Having problems with your Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum ?

I think the on/off switch has failed

\015 How do I replace the switch--I cannot seem to be able to locate an exploded schematic for this model.\015

Answers :

Repair Help & Product Troubleshooting for Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I think the on/off switch has failed


... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum

Electrolux Epic 6500 SR ...no power to power nozzle. I think it is the switch in the handle because if I use my friend's hose/handle (same model), my power nozzle works fine when I turn on the switch. If you think it is the switch, can I get a part for it?


That's about the best one to narrow down a problem, however, there could also be a break in your hose wiring. Switches, hoses, and hose handle assemblies are all available at your local Aerus Electrolux store. Simply take your entire machine in so ... Vacuums

We have a dyson dc 07 animal the machine was working fine then switched off after returning to the machine minutes later it wouldnt switch on, i removed on off switch cover and used a short piece of wire across the brown wires flicked the wall switch and it worked, aha i thought faulty switch aquired a new one to no avail and now even the short piece of wire trick doesnt work, has the motor died do you think, it wasnt over heating or making strange noises prior to refusing to work


It could be the motor. I'm having to replace the brushes on my DC 05. It appears that you can only get brushes for the YDK motors in the DYSON, not the Panasonic motor. Which might be saying something about the YDK motors. What happens is that the ca ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Central vac our central vac will not work unless the main vac in the garage is switched on manualy.... its sucking fine but i have to switch it off at the main switch in the garage after i have used it normaly i just plug in the hose and vac away and it switches itself off we have just had cable installed with a fisher guy in the walls do you think that would be the problem thanks a lot


It is possible that the low voltage wiring that controls your central vacuum has been damaged during the cable work. You can check to see if the low voltage relay is working by shorting the two terminals together at the unit. Just disconnect the two ... M&S Systems AirVac AVP1200 Platinum Series Central Vac - 12,000 sq ft Bagged Central System Vacuum

Power switch fails to stay in ON position when pushed. I can get a replacement switch but can't figure how to remove the old switch


... Dyson DC07 Bagless Upright Cyclonic Vacuum

I had the vacuum cleaner question about the canister and the wand/powerhead... the Kenmore Progressive Vacuum canister model 116.25812 and the canister not powering off without unplugging the vacuum. The solution I received that they both run on their own switch so it is normal makes sense. However, is there a power switch on the canister anywhere? The only way for the canister to be turned off is by unplugging it. Any ideas? One would think there would be a switch. I am new to fixya and hope


Hi. On some models, one switch controls all of the power. Your issue, which is no working switch is almost certainly a blown triac on the circuit boar ... Vacuums

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?


... Vacuums

I have a Holmes HOH-2400 oil filled heater. one switch of the double lighted switch has failed now only allowing me to use the 700 watt setting only. Whre can I find a replacement switch to fit. It will be an easy replacement


... Vacuums

Brushes stopped The brushes stopped turning while using the cleaner. I removed the brushes to see if the spindle was broken, it wasn't. I then removed the top plastic cover and checked the switch that engages the brushes; it didn't seem to be moving correctly. There's one spring on the switch - should there be two? Or do you think something has broken on the inside? Thanks for any help


Most likely the turbine is bad, it may just be clogged up, you can take it apart and clean it out real good. That may work, but it may not. Sometimes it is best to replace the turbine. ... Hoover F7431-900 SteamVac Vacuum

Hoover model C3820 commerical steamvac when you squeeze the switch on the handle the soap/water will not come out< I think the switch is bad?


... Hoover Vacuums

I have a Electrolux canister model L-E (circa 1986). Won't turn on. I think the foot switch is broken inside. Was working fine - turned it off then would not turn on BUT foot switch sounded different, kinda hollow sound. Perhaps I'm reaching but wortha a shot? Mary


I have one of these LE models also. Yes, the on/off button is broken. I have had to replace it twice on mine. My local vacuum repair shop suggested NOT to use your foot to operate this switch, but just press it on or off with your fingers. That will ... Electrolux UltraLux 2000 Bagged Canister Vacuum

When you turn on the machine the light goes green,I then switch the lever over on the top to red for a hot drink,the machine makes the noise and you think its going to make your drink but no water comes out,My son brought it for xmas last year and didn't think to keep the reciept. thanks lisa


Turn off ... Vacuums

I have a self propelled Royal Dirt Devil vacuum model number 087900 and it goes backward fine but forward has to be pushed so hard it's impossible. Is this a switch? Do you know about how much the part would cost and can it be done by a beginner. We fix a lot of things ourselves but we aren't mechanics by no means. We put a brand new belt on it. I don't think it can be put on backwards and brush turns fine. Where is the switch? Use layman's terms.


