Having problems with your Dyson DC14 Animal Bagless Upright Cyclonic Vacuum ?
Machine turns on, has little suction, then stops working.
\015 While using the corner of a rug got sucked in, machine was turned off.When using it a few minutes later it just stopped working, The next day it turned on, had very low suction and quit working after a few minutes.\015
It would be helpful to know what model of vacuum cleaner you're talking about. Basically though, your machine has a blockage somewhere (hence very low suction), and is cutting out after just a few minutes because of overheating. You need to explore the suction hose (or whatever your machine has), find the blockage and remove it. Blockages almost always happen where the pipe-work takes a sharp bend. In the worst-case scenario (although in almost all modern machines this is not possible) the blockage may be in the vacuum fan enclosure itself, and then you'll probably need a professional to take care of it.
Repair Help & Product Troubleshooting for Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Machine turns on, has little suction, then stops working.
It would be helpful to know what model of vacuum cleaner you're talking about. Basically though, your machine has a blockage somewhere (hence very low suction), and is cutting out after just a few minutes because of overheating. You need to exp ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.
... Hoover U6485900 Bagged Upright Vacuum
Suction stopped. Roller and belt working-in fine order. Checked hoses have not found any blockage. Blowing out air or sucking so little can't feel it with hand on hose end. Help!
Either a blockage or the main air filter is blocked , some it can be washed and others it must be replaced I would check the owner manual and look at the filter, foam ones can and usually have instructions where they install to wash them. ... Hoover Tempo Widepath Upright Vacuum - Blue
My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old
Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
I have a Kenmore Elegance Vacuum with Dirt Sensor, Model # 116.30750400C, Serial number M41901532. When vacuuming the carpet the power head will work for 3-6 mins then automatically shut off, power is still there and lights work but the power head motor turns off and the suction stops. I will turn it off and on, check the outlet, flick the on off buttons...nothing. I will turn it off for a couple minutes and it turns back on and runs like normal. I've check the bags, filters, cleaned the hos
It is an electrical problem in the handle, if you can or know somebody that has any fix it ability it can be fixed in about ten minutes. Oh, and Sears SUCKS!! ... Kenmore 34612 Bagged Upright Vacuum
Hi. I have Dyson dc08 hepq+. Thet problem is its not having suction .I checked inside the pipe and foot , ery thing is fine. And if i take the whole dirtbin out ...machine workes fine. when i put ery thing back ....as soon as i start it , after 2 second machine change its voice...and loos suction. I think its just happen because ...the saftey yellow valve inside the machine turns up because the dirt drum is blocked inside some where. Any suggstion ...what can i do with it. I m tahnkful in avance
Hi its Darran at Dyson.From your description of the problem, it sounds as though the bin inner is missing. To confirm this, if you remove the cyclone and bin from the machine, then separate the 2 pieces as if you were going to empty it, w ... Dyson DC08 Hepa Allergy Bagless Canister Cyclonic Vacuum
My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc
... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum
I have an electrolux renaisence vacuum. the brush in the floor attachment turns but I have no suction. When I change to bare floor option on the handle the brush stops turning (correct) but I still have no suction. The lights on the handle showing --floor,carpet, high and low all work.
Sounds like you have a clog, either in the hose or the inlet by the brush roll. ... Vacuums
Hand held vacum suction stopped after 1st use. Was working fine, suction does work if onfloor but won't once turned to tool
Go to the web page and see instructional video and maintenance helphttp://www.bissell.com/how-to-videos/God bless you ... Bissell 2X Proheat 9200 rug cleaner
Low suction I have a Hoover central vacuum system. I've reset the fuse box, checked the fuses, all of the lines are clear and there are no holes for escaped air to travel out. The filter has been cleaned as well. The vac works well with high suction when hooked directly to the unit, however when using any of the indoor connections there is extremely low suction. The machine still turns on so I do not believe it is an electronic issue. I have troubleshooted the issue as best I could and would
... Hoover L2310 GUV Central System Vacuum
My eureka optima upright bagless vaccum has VERY low suction using the floor part. the hose has excellent suction. i removed the little translucent door underneath and there were no blockages, i cleaned the brushroll thoroughly and that hasnt helped either. i know this probably isnt recommended but i turned it on to the floor setting with the brushroll off and stuck my fingers up the intake as far as i could, the suction was good further up but it just seems to stop down at the base. because i s
I will try and help here. Is the sole plate on the bottom of the vacuum complety on and there are no visible cracks along the seam where it meets the body? This is the usual cause for this. Onc you take of the plate to access the roller and brushes, ... Eureka 431A Optima Bagless Upright Vacuum
We have a series e rainbow cleaner. my wife had been using it i turned off and turned the canister up sie down to get the serial number. it would not turn back on.we need a new hose and thats why i was looking for the serial num. it has a rocker switch and the motor will work on low but will not run on the suction side. i have checked the wiring harnesses out as best i could without taken it all apart. im wondering if it may be the switch. it started once and then stopped.
