Having problems with your Dyson DC14 Animal Bagless Upright Cyclonic Vacuum ?

The brush on my dyson dc14 animal will not rotate

\015 And there is a burning smell\015

Answers :

You probably have a broken belt. You need to take the plate off the bottom and see if the belt is broken. If so, contact Dyson (1-866-693-9766) to get another belt.
Repair Help & Product Troubleshooting for Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dyson Animal DC14 brush will not rotate. Removed


If this model takes a clutch then it is stripped and needs to be replaced. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The brush on my dyson dc14 animal will not rotate


You probably have a broken belt. You need to take the plate off the bottom and see if the belt is broken. If so, contact Dyson (1-866-693-9766) to get another belt. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have dyson animal brush does not engage - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum


Hi There, Ok so I have to ask the obvious is the dial set to 'carpet' assuming it is then there are only a couple of reasons why the roller would not spin. 1. Bearings in your roller are siezed and you need to replace them.2. The ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

How do I replace the brush on my dyson dc14 - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum


Hi its Darran at Dyson. If your DC14 has a brush control, we would only recommend that a suitably trained person attempts to replace the brush bar. We can arrange a repair so that one of our engineers can replace this for you, ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a dyson dc14. the brush bar will not rotate when the vacuum is running. the belt is attached and it will rotate by hand. when you switch from bare floors to carpet-the bar will not kick in and rotate.


\015\012Hi,\015\012Check that when you pull back handle to vacuum the clutch control knob which is located front lower left side of machine moves to drive position & is not stuck in off or park po ... Dyson Vacuums

My Dyson Animal has good suction and works fine for actually picking up dirt, but when I use the vacuum with the roller, I hear a grinding/rumbling noise. Its only when I use the vacuum with the brush rotating. It does not happen hen I shut the roller brush off. The belt is fine. I cannot figure out what is wrong as there are no clogs, debris, or foreign objects stuck in the brush or in the belt. The noise seems to be the only issue. The vacuum picks up fine. It just doesn't sound right a


Trace the path of the suction into the tank and see if there is anything loose or ingested.\015\012Also, remove the brush and clean as best you can. Perhaps there is something caught in it. Lubricate where it makes sense with some WD40. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Dyson dc14 Animal motor brush replacement


By the time the brushes are shot, so is the armature. You need a motor. ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My Dyson CDC14 Animal just started making a wierd sound coming from the rotating brush area. I already cleaned around the brush, sounds like a fast rattling sound.


Hello,Something could be jammed, or not rotating freely, maybe an improper alignment with the brushes, or a blocakage within them. Try to re adjust the brushes :) ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

While using my Dyson a rug got caught and that ratcheting sound started. I removed all signs of strings, etc until the brushes rotated fine but when I started the Dyson the ratcheting started again. I have the DC 14 Animal.


The rattly sound means the drive belt has snapped or the protective clutch has slipped. This needs repair by someone who knows how to repair Dysons officially. Sadly its the kind of model that can't be done by the owner. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Dyson dc30 brush bar not spinning - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Dyson dc 25 animal brush not rotating - Dyson DC25 All Floors Bagless