Having problems with your Dyson DC14 All floors Bagless Upright Cyclonic Vacuum ?
My DC14 (not animal version) has 3 major cracks that have pretty much killed the thing. There are three 'columns' that run down from the handle to the base. From the back, the left one has either the intake or outflow for the canister and the right one has the reverse. The middle one is where the base of the extension hose and cord is mounted. On all three the plastic has cracked at about the point where the bottom of the canister meets the permafilter. The vacuum is useless now and
I'd suggest using an epoxy cement (3M makes really good stuff) The epoxy comes in 2 separate tubes or bottles. Each alone will do nothing, but when combined become incredibly strong. Use care when using since once combined you only have a short time before it gets hard as rock. Do a little at a time and you should have no problem.
Repair Help & Product Troubleshooting for Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Hi: My DC14 (not animal version) has 3 major cracks that have pretty much killed the thing. There are three 'columns' that run down from the handle to the base. From the back, the left one has either the intake or outflow for the canister and the right one has the reverse. The middle one is where the base of the extension hose and cord is mounted. On all three the plastic has cracked at about the point where the bottom of the canister meets the permafilter. The vacuum is useless now and
I'd suggest using an epoxy cement (3M makes really good stuff) The epoxy comes in 2 separate tubes or bottles. Each alone will do nothing, but when combined become incredibly strong. Use care when using since on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
Hello, I have a Kenmore Progressive Canister Vacuum 116.20912006. It won't turn on. On the hose assembly, the end where the hose swivel is, there are 4 metal pins that plug into the canister. One of the pins looks like it broke off. There are only three pins remaining. I assume there should be four pins as there are four holes. Is this the problem and is it fixable? The vacuum is from 2002 so I am not sure a replacement part is even available and at what price. Thank you. Susan [email protected]
Hi Susan, if the pin has broken off you can do one of two things, first, would be to find a local vacuum repair shop and take it there for them to look at. they may be able to look at the hose and fix it for you pretty cheaply. what ... Kenmore Progressive 20912 Bagged Canister Vacuum
How do I attach the rainbow mate to the rainbow canister or wand? I have the D4C model, My electric hose is original but does not have the grip handle. Does that matter? The cord is so short it cant just attach to the canister right? thank you very much.
... Rainbow 75th Anniversary Canister Vacuum
I'm trying to change the filter....One person told me to open the hose end and take the bag out and go from there, but that isn't the right way!!! It's the other end where a couple brushes are able to be stored on top of the canister, but I can't figure out how to get that section off..it's as tight as a drum HELP PLEASE and thanks. Betty
There's a tab at the middle of the lower back of the tool holder (air diffuser). Pressing in on that tab should enable you to lift the back of the holder first, then lift off the whole thing. It will come off, just make sure the tab is in far enoug ... Electrolux Epic 6500 Vacuum
GE canister 106766 Power cord does not stay in bezel
Yes you are absolutely right.you would save on shipping cost if order both together.\015\012\015\012and for parts you can also order it from \015\012www.radioshack. ... GE 106766 Bagged Canister Vacuum
My Hoover Whisper Cyclonic is collecting the dirt but not taking it into the cylinder. The brushes were at one point starting and stoping due to the belt periodically turning,now the brushes are turning and the dirt just collects and I'm starting to smell a an oder like rubber burning.I've taken it apart and tried to make sure the is no clog. The one hose that I can't check is in the back right base, above and left of the right back wheel.
... Hoover U5753-900 WindTunnel Bagless Upright Vacuum
Hello, I have the same model. And though it is three years old, starting from the last month, it does not clean anything anymore. Cannot even pick up one single thing from the floor. Every dirt gets stuck in the hose. I cleaned the hose and cleaned the filters but it still does not pick anything up. Is three years its normal lifetime or do I have the change the filters, instead of cleaning them? Thanks.
I know bissell vacuums are very cheap but they should last more than 3 years. there should be two parts to the dirt cup. remove the dirt cup and above it there should be a round plastic part. unscrew it and check that filter. ... Bissell 6594 PowerForce Bagless Upright Vacuum
Have a Kenmore Model 116.25512. Just sucked up dolls clothing (satin pajamas) and it's stuck in the hose. Put a wire hangar down the hose, can't nudge it through. It's right in the middle of the hose. What to do?