You might try a new belt and/or brush roll. The brush roll is what helps pull a vacuum forward, the power drive helps, but if the brush isn't turning like it should, then it will hinder forward motion. The belt may look ok, but they stretch to the ... Vacuums

Brush not spinning , no belt is needing to be replaced, i think something in switch, cause before this problem the switch was always on , i would plug/unplug to turn it on. thisis case with 2 vacuums i have


... Hoover Windtunnel Supreme U5280-900 Upright Vacuum

When I switch off my Vax G3 cylinder cleaner it trips out the whole of the ring main circuit - I think the on/off switch is defective and wonder how much it would cost to repair and who - it is just over a year old


Hello Lyra_cross, if your machine is in warranty please call the Vax Careline on 0844 4128 455, with your machine and receipt available, and an Advisor will be able to help you arrange a repair/replacement free of charge; if you do not have pro ... VAX Appliances Vacuums

Haier 65 pt Dehumidifier. I purchased a new Haier Dehumidifier 2 years ago. I believe this is the third season and it had been working great. Very quite and on humid day's, I have to empty it every 10-12 hrs. Two day's ago it just stopped working, no indicator lights. I plugged it into another outlet to be sure with the same result. I believe it is either the bucket switch or main switch. What do you think and where can I get parts. I live in MA.


HI, this unit has a 12 amp 125v glass tube fuse on the control board. Chances are you blew this fuse. This can happen if the unit is starved for air and ices up. you must take the front of this unit off to access the fuse of this control board. ... Vacuums

Wiring the switch for a kenmore vacuum cleaner I need to know where teh different colored wires go. It had a short in it so I replaced the plug but think I wired it incorrectly. Its a Whispertone 300 model 116.28612790 The canister works but the beater bar doesn't.( it worked before a rewired the switch. Thanks


... Kenmore 23313 Whispertone Bagged Canister Vacuum

I think the switch on the Rainbow E-series electric hose went bad. Is there an easy vway to verify it's the switch?


Hi, the only way, is to test that it has power at the swirch with a circuit tester or voltage meeter, or test the plug on the handle where you attach your power head power cord, or Rainbowmate power cord to.\015\012If it does not get power ther ... Rainbow E series Canister Wet/Dry Vacuum

No power There is no power to my kirby G5. I have checked both safety switches and they seem to be operating properly. I think its the switch but I'm not sure.


Where would the reset button be? ... Kirby G5 Bagged Upright Vacuum

Motor/Fan does not run. I have removed and taken the top of the canister plastic motor housing apart and tested for power. I have power through the cord to the switch and power from the switch to the two wire terminals. I have not removed the motor. Looks like I will need special tools to take out the motor. The Vac looks almost new. It has been setting for several years. What do you think?


Sorry to read about your problem, I hope this helps you out.Well you can order a new motor at shop vac, check out this link.you dont have to remove to check the motor, just connect power to the motor leads ... Shop Vac QPMH450 Canister WetDry Vacuum

4.3 amp Kenmore canister vacuum power switch has failed


You did not give the complete model number, but you can go to sears.com, click on parts and put in you model number. You will get links to click on, click on the cannister one and you get a picture breakdown and a parts list, you can also order afte ... Kenmore 22812 Bagged Canister Vacuum

Wont switch on and changed the fuse thinking that seemed to have lost connection


Henry hoover wont switch on and it is not very old ... Numatic Henry Bagged Canister Vacuum

Oreck Upright Hi Redev, I'm not sure what model I have (about 6 years old...upright, looks like the one in the picture). I changed the belt (which was torn) and then the next time I used it, it cut off on me. Now if won't turn on at all. (I turn the switch on and off and nothing happens as if it is not plugged in but it is!). I noticed at the top where the power cord enters the handle, it is all frayed. Could the electrical wires have detached? Anything you think I should check before taking it


The cord could be bad and will ahve to be replaced. It would have to have a problem inside the handle or down by the motor. ... Oreck XL2600 Vacuum

Carpet brush does not work.but if i lay it on its side it works. i think it a switch but i cant get the handle apart to check it bissell 6405 vacum


You need a new belt. ... Bissell 6594 PowerForce Bagless Upright Vacuum

I have a Hayden SuperVac 3600, almost 10 years old. The unit still runs, but now when I switch to the power nozzle, it doesn't have power to turn that. I think this happened once before and maybe they replaced a circuit board(?). We took it to a local repairman this time and he says he can fix it temporarily with a new cartridge, but that he won't promise it won't happen again soon.....


The hose has fuseable link inside, generally a 3-7 amp. It is at the wall end underneath the hose cuff. Easy to replace as it crimps in line. If you have a meter you can also test the detachable hose to wall cord for continuity, then check the hose t ... Hayden Industries SuperVac 6000 Central System Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0402 seconds