Having problems with your Dyson DC14 All floors Bagless Upright Cyclonic Vacuum ?

My roller bar wont spin the belt is on though


Answers :

Even though the belt is on and intact it still can be stretched and worn. If that is the case it won't be able to turn against the resistance of the carpet. Your particular model has (2) belts, a clutch belt and a drive belt. Both should be replaced yearly. You can get them here:

Dyson DC14 Replacement Belts
Repair Help & Product Troubleshooting for Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My roller bar wont spin the belt is on though


Even though the belt is on and intact it still can be stretched and worn. If that is the case it won't be able to turn against the resistance of the carpet. Your particular model has (2) belts, a clutch belt and a drive belt. Both should be replaced ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Beater Bar The "Beater Bar" or roller with brushes on it, is not spinning, therefore not picking up. I cannot locate my manual and need to know if it is belt driven and how to get at the belt to identify the size and purchase and install a new belt. Thank you for any assistance. [email protected]


Take off the bottom plate, then you can get to the brush roll and belt, on the model number plate, the number of the belt is on that, it is also on the belt if you can still make it out. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down....when upright it won't spin! I cleaned any and all hair from the roller....belt is not broken....but do I need a new belt though? The vac is a few years old bever replaced the belt yet.


You need a new belt. ... Vacuums

The roller is not spinning. I took the bottom screws off but and replaced the belt but am not sure how to replace the clutch. I think that is what it is anyways, the thin silver bar that controls if the roller is spinning or not


... Riccar 8850 Vacuum

Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the


... Dirt Devil M088905 Vision Bagless Upright Vacuum

The belt burnt out and it seems as though the red arrown does not release the belt. Like it is backwards from the green arrow. It had a burning smell and the belt broke. Then the second belt started to burn out when the brush roller wasn't spinning. Not sure what might be wrong. Green light will not come on either.


It sounds as if there may be a piece of the broken belt in there. Look carefully with a flash light and remove any remnants you find, using a pair of pliers if you have to.\015\012\015\012Also, remove the entire brush roller assembly and ... Kirby Ultimate G Bagged Upright Vacuum

Roller bar does not spin


... Vacuums

Brushes wont spin ,even though the belt is intact


The belt can develop a worn spot. It will be intact but not spin. Replace the belt and make and remove any hair or other garbage from around the ends of the brush bar. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

We have a new hoover bagless that is a couple months old. The pet hair attachment stopped working. I disassembled it found lots of hair wound around the various rollers and removed - painstakingly thorough i might add. Problem is the brush still wont spin and now the belt seems loose - I think I put it all back together correctly but wondering if there is a trick to this?


Without the model number, I can't look it up, but this has a 1 years warranty on it, maybe take it to a warranty shop. Just take proof of purchase, model and serial numbers. ... Vacuums

I have a eureka 4351 and I think the belt is broken but I can't figure out how to access it to check. Roller brush doesn't spin though. Just need to get the silly thing apart.


... Vacuums

Hello, I have a Riccar 8000. The belt works, the bar spins, and it will **** things up. However, it will not pick up threads and dog hair or anything from the carpeting. Mu husband took the bottom off and there were a couple of small parts on the plate. We have no idea where they belong. Could not see them in the photos in the manual. Could it possibly need a new roller? Any help would be most welcome. Thank you! Mary Simon


... Riccar Vacuums

The bar that the belt sits on wont spin and smells like its burning when you turn it on. Is the motor out?


Hi,No, it is not the motor, it is a bad belt or something is jammed causing the belt to slip...\012Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

My vacuum has not been running right..the beater bar is not picking up and the rollers aren't spinning...the belt doesn't need replaced so what else could it be...everything else seems to be running fine???


The motor shaft that spins the belt may have hair wrapped arount it, causin the belt to slip. You can't miss the burnt odor.\015\012Remove the belt and clean the motor shaft. ... Vacuums

Changed belt in hoover windtunnel t-series not beater bar wont spin when vacumming


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Belt keeps sliding over on the roller bar and rubbing on plastic parts. Belt is a "U" belt and I am told it should be a "R" belt. Sears sold me a "U" so I will try and find the R tomorrow. What keeps the belt other than tension from sliding onn the roller bar? Could it be that just the wrong belt could cause this??


The 4870 Series uses Part number 61110. It is a "R" Belt. It will appear too be to large. This is normal. ... Eureka Smartvac 4870 Bagged Upright Vacuum

I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel


The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums

Roller bar does not spin


I have the same problem ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

My electrolux canister vacuum roller does not spin even though it has power.


Take the floor attachment and on the front where you attach the wand there's a rubber like cover take it out,then you'll see a screw that you would need a star key driver,loosen it and the cover comes off,you'll see 2 wires,black and red,on mine the ... Electrolux Guardian Bagged Canister Vacuum

I have a Eureka 5902AVZ and the brushroll does not work. when i remove the belt, which is not torn nor worn out, the motor spins perfectly fine. Though when i put the brushroll back into place, it shows that the motor is trying to spin, but with resistance. it seems the brushroll will not spin if locked into place, because there is no attachment on the left side of the brushroll that will allow it to spin freely with the belt. am I missing some parts or is there something else wrong?


Hi and welcome to Fixya. I am Kelly. \015\012\015\012You have correctly identified the problem as the brush roll itself. \015\012\015\012There is a bearing under each end cap of the brush roll. You can gain access to the ... Eureka 5902AVZ Bagless Upright Vacuum

Roller wont spin


The bearings in your brush roll are bad. Replace the roller and walla problem solved! ... Bissell CleanView II Plus Upright Bagless VacuumVacuum

Beater bar not spinning on my dyson animal DC14. Motor turns on and sounds good. My belt is not broken, and still tight on the bar. It looks like another possible belt or gear box between motor and bar. Can anyone please point me to next step?


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Hi,dyson dc25 overdrive,my brusher's wont go round,i have cleaned the brusher's and filter,loads of suction.the belt is intact and the roller move's feely by hand,could it be the switch


Hi Stephen,I'm sorry to hear you've had difficulty with your DC25 Overdrive. If the brush bar won't rotate, and you've already checked the cleaner head is free of obstructions, it's likely it just needs resetting.You might like to tak ... Vacuums

Caught a string in the beater bar. Cleared it out but now the beater bar will not spin. The belts are intact. I had this problem before and I can not find the answer online that fixed it. It is not the belt.


Hi there,Sorry to hear you're having a problem with your DC07. Please note that the brushbar will never rotate when the cleaner is standing in the upright position, or if you've used the brush control to turn it off. If you ha ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The bristles wont spin the belt seems in tact yet it wont spin


... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

The bar brush does not spin. I opened the vacuum head and the drive belt to the bar brush is loose. I don't see how you remove the slack from the belt.


You have to have it in the carpet setting in order to put pressure on the v-belt. there is no way to tighten up the v-belt, but i would try to replace the big flat belt. if you haven't changed this belt in over 6 months, i would change it. ( on avera ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0618 seconds