... Kenmore 25512/ 25513 Progressive Canister Vacuum
DC07 DYSON REPLACEMENT HOSE. HOW DO YOU REMOVE IT FROM THE HANDLE. I have a kenmore whispertone 8540 canister vaccum. The electrical wires (3) to power the beater are embedded in the hose, in a spiral fashion. The yokes that hold the hose on both ends (and attach to the beater on one end and the unit on the other) have no screws or pressure latches; i don't want to use brute force as i may damage the attachment device inside the yoke. If someone can tell me the trick to get these yokes off each
Should be a pry off dot on the underside revealing a screw ... Vacuums
Hot cord the cord on my vacuum cleaner has been getting very hot the heat is from one end to the other incuding the plug and also where the cord exits the back of the canister please help I love this vacuum cleaner it has been faithful to me for over 15 years!
Likely after all these years that the motor is starting to go bad and draw more amps thasn it should. a new motor at a vac dealer is your best bet. it was likely made by panasonic, so a new panasonic is your best bet, and less $$$than the kenmore for ... Kenmore 23313 Whispertone Bagged Canister Vacuum
I have an aerus electrolux guardian canister vacuum. The cord was damaged but the retraction winder is still fine. I have ordered a replacement cord but I have no idea how to remove the old cord and install the new one. Am I over my head?
The winder is activated by a coil spring located in a drum. The drum transmits the power from the wire with 2 circular contacts. To replace the cable you must dismantle the case to access the drum, take the spring pressure out carefully as to not let ... Vacuums
I have an Aerus Guardian canister vacuum with a clogged hose. The tiny stuffed animal toy is lodged right below where the swivel handle meets the hose. Switching the air flow does not dislodge it. I would like to remove the handle from the hose. Any suggestions?
Consider this. If your vacuum is still under warranty, removing the hose will void the warranty on the hose. I strongly recommend calling an authorized dealer/consultant.\012Although it may seem to be fairly simple to remove the handle, there ... Electrolux Guardian Bagged Canister Vacuum
Electrolux Centralux I have a Electrolux Centralux. When I plug the hose in at one of the wall outlets the motor will not start. If I go to the motor and slap the unit it will start.....then...it will not stop unless I unplug the power cord to the motor. If I plug the power cord back in, the unit will not restart until I slap the motor unit again. The unit has only been used 20 - 30 times. Any suggestions?? Thanks, Bruce
I dont know if you had your unit looked at yet but it sounds like the Power module is going. I repair the machines so I know some of the work. ... Electrolux Centralux Vacuum
Lost suction I've only used this vacuum a few times, it's practically brand new. Now, one I turn it on, it sounds fine, and the hose feels as if it's getting some suction, but it's not strong enough to actually **** things up from the carpet into the canister. I have completely emptied the canister and bought a new filter. Nothing seems to help.
TOSS IT and forget it! I have never used a hand vac that worked that was worth the effort of turning it on .... I suggest they are all junk ... I found very few vacuum cleaners ... actually **** especially anything made by dirt devil ... I do have a ... Dirt Devil Vibe AllPurpose Hand Vacuum Bagless Vacuum
If my system is stopped up will it make a noise inside when i plug in my hose it makes one out side at canister but not at my wall hose
Yes. A clog will cause the motor to work harder resulting in a higher pitch. To prevent the motor from burning out the clog needs cleared ASAP.\015\012This could be something as simple as cleaning the filter, but it could also be a blockage i ... Broan-NuTone VX475 Bagged Central System Vacuum
I have a Kenmore 116.36932 (upright-bagless vacuum) that the motor protector by-pass valve has opened. I've clean out the area between the agitator brush where the flexible extension hose starts. There was some blockage there. I checked the rest of the system (extenstion hose, back filter area, pipe area to canister and area to side filter. I took the 2 filters out and the by-pass valve is still open. Where else could there be a blockage that I can take apart to clean and put back together
Dyson DC 14 hose has no suction, with or without brush attachments. Hot air shoots out from the base of the canister when I try to use the hose. I cleaned the top filter, but can't figure out how to remove the hepa filter to clean it without destroying the case. It looks like it might take three hands to insert pennies and "flip" the case open as is suggested on a youtube video for a different model. Would this even help, assuming I could get the thing open?
... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
I have a cannister (Animal something...) Today, it didn't sound right - like a blockage. I took out the filter - seemed OK; I looked for a blockage - found none. I continued to vacuum, but it wasn't picking up. Then, I stopped again, and I found a blockage (cat toy mouse) right at the end of the hose (attachment end.) I cleared, and I turned back on - nothing. Completely dead. It is one year old, just about exactly. Desperate, Sharon Tracy
Hello,if your canister is completely dead, then it means its having a power problem. You need to focus your attention on that part of your canister that relates to power. Such as; power wire, if you don see any fault with the power cord, ... Dyson Vacuums
I bought a Kenmore canister vacuum, model 116, in April 2007. This morning, the sound of the motor suddenly began to deepen, and I began to lose suction. Normally, if something is clogging the hose, the motor will wind up to a higher pitch, not a lower one. The filters are clean, the bag is empty, and I can't detect anything lodged in the hose. If this were a car's engine, I would say it's "lugging down". Any pointers?
Okay, bear with me. Is it possible you have a suction adjustment, dial somewhere on vac. Check and see and if it does, be sure it's all the way up. Also, try removing hose and run a broom handle fr. one end to the other...BUT be careful not to stretc ... Vacuums
Took my Miele Solaris canister vac in for repair as it wouldn't turn on. The repairman said to come back the next day for the estimate. I called and he said I needed a new cord reel and it would be $189. I drove to his shop and said I would wait to do it later, that I wasn't ready to spend that much. When I came home, it started right up but has no power and doesn't sound right, the noise of the motor is real soft, not as loud as before. I have this terrible feeling that when we decided not to
When you say 'has no power' do you mean , no suction? He may have left the suction hose of the motor and that's why it sounds different. I would call him back and request that he put the machine back to it's original 'state' as it was when you brough ... Vacuums
Roaring vacuum My vacuum begins to roar shortly after I turn it on. The sound seems to be coming from the middle of the canister. When I take the recoil cord off, there is a plate just under it still on the canister that is extremely hot. Any idea what could be wrong and how to fix it?
Good day,your problem seem that it is plug if you have no suckiong ,place the hose on the exaust that should un plug the hose,or the motor has had some dirt et it and plug the intake ,that is why it roars try this,later ... Electrolux UltraLux 2000 Bagged Canister Vacuum
My electrolux oxygen canister cuts on and off. I have to open and close the vacuum, or take the base of the hose off and then re-insert. I have to do all these things before it will start up again. I sometimes shake the hose around, then it will come back on. If I try to dust with the dust brush (like a lamp shade or shelf) and the suction pulls against the object, the vacuum goes off for awhile. Sometimes I'll have to reset the vacuum by unplugging the electric cord. I never get to finis
Maybe you should have taken it back to that shop, it appartently isn't fixed. I would have replace that board, don't believe in modifing, you usually end up with other problems, like you have. One thing to check is maybe you have a partial clog in ... Vacuums
My infinity vac NV29 seems to have an extension wand stuck down in then tube and I am not able to get it out. We rented our winter home and evidently they found some type of extension that did not belong to it. Is there a way to take the handle apart in order to remove it? I am not able to use it with the handle and have to use the one on top of the canister, which is extremly difficult for me since I am disabled. Thank you.
... Euro-Pro Vacuums
Kenmore 21875 One day it's working fine. Next day, it won't turn on. When I attach the hose to another vacuum cleaner, it runs. Is there a reset button on the canister? Could it be the receptacle is bad? My Kenmore Progressive won't turn on today either -but was fine last week. I cleaned the filters checked for blocked air, tried a different outlet and no luck. I'll check the pins on the connections and see if one of them is not matching up or appears worn.
Give the prongs a wiggle and see if there is any play in them.Might just be a plug end. ... Kenmore 25512/ 25513 Progressive Canister Vacuum
I was given a model 6591, plugged it in and it worked but didnt "****" and didnt sound right. I turned it off and removed the hose from the back found a badly plugged hose. Removed the hair plug cleaned filters and when I tried to turn it on again. Now the motor will not turn on or even make a noise. I hear there is a fuse that can be blown? How can I find the fuse if there is one? Thank You Ron
The User Guide for the bissell Clearview Power Trak\012\012http://canada.bissell.com/images/UserGuides/3590C.pdf\012 ... Bissell 6591 Power Trak Revolution Bagless Upright Vacuum