Having problems with your Dyson DC14 All floors Bagless Upright Cyclonic Vacuum ?

DC 14 low reach without good suction

\015 I have a DC 14 Low reach with poor suction. The beater bar is clean, filter is clean and cylinder is clean. Do I need to take it apart to do more? What am I missing?\015

Answers :

Not sure, but there are one or two more possibilities. There are so many Dyson models that It's easy to confuse them, but I think the DC14 has a short length of clear plastic tube leading from the beater bar area to the rest of the vacuum system. Sometimes this tube develops a crack, with the result that air flow around the beater bar is reduced. I suggest you check that.\015\012If you also have reduced suction from the hose, you will need to remove and inspect for blockages in the U tube at the base of the wand fitment, and also in the inspection port which is to the right of that (two yellow buttons to be squeezed to remove it, I think).\015\012If none of this helps, please post more details, if you can, and I'll try again.\015\012Good luck!
Repair Help & Product Troubleshooting for Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

DC 14 low reach without good suction

Not sure, but there are one or two more possibilities. There are so many Dyson models that It's easy to confuse them, but I think the DC14 has a short length of clear plastic tube leading from the beater bar area to the rest of the vacuum system. Som ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Low suction Have a Powr-Flite PF 18, suction is good at motor, but low at where hose comes out of top of vacuum. Could new lid seals help the problem? Where can I get new seals for this model. Also my zip is 98801 and my shop is not listed, could you add it please? Sew Creative 1139 N. Princeton Wenatchee, Wa 98801 509-663-5516 Thanks, Lauren-Sew Creative

Replacing the motor cover solved the problem, it must have been warped and was letting suction out thru it. ... Vacuums

My eureka optima upright bagless vaccum has VERY low suction using the floor part. the hose has excellent suction. i removed the little translucent door underneath and there were no blockages, i cleaned the brushroll thoroughly and that hasnt helped either. i know this probably isnt recommended but i turned it on to the floor setting with the brushroll off and stuck my fingers up the intake as far as i could, the suction was good further up but it just seems to stop down at the base. because i s

I will try and help here. Is the sole plate on the bottom of the vacuum complety on and there are no visible cracks along the seam where it meets the body? This is the usual cause for this. Onc you take of the plate to access the roller and brushes, ... Eureka 431A Optima Bagless Upright Vacuum

My Bissell cleanview is NOT suctioning well, all filters, nozzles, attachements, canisters and belts are clean and in good repair. We've pretty much made sure everything that I can get to without completely dismantling the vacuum is super clean and/or new... still poor suction

Did u check the filter above the dirt cup?\015\012\015\012twist the yellow piece and wash the filter ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

Little green machine pro heat pet the collection tank wasn't collection and dirty water was coming out of the bottom. i took it apart, cleaned it up and put a new "duckbill" gasket in. then it quit spraying, but i think i got that working again. now after i spray and get a good foam on the carpet, i switch to suction and it seems very weak. i can see the water moving (trickling) from the head into the hose but it is not reaching the collection tank -- actually, i am not sure where its goin


We have a series e rainbow cleaner. my wife had been using it i turned off and turned the canister up sie down to get the serial number. it would not turn back on.we need a new hose and thats why i was looking for the serial num. it has a rocker switch and the motor will work on low but will not run on the suction side. i have checked the wiring harnesses out as best i could without taken it all apart. im wondering if it may be the switch. it started once and then stopped.

There is one way to verify if it is the switch.It's kind of dangerous though,but not too bad.You need an extra piece of wire,fairly thick.I would use 4 guage myself.Hold it with pliers,just in case it gets hot.Turn the switch on and hold the wire to ... Rainbow Vacuums

Kenmore upright vac model 33922 - good suction but developed loud whining noise after accidentally vacuuming room without bag. Added bag and changed both filters. Still makes noise. How can I stop noise?

The bag is the first stage in your filtration. Most times what you did will draw fine dust right through the filters and into the motor itself, affecting the bearings and clogging the motor fans, throwing them off balance. The fact that there i ... Kenmore 33922 Direct Drive Bagged Upright Vacuum

I have a Fein Turbo III shop vac for several years now...about a year ago, for no apparent reason it changed into a hideously LOUD beast! It's previously low decibel drone is now so loud it makes my ears ring afterwards...its sound is high pitched, almost like its hose is blocked, but it isn't...and suction remains good...I just can't take the sound...Help me.

It sounds like the bearings in the motor are shot. You can try to get a replacement motor, or if you're a mechanical genius type, you might be able to repair the motor bearings. If the shaft is worn, you'll have to buy a new motor.\015\012Y ... Fein 9-77-25 Turbo III Bagged Canister Vacuum

Does not pick up, no vaccum, motor runs, no blockage, should feel suction on hose outlet without hose hook up. Paper filter missing over cloth filter. float overload ball free, seal on section good no leakage. Maybe bad motor but runs.

Here\015\012 is a Link to one of my Tips:www.fixya.com/support/r6311178-vacuum_brush_bar_not_spinningThis\015\012 should solve the problem. ... Minuteman C82906-01 HEPA Vacuum Vacuum

Low suction I have a Hoover central vacuum system. I've reset the fuse box, checked the fuses, all of the lines are clear and there are no holes for escaped air to travel out. The filter has been cleaned as well. The vac works well with high suction when hooked directly to the unit, however when using any of the indoor connections there is extremely low suction. The machine still turns on so I do not believe it is an electronic issue. I have troubleshooted the issue as best I could and would

... Hoover L2310 GUV Central System Vacuum

Low suction The beater bar still spins fine, but the suction seems low. I have cleaned all of the filters, but it is still too low to spin a lot of the attachments.

Hi Megan,I'm sorry to hear you're having difficulties with your DC17. If it doesn't seem to be picking up as well as usual, you may have a blockage somewhere in the machine. To check for this, please follow the steps shown in our online suppo ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Low suction My old rainbow seized up. I purchased another one on e-bay. It works but it has a broken latch on the side and it has low suction. Even when I press down so it is sealed to the water can it doesn't inprove the suction.

\015\012\015\012\015\012With years of use, you will collect a layer of "micro dust" on the impeller (the fan part) which reduces the efficiency. A toothbrush and some mild cleaner with gently scrubbing will restore it's power. \015\012 ... Rainbow E series Canister Wet/Dry Vacuum

Low suction on Eureka spinduster vacuum cleaner

The belt has stretch enough so as to not drive the brush roll under load. Try a new belt. ... Eureka 2971AV EZ Kleen Bagless Upright Vacuum

Kirby Low Suction

Have you checked the fan? It is what creates the suction. If ok, then you may have a motor problem, sometimes they run but not up to speed, then suction is lowered when that happens. ... Vacuums

Kirby G6 without suction

The power head light flickers when the brushroll is temporarily not spinning. You may need a new belt and/or a new brushroll. As for the unusual sound, you may need to replace the fan. See my troubleshooting guide and from there, you can view my so i ... Kirby G6 Bagged Upright Vacuum

Low suction My 2001 machine is has low suction. The motor sounds fine what could this be?

Is the suction low at the tank after you disconnect the hose? If it is strong there, then the hose may be clogged. You can unhook the hose from the wands to see if you have suction or not. If you do, then look further down all the way to the brush ... Rainbow E series Canister Wet/Dry Vacuum

Low suction I have an Electrolux central vac that is approx. 11 yrs old. the suction is very low. this started about 1 week ago. I checked the hose and it is clear. I also went into the attic and checked the pipes(as far as I could see them) and they appeared to be intact.

1) Have you checked the filter? If it is clogged your suction will be low. Also, you could have a pipe loose where you can't see. Make sure that you can get a coin to go all the way through the hose. make sure the suction motor ( the unit ) is coming ... Electrolux Central Vacuum

Poor Suction Heya! So I just picked up a used Dyson, but when I vacuum with it, the suction is pretty weak and it spits all kinds of stuff out the back and into my feet. When I pull the hose I have good suction, but in regular mode it hardly picks up anything. The brushes are spinning, and it eventually will clean an area if I go over it again and again. Maybe a clog somewhere? Please tell me that Dysons have better suction than my $50 Dirt Devil! Thanks!

I recently bought a second hand Dyson DC07. Its suction was poor. I removed all the un-clipable pipe bits and to remove any blockage but it all looked clear. The Final Sponge and hepper filter did have a lot of dust in it and the rotating brush was f ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Brush spin,good suction at hose, no suction at

Air passage from back of brush head, through the joint, and up to bag, may be blocked. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Suction loss? loss of suction in hose/attachments so not able to get to small hard to reach places. Suction not appearing to work right through hose?

Hi samdan... have you checked all the hose attachment vents .. ie Under the vacuum as well... How long is it since you replaced the filters?\015\012\015\012Try giving the Yellow cone inside a blow out. these tend to become clogged from ti ... Dyson DCO3 Absolute Bagless Upright Cyclonic Vacuum

Poor suction I have a hoover hush s5627 vacuum purchased about 4 years ago from Costco. It's suction power isn't so good anymore. I've checked all the lines & hoses and they're clear and I've changed the bag. I even disconnected the pipe from the vacuum unit and held my hand over the intake. While the machine roars like a jet engine the suction power just ain't like it used to be. What could possibly be the problem?

This vaccuum has a Fan Blade inside connected to the motor that spins to create the suction you feel. After a few years of use (and misuse) the blades on this (plastic) fan will be broken off, thus damaging the unit. These Fans are replaceable if yo ... Vacuums

No suction I have the 3760-4 and have no suction. Does it need an o-ring. Good suction in machine but none outside at hose

The simple solution would be a clog in or leading to the hose. Unless you here a air leak it does not need a new o ring. If there is no clog then you need to take it to your local vac shop for repair. ... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert

Either the hose has a clog, or the inlet down by the belt is clogged. Is there suction at the end of the hose, if not then it is clogged. If there is suction, then it has to be clogged down below by the brush roll, check that inlet. There also is ... Vacuums

Suction I have no suction through the hose. I have taken this machine apart, and checked for clogs, have found nothing, but did give it a good cleaning, still I have no suction.

Hello tnwalkergal the hose may have a clog inside the hose at the bend you can take the hose loose and run a broomstick or a yardstick thorgh the hose this is how I find the clog ... Dirt Devil M086700 Vision Bagless Upright Vacuum

I have any easy-flo built-in vacuum. I recently had the bearings on the motor, top and bottom replaced. I put the vacuum back together and it mow has low suction power. There is plenty of suction on the side of the canister where the rigid tubing meets the canister body but little suction at the wall plates. Any ideas? Roger

There is either a blockage or a pipe is open somewhere. You should check the system at the wall valve without the hose to determine if the pipes are blocked or if perhaps the hose is plugged. If one of the wall valves is damaged or open, this will af ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.8132 seconds