Having problems with your Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum ?

Dyson dc11 replacing motor

\015 How do you replace dismantle a dyson dc11 and replace the motor?\015

Answers :

DYSON DC-11 MOTOR REPLACEMENT


1. Remove dirt cylinders as normal
2. Using large flat screwdriver, remove airway splitter and hose

3. Undo 6 Torx screws from top and one at the back under tool holder

(Note that 2 front screws are shorter)
4. Make sure the screws are completely withdrawn

5. From the back, withdraw tool holder section

6. Unhook and withdraw hose holder section

7. Place large flat screwdriver behind the wheels and forcefully snap them off

8. Remove 2 more screws under each wheel

9. Cover now lifts off

10. Motor pod is now visible. Remove its 4 screws and lift its lid

11. Motor can now be lifted out. Disconnect its 2 wires

12. Remove the rubber base and transfer to the new motor

13. Connect wires, Red to Brown (Live) and Black to Blue (Neutral)

14. Make sure motor is correctly fits on its alignment studs in the pod and replace its cover and 4 screws

15. Replace top cover of machine, and the 4 screws under the wheels, but no other screws yet

16. Turn machine on its side and hammer each wheel back on - take care that no fingers are under wheels while doing this

17. Stretch and snap hose holder back into position

18. Slide tool holder forward into position

19. Replace the 6 screws into top section, and one into tool holder section

20. Replace filters, airway splitter and dirt cylinders, and the job is complete :D
Repair Help & Product Troubleshooting for Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dyson dc11 replacing motor


DYSON DC-11 MOTOR REPLACEMENT1. Remove dirt cylinders as normal2. Using large flat screwdriver, remove airway splitter and hose3. Undo 6 Torx screws from top and one at the back under tool holder ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?


Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

DYson DC07 not sucking properly when in upright mode. I have tried cleaning out pipes etc and even tried an old motor section I had in garage (replaced once under warranty as kept cutting out and they left old motor section here). Even the old motor section had same prob so this suggests its something in the rest of the vacuum cleaner (whats left after you have lifted off the green motor section and dust collection area if you see what I mean? Any advice weclome please.


Blocked filters ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Wiring diagram for Dyson DC05 Motor. Bought a replacement motor and wiring slightly different from original. Thermal cutout on both motors.


... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

I have just replaced my Dyson DC14 Motor and now it blows the hepa filter out and filter cap off from under the bin the air is really hot. Is something wrong?


This video on the link below may help youhttp://www.youtube.com/watch?v=6HQx-gFA3MI ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Unable to find a panasonic replacement motor for dyson dc07 vac.


You can convert it to the YDK one if you get the YDK motor housing as well. ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Dyson dc14 Animal motor brush replacement


By the time the brushes are shot, so is the armature. You need a motor. ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Take motor out of dyson o7 how do i take out old motor and replace it


This model takes specialized tools to take apart. Even the belt replacement takes a factory tool. It is crazy I know. You will have to send it off to a warranty dealer. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Dead motor I purchased a new motor for my Dyson Animal but I cannot figure out how to get the thing apart to replace it. There are weird star shaped screws but I can't even see how removing those would get me where i need to be. HELP!!!


Ace Hardware or Home Depot should have your star screws ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

How to replace brush bar motor on dyson dc15 - Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum


... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Dyson vacuum How to change the motor for a new one? How to seperate the plastic housing? Where to purchase a replacement motor? Thankyou


Hi There, I have posted up a youtube video showing how to do this repair on a dc08. The dc29 is pretty **** close in design in terms of the motor cavity. In terms of where to buy a motor amazon if you are in the US, ... Dyson DC29 Animal Vacuum

How do you replace motor on DC29 Dyson vacuum


... Vacuums

I have a Dyson DC 15.need to replace the motor cover assy. can't get the part under to pop off . what holds this down.


Check the manual for the troubleshooter: Dyson Dc15 Manual ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

How to remove motor on dc11 dyson


... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum

Dyson dc24 replacement motor


Try this linkhttp://www.sparesaver.com/vacuum-spares/dyson-spares-parts-accessories/dy ... Vacuums

Motor replacement dyson dc21


... Dyson DC21 Bagless Canister Cyclonic Vacuum

Dyson dc04 wont pick up,motor working,replaced clutch assembly but still dosnt turn brushes


You need to go through a process of elimination. You are better doing that here: Dyson advice forums ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a dyson root cyclone. i dismantled it to replace the belt, it is not the belt which is on the roller brush, it is the belt which is from the motor, it was easy to take out as it was broken, i will get new one tomorrow now im wondering how do i fit it in.


The belt that fits on the motor is the same belt that drives the roller brush, all you need do to gain access is remove the sole plate, normally attached with 3 quarter turn connectors, use large flat screwdriver to turn them ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a Dyson DC04 which is making a strong burning smell within a few seconds of switching on. Is this likely to be the motor and if so can it be replaced?


More likely it is the beater brush which is jammed and not turning. Turn the machine over and remove the bottom plate. Unhook the drive belt, then try to turn the beater brush--it is likely bound up with string, thread, and hair. Try turning the mach ... Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum

HOW DO I REPLACE THE MOTOR IN A DYSON DC14 PLEASE


There is a full guide here: Dyson motor change. That guide is for a DC07 but the machines are almost identical to swap ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Dyson DC07 My DC07 cuts out after 5 mins and I want to replace the thermal cutout. I have cleaned it thoroughly, including the cyclones but it still cuts out. How does the plastic moulding around the motor dismantle? I have started by removing the 4 torx screws but the upper grey housing does not want to detach and I am worried about breaking the plastic. Appreciate any advice.


Try this page: -http://www.fixya.com/support/t192124-overheating_dyson_dc07Regards Gualo ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a dyson dc14 how do i repair my vacum? i need to try to replace the brush bar motor or something so that i can get the brush bar to work again.i hope you can help me out


Brushbar not spinning:--\015\012Ensure brush control is set on carpets mode. Note: brushbar will only spin when\015\012the handle is reclined.\015\012To get user manual for your vacuum please click on the link mentioned below\015\012 ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Thermal fuse keeps cutting in, Is there any way to check motor before replacing it. on a dyson upright cyclone model


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dyson DC11 Carbon Brushes replaced a day ago and now worn away again. Machine will not power on. Any idea what is wearing these away?


The commontator is worn or the mika seperating the sections is too high. ... Dyson DC11 Allergy Bagless Canister Cyclonic Vacuum

Dyson dc11 all floors turbo head replacement ?


Hi there SmartAlec from NelsonVacuums.com.au here. If you are in Australia you can get one from our website. Regards Alec ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0513 seconds