Having problems with your Dyson DC14 All floors Bagless Upright Cyclonic Vacuum ?

The brush on my Dyson DC-14 wont spin

\015 My Dyson was working fine then I heard a weird noise and the brush stopped spinning. Is there anything I can do to fix this ?\015

Answers :

Hello, have you checked to make sure you have nothing wraped around the brushes ? also it sounds like your belt needs to be replaced.
Repair Help & Product Troubleshooting for Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I snagged a loose throw rug with the Dyson last night. It jammed the brushes which stopped spinning, Once I removed all the entangled fibers the motor won't turn. The vacume still sucks, but the brushes don't spin I'm concerned I burnt up the motor for the brushes


Have you checked the belt? You can do so by removing the bottom plate from the power head. Once removed, check the belt. If broken or worn, it needs replaced.\015\012An instruction video for replacing the belt can be found on the below link. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I cut all of the hair out of the bottom of the spin-brush on the Dyson Upright Animal Vacuum. Now I dont think I can get the brush back in there correctly. If I squeeze it in there (which it is a VERY tight fit...) then it wont spin. Any thoughts?


Check the roller ends for dirt build up, they pull off and you should be able to clean them out.\015\012The roller should just go back into place if pushed together. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My dyson dc animal's brush is not spinning. The machine smells like burning rubber. I believe the clutch has gone out but the machine also only sucks from the top of the hose in the handle. I am wondering if the machine is not locking properly which is causing the brush to not need to spin. If this is the problem how do i fix this problem.


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The brushes have stopped spinning,how do i get them to spin again on my dyson slim? We have tried the brush button


One possible problem could be a worn clutch. I just had the same problem. Before buying a new clutch assembly, I took the out the clutch just to make sure I could do it (the link previously mentioned is great: ... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow

Just purchased this Dyson dc24 today. brush doesn't spin after gettin tangled in a cord. removed the cord from the brush OK. I have several times: removed the brush and replaced it OK. pushed the red button by the brush. pressed the brush power switch.


When you removed the brush roller dod you examine the end of the actual roller that is opposite from the removal opening. There is a gear that the roller fits over that may have gotten stripped when it became tangled. Check that the gear has not roun ... Dyson Ball DC24 Bagless Upright Vacuum

Why would my dyson dc 17 brush motor be extremely loud, but sound normal when brush is not spinning?


Could be the bearings on the end of brushbar need replacing,or it may be the clutch needs setting , lower the handle down to the floor then up again do this about three time to reset clutch.... ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My Dyson DC 14 is making the horrible "ratcheting"sound only when the brush is engaged on the carpet setting. I have cleaned the brush, so there are no obstructions, the canister is empty and properly on the unit. I checked to make sure all of the "traps" and hoses are clear of obstructions, the belt is on the brush securely and moves freely, the brush itself spins freely, but there is still the "ratcheting" noise. Any other suggestions?


Our DC33 was making the same ratcheting sound immediately upon placing the cleaner/brush head on the carpet. We carefully pulled the beater/brush bar out of the vacuum. Once removed, we pulled the black plastic end off of the center rod. We discovere ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Dyson DC 28 brush bar wont spin


... Dyson DC28 Animal Upright Vacuum New DC 28 Animal

Dyson root 8 cyclone brushes don't spin.


Try this link below for helphttp://www.fixya.com/support/r6551937-fix_re_dyson_dc08_turbine_head ... Vacuums

The brush bar wont spin on my dyson dc 25... i


Hi its Darran at Dyson.Simply switch the machine off and stand it upright. Press the brush bar on/off switch once and then turn the machine back on. When you release the machine into the vacuuming position, the brush bar shoul ... Dyson Ball HEPA Upright Bagless Vacuum - Iron/Satin Yellow

The brush on my Dyson DC-14 wont spin


Hello, have you checked to make sure you have nothing wraped around the brushes ? also it sounds like your belt needs to be replaced. ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Cleaned the brush bar but still not spinning DC14 Dyson


The belt is broke. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dyson Ball DC24 brush is not spinning properly...


