Having problems with your Dyson DC14 Animal Bagless Upright Cyclonic Vacuum ?

Beater bar belt needs replacedon a dyson DC14 animal

\015 I cannot figure out how to replace a broken beater bar belt on a dyson DC14 animal. can anyone help me out here?\015

Answers :

Remove the glide plate at the bottom of rhe machine. Remove brush and broken belt. Fit new belt and re install brush. Fit glide plate, job done.
Its in the instruction book

If your Dyson is more than 3 years old and the drive belt is still attached to your brush roll, The most likely cause is a stretched belt slipping on the clutch. your brush roll encounters friction on the carpet and if there is not sufficient tension in the drive belts, you have 2 of them, then they will slip and you cannot pick up debri as the vacuum was designed. You have a few options, call the Dyson help line located on your vacuum via a sticker behind your hose; explain to them the problem with the brush roll not turning sufficiently. There are also replacement belts available for your model at a cost of around $10 depending on your area, but you have to take the clutch assembly apart to install the new belts. Lastly you can buy a new clutch assembly for about $70 but this is a last resort idea. Any reputable service center should be able to replace a clutch in 5 min. and rebuild one in less than 20 min.
Hope this helps.
Repair Help & Product Troubleshooting for Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Beater bar belt needs replacedon a dyson DC14 animal


Remove the glide plate at the bottom of rhe machine. Remove brush and broken belt. Fit new belt and re install brush. Fit glide plate, job done.Its in the instruction book ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?


Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Beater bar not spinning on my dyson animal DC14. Motor turns on and sounds good. My belt is not broken, and still tight on the bar. It looks like another possible belt or gear box between motor and bar. Can anyone please point me to next step?


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Need to put on a new beater bar belt on my dyson 17 animal


Http://www.youtube.com/watch?v=Z1nSYmrLLsE ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

We have a dyson dc14 and the beater bar stopped turning, we cleaned the bar off and checked the belt and it's not broken, I know I called Dyson a year or two ago and they told me how to reset the beater bar motor but I don't remember exactly what I did, anyone know the answer to this??? thanks in advance....


Hi its Darran at Dyson.Check that the brush control dial is in the centre position when the machine is locked upright. When you release the head and pull the handle back this dial should mopve forward to the on position. Once here, the ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Removing cover over beater bar for cleaning on dyson animal vacuum. Accidentally ran over mess on carpet and need to clean inside of cover and beater bar. Thanks


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dyson Animal 07 beater bar not spinning - belt not broken


If your unit has a clutch it maybe that it is in the off position or the motor belt is broken your unit has to belts if its a clutched model  ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Belt how do you change the belt on the beater bar; dyson animal dc 07


Http://video.aol.com/video-detail/dyson-not-picking-up-dirt-no-suction-how-to-repair/2334249387 ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

How to remover beater bar caps dc14 - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The beater bar doesn't work - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum


You need to replace the belts. Here are the belts you need:Dyson DC14 Belts ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The beater bar is not rotating. - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum


You need to replace the belt that drives the beater bar ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Beater bar is slipping on belt on my Dyson DC17 animal


Beater bar was turning intermittently. No noise. Removed bar, disassembled ends and removed lots of junk. Replaced, and works like new, so far. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My husband ran over my daughters shirt with our Dyson DC17 animal. Now it's making this horrible load ratting noise. I've taken the head off. Clean the beater bar. The belt is in tact. No


First make sure there are not any of the rubber cogs missing from the belt, it may be wise to replace the belt anyway because the cogs may be worn. Make sure the brush roll does not have any play in it anywhere and that It fits tightly in the nozzle ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Hello. i only have one arm and am trying to figure out why my beater bar wont turn on my dyson dc14. the belt smells a little too. thanx, trixie


Sounds like the beater bar is frozen in place. This sometimes happens when the ends of the bar become stuck in the holders.\015\012The solution is to remove the beater bar and clean the small holders on each end removing any debris that has built up ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The beater bar will not turn - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum


Hi its Darran at Dyson.Make sure that the brush control dial on the cleaner head is in the correct position for use on carpets. It should be in the centre position when in the upright mode and then when the head is released into the clea ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The beater bar on my dc33 animal dyson won't turn, the belt is in perfect condition and there are no blockages or obstacles that will stop it from turning


... Dyson Vacuums

I was going to send my animal in for repairs but after waiting a week Dyson sent the wrong box. The beater bar only works intermittently and the thing roars.


Hi there,I am very sorry to hear you are having difficulty with your machine. I apologize for the error regarding your box. However, we would appreciate the opportunity to assist you further in this matter. Based on the details you provided, ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Beater Bar The "Beater Bar" or roller with brushes on it, is not spinning, therefore not picking up. I cannot locate my manual and need to know if it is belt driven and how to get at the belt to identify the size and purchase and install a new belt. Thank you for any assistance. [email protected]


Take off the bottom plate, then you can get to the brush roll and belt, on the model number plate, the number of the belt is on that, it is also on the belt if you can still make it out. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My dyson animal is hard to push on carpet - the beater bar is still operational. When I turn off the beater bar and run the vacuum on hardwood the beater bar stops moving, but it still ''rolls'' on the hardwood - it doesn't pull up like it used to. It also seems to not be picking up as well as it used to, although no blockages are present and the filter is clean.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My Dyson DC17 beater bar motor works intermittedly. I have to almost whack it on the floor to turn it on and then shuts off again. I have checked the belt and it is fine, also have checked for blockages. The switch to turn the beater bar on or off will not work when the beater bar motor is off. the suction is fine though.


Buy a Kenmore for less money ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The beater bar on my Dyson won't turn. The vacuum runs and suctions but the bar won't turn and the belt is not broke. The beater bar did get a carpet fiber caught and wrapped around it which stopped the bar and I removed the bar to cut the fiber loose and replaced it and now it won't turn


The belt doesn't have to be broken to make the vacuum not work correctly. If the belt is stretched the vacuum won't operate the way it is supposed to. You can get replacement Dyson Belts here: ... Vacuums

Correct position of beater bar on a Dyson DC14?


I had the same problem. I removed the brush from the machine. The brush should move freely when removed. If it doesn't move freely, pull the ends from the brush, both ends come off(one will have a rod fixed to it). I would suggest you clean the ends ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Changing the belt on a dyson dc14 - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Replacing clutch drive belt dyson dc14 - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum


Chris,\015\012I am just trying to find an owners manual, but I can not find one anywhere. Your link did not work. Can you help with another link? ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Dyson fan belt fitting. i've lost my manual for my dyson animal dc07 and need to fit a new drive belt. thanks in advance, alan


You can see this on utube video. help ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0904 seconds