filters? Try rinsing the filters throughly with water and then letting it COMPLETELY dry out before reinserting. Also try cleaning around all the rubber gaskets on the dirt bin.
Repair Help & Product Troubleshooting for Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Power Issue Hi...my Miele vacuum cleaner (S314) will not turn on, unless I lean it on its side (the side that the power switch is on). I took it apart and the wires are all well attached, and I do not see any issues with the connectors. Is this a common problem with an easy fix? Thanks! Todd
Could be the cord reel causing the problem. Sometimes the contacks on the inside of the reel loose contact and won't conduct. If this is the problem, then you will have to replace the reel cord asm. Part # 06777540, may cost about $150 approx. ... Vacuums
I have a iRobot 4150 and have recently experiencing performance issues with the vacuum. Recently, it started stopping about a minute after you turn it on. I thought maybe the battery was the issue, but I bought a replacement. It has worked well for the past 6 months. While it's running it sounds like it is going to die, even though it is fully charged. Any ideas?
Yes, a common issue with the cleaning head module, chm. You will need to diassemble the Roomba and remove all debris from the CHM. Also take a look in its gear box. ... iRobot 4150 Roomba Vacuum
The unit works well for 3~4 minutes and then stops. Wait another 10 minutes to cool down and it works again but the same issue happens again and again. It is a brand new unit. I read the manual for the thermal detector and did what it says but the issue is not resolved. Thoughts?
Hi, I have a Hoover Bagless myself. I also have worked professionally fixing Vacuum Cleaners. There may be some material caught between the roller end and the end bearing or the edge of the roller compartment. This could b ... Hoover UH70015 Bagless Upright Cyclonic Vacuum
Dyson dc11 cord rewind - Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum
... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum
Err5 When charging the battery, it starts out flashing amber, but after several minutes it turns red and the err button flashes five times. The troubleshooting says to hold the buttons above and below the power button for ten seconds and this may resolve some software issues. I tried that but it goes back to the amber light then red again. I replaced the battery hoping that was the issue, but it still does the same thing.
... iRobot Roomba 530 Robotic Vacuum
I have a Kenmore DuraPower Dual Cyclone Action 12 Amp that just randomly stopped right in the middle of vacuuming. I assumed the plug had come out of the wall so I went to check and this wasn't the issue. I tried multiple outlets and that wasn't the issue. I made sure nothing was stuck and there is nothing stuck. Nothing happens when I press the red "ON" button. What could this be? Thanks!
... Kenmore Vacuums
Hoover carpet cleaner F7458-900 issue The detergent is not dispensing? Tried cleaning the valve cap (per Hoover manual) yet the issue persits. Any advise?
The pointed valve that is in the tank may need replacing. The two valves are a set. I just ordered some from www.usavacuum.com ... Hoover F7458-900 Upright Vacuum
Low suction I have a Hoover central vacuum system. I've reset the fuse box, checked the fuses, all of the lines are clear and there are no holes for escaped air to travel out. The filter has been cleaned as well. The vac works well with high suction when hooked directly to the unit, however when using any of the indoor connections there is extremely low suction. The machine still turns on so I do not believe it is an electronic issue. I have troubleshooted the issue as best I could and would
... Hoover L2310 GUV Central System Vacuum
Dc11 suction loss - Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum
... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum
Kenmore canister switch issue
I have the same problem and took it apart. There are two switches: one on the hose and one that activates the motor - on the right side just inside next to the motor. Took the switch apart (V-`0G-3C25-L) and found it was fried - slightly melted. ... Kenmore 25512/ 25513 Progressive Canister Vacuum
My Power head on my Dyson Animal DC39 will not stay spinning. Suction Issue?
There should be a red insert on the right-hand side on the cylindrical bulge behind the brush cylinder. Check that this is moving when you push the button. The red insert should stay pushed in for the brush to rotate. The insert moves in an out as we ... Dyson DC39 Animal Canister Vacuum
Dyson dc11 replacing motor
DYSON DC-11 MOTOR REPLACEMENT1. Remove dirt cylinders as normal2. Using large flat screwdriver, remove airway splitter and hose3. Undo 6 Torx screws from top and one at the back under tool holder ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum
How to pull apart the cyclone barrel on my Dyson DC11
To Pull Apart the DC11 Cyclone section there are three more screwsbut to get to them you need to remove the button (the one that unlocks the flap to empty the dust out) There is a small rectangular hole on the other side of the button, pushing ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum
How do you take the DC11 apart?
Unplug the unit from any power first.\015\012\015\012\015\012To get the unit apart you have to Carefully pry off the wheels from both sides of the unit to allow access to another 4 torx screws. Use a longer flat blade screw driver ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum
Hoover S3590 Bagged Canister Vacuum power issue
The problem you are describing sounds like to be electrical in the cord reel. I would take it to a repair shop for estimate, sometimes these can be repaired rather than replaced. If under warranty, I would definitely take it in. ... Hoover S3590 Bagged Canister Vacuum
I have some charging issues with my 530 roomba
Yep, new battery time. ... iRobot Roomba 530 Robotic Vacuum
Dyson dc30 charging issue
Dc11 dyson the brush head turns very slowly but when i take brush head cover of (the yellow part) and put my hand over the suction inlet part the brush head turns really fast. Have cleaned out collection chambers eg the hoover bag have washed the sponge with the little pictures of taps on it what now . thanks alan
I have taken the brush heads off and pulled all the hair out of the small gap between the chrome shaft and the plastic gear housing. Then a small amount of 3-in-1 oil into that gap to lube the internals and just a little through the air intake on th ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum
Vaccuum issue I just bought a Eureka upright model 5892 BVZ, my concern is, I bought it on sale (floor model) and it didn't have a manual with it. I took it home and tried it, and although it appears to be working very well there is not dirt in the catch bin on the front of the unit. I tried the hose w/attachment and again it worked very well in picking up the cat hair, but where does the hair and the dirt go, I am afraid it is spitting it back out somewhere since I can not see anything in the c
If the dirt being vacuumed is not going into the dirt cup, then it must be just stuck in the hose and evenually will clog up. Check the hose and see it there is a clog in it, otherwise you have a years warranty on a new vacuum, take it into a warran ... Eureka 5892AVZ Bagless Upright Cyclonic Vacuum
1993 chevy silverado 1500 fails emission and has error code of 32 this refers to EGR issue but i need a vacuum diagram to figure out if any hoses are missing has anyone had any dealing with egr fail code?
Clutch Issue How to replace the clutch in the Dyson DC07
Greetings from GoVacuum,\015\012\015\012The clutch repair is not a simple task, but if you watch the video below closely, you can certainly get through it. You'll need to purchase a clutch system (it's best to stay with the genuine Dys ... Dyson DC07 Bagless Upright Cyclonic Vacuum
DC 11 issue
This may be due to diminished suction. have you tried cleaning out the filters? Try rinsing the filters throughly with water and then letting it COMPLETELY dry out before reinserting. Also try cleaning around all the rubber gaskets on the dirt bin. ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum
Hoover Wind Tunnel bagless- issue with turning on
Have you tried to plug the vaccuum in another outlet that is on another breaker? It could be the vaccuum tripped the breaker. Turn the breaker back on. The manual mentions the thermal protector could have been activated. If this happened it reset ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
Bissell PRO Heat Steam Cleaner is not dispensing the water. I took it apart and cannot find any obvious issue with it i.e loose tubes, connectors etc.
Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn't squirt, check for the seal at the bottom of the tank, it needs to be o ... Vacuums
KIRBY ISSUES! :(
Sounds about right you should change that type of belt every six months to a year regardless if its broken or not. one other thing you should do is make sure the brush roll itself isn't bound up it should spin freely if not you can pull the plastic e ... Kirby Ultimate G Bagged Upright Vacuum