Check it out with dyson, they might have others with this prob, just might be under warranty or be a recall.. ... Dyson Ball DC24 Bagless Upright Vacuum

Ve a dyson dc05 turbobrush cylinder hoover and have replaced the floor brush but the brush doent spin? What could be the reason please?


... Vacuums

My Dyson DC 14 brush does not spin - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum


It sounds like a worn belt or broken belt. The belt should be fairly snug. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Dyson D25 I was vacuuming and got the cord tangled inside the vacuum dyson 25. We opened it and was able to remove the cord. But the brush stopped spinning when I use the vacuum.


Hi there,Your DC25 is equipped with a sensor which shuts off the brushbar if something jams it. Please follow the steps shown in the video below to reset the machine after checking for any remaining obstructions. You may also want to refer to ... Dyson Ball DC24 Bagless Upright Vacuum

I was vacuuming with the Dyson DC 17 and sucked up a berber carpet string by accident and after cutting and pulling it all out of the bottom brush part, the brush no longer spins but the suction part works. What do I do?


The belt could be snapped. If this model has a brush protected belt then it has to be repaired by a service call. If however you can get to the brush roll belt by removing the bottom sole plate (turning over the vacuum so that you're looking at the b ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Brush doesn't spin. no suction felt at brush - Dyson DC14 All floors Bagless Upright Cyclonic Vacuum


Check that the brush has not become fouled with string, etc. If it still doesn't work try the following.\015\012\015\012Some Dyson's have a switch for the brush on the front of the handle. If yours does, please make sure its on. This m ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Poor Suction Heya! So I just picked up a used Dyson, but when I vacuum with it, the suction is pretty weak and it spits all kinds of stuff out the back and into my feet. When I pull the hose I have good suction, but in regular mode it hardly picks up anything. The brushes are spinning, and it eventually will clean an area if I go over it again and again. Maybe a clog somewhere? Please tell me that Dysons have better suction than my $50 Dirt Devil! Thanks!


I recently bought a second hand Dyson DC07. Its suction was poor. I removed all the un-clipable pipe bits and to remove any blockage but it all looked clear. The Final Sponge and hepper filter did have a lot of dust in it and the rotating brush was f ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My dyson is not sucking. There is no clog and the spinning brush on bottom is spinning.


Even though the brush is spinning, you probably need to replace the belt because it is stretched. It is probably slipping on the beater bar. bbDo you ever smell rubber burning while vacuuming? If so, it is the belt.Jim ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a dyson - bought it 3 yrs. ago and the roller brush stoped working - doesnt pick up anything. Can you help? The brush doesn't roll or spin. Where can we take it to be fixed and is it under warrenty? THis


Don't worry it's probably just that the belt has broken or stretched. Your actually supposed to change them yearly. So if its been three years thats probably the case. Here is a link to the belt you need and a manual with instrutions: ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have the Dyson DC14 and its like it's not brushing the carpet anymore, The brush is spinning, but its like it isn't self adjusting to the carpet height? It still has suction, but doesn't make the same sound it used to when you'd start vacuuming. Its like it never adjusts anymore???


Hi its Darran at Dyson.It sounds as though the internal hose underneath the machine has twisted slightly. With the machine switched off, lay it on its side and look at the base. You should be able to see a small corrigated hose. Simply t ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My dyson dc07 brush bar seems to be only spinning at half speed. Leaves three light streaks in the vacuum marks like somethings just dragging. Brush bar is clear and filters are clean. Seems like there's slipping somewhere.


The belt is stretch and so it is slipping on the motor shaft. You need to change the belt. Here is a link for the\015\012instructions on how to change the belt and a link for the belt you need: ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My dyson dc07 brush is not spinning - Dyson DC07 Bagless Upright Cyclonic Vacuum


... Dyson DC07 Bagless Upright Cyclonic Vacuum

Just purchased my Dyson Ball DC24 less then a month ago. Its great when it works. The brush does not spin. At first I was able to get it working after repeatedly pushing the brush button and fooling around with the handle position. Now nothing.


If its still undr warrenty take it back i wonder if the switch is broken or a bad connection .i hope this works thanks ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0474 seconds