There is one way to verify if it is the switch.It's kind of dangerous though,but not too bad.You need an extra piece of wire,fairly thick.I would use 4 guage myself.Hold it with pliers,just in case it gets hot.Turn the switch on and hold the wire to ... Rainbow Vacuums
My hoover carpet cleaner does not extract water. The brushes stopped turning since more than a month and now it doesn't extract any water. The engine is turning on but it does not work properly. I've checked for the solutions to this problem in the manual but any of the causes listed there apply to my machine. Thanks for your help.
... Hoover F5826-900 SteamVac Upright Wet Washer
Electrolux canister model #1205. worked great. got a new hose and if you check the suction with your hand, great suction, but then the check bag light turns on and machine shuts off.
... Electrolux Vacuums
Electrolux vacuum model #1205. worked great . then got a new hose and if you check the suction with your hand, great suction, but the check light turns on and the machine shuts off.
... Electrolux UltraLux 2000 Bagged Canister Vacuum
I have a DC14. About a wk ago it was making loud sound and bar stopped turning. i unclogged everything....now the suction works great. However, the bar still wont turn. The belt inside is still intact and isnt loose. Several solutions suggested resetting the "Red" button...i have searched the vacuum over and over. there is NO red or any other color reset button. The bar is set down perfectly in there, the cover plate is installed properly. What other problems could there be? Or do i just need to
... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
I bought a used Hoover Reind and there are two issues:1) There is no suction. The debris flies out of the back of the machine and 2) The machine will not shut off. You have to unplug it in order to get it to stop working. Any suggestions on either problem?
... Hoover U5507900 Elite Rewind Bagless Upright Vacuum
On/off switch we have two of these vacuums at work, and both of there on/off switches dont work too well. its hard to explain, but when u normally turn it on or off theres a little resistance in the switch and you hear a click, with both of ours the switch moves freely back and forth from on to off, no resisntace, no click, and the machine doesnt stay on, or off for that matter. the switch just moves back and forth.
... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum
The motor works, suction is good, but the roller brush will not keep turning. It turns at start up, then stops a minute later.
... Euro-Pro V1828 Shark Stick Vac Bagless Vacuum
My Dyson animal seems to have an electrical issue that I am unable to pinpoint. Neither the wand nor the floor vac have any suction AT ALL. In fact the vac makes absolutely no sound and you wouldn't even know that it had power to it unless the rollers are turned on, the rollers work just fine. I had this problem start about a month ago and then it just started working again after messing with it for a while, now it has happened again and I am getting a little agitated! Please Help!!!!!!!!!!!
There is a filter inside the canister, and by your description it sounds like it needs to be cleaned. if you remove the filter and blow it out using a air compressor or using a slightly ridged brush and tapping the filter out this should solve your ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
My G6 kirby stopped working. i have checked the wire for fraying and continuity and found no problems. I have noticed that the foot pedal that turns the machine on doesn't seem to click when pushed on or off either. i have the motor exposed now to check if it is bad, but i am not sure how to pursue doing just that.
... Kirby G6 Bagged Upright Vacuum
My Dyson just stopped sucking up dirt. I have checked all the obvious things like clogs and filters. I noticed when I turn it on, there is a valve on the top of the cannister that opens and you can feel suction from the vent hole. Is this valve malfunctioning, or is it working correctly because something else is malfunctioning?
Your cyclones could be clogged. You can clean them yourself pretty easily. See this video. http://www.youtube.com/watch?v=2OO3ugkyzxk ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
I have an older Wega 2 group espresso machine. Looks like a date of 1992 on the group head, but not sure. This has no model name that I can find. Anyway, when I turn it on I get all lights flashing after it heats up 5 minutes or so. I do get nice steam from the wands. I drained teh tank and found a little scale, but not much. I took apart the group heads and cleaned them thinking it may be a clog there, but that doesn't seem to have worked. Also fwiw the water level float is not visible and whe
For a new fridge, need more time to maintain the required temperature of the fridge abut mainly the goods in it? So everything seems normal. The time will be reduced day by day since the goods will stay for longer time in and door opening will bec ... Vacuums
My Bissell model 8910 pro heat will pump solution or water for like the first couple times you pull the trigger as you can see the mixture window spinning. After that it stops spinning and nothing else will come out until you turn the machine off, and restart. Then again same process works for a couple trigger pulls then quits.
Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum
I turned the vacuum on, it worked for about 1 minute, and the big brush stopped going around. There IS suction in the hose.
There are a few things to check. There is a small belt that spins the brush. If the belt breaks then you would have this problem. With the vacuum off, turn the vacuum over and see if that is the case.Also be sure that the tubes and flexible hos ... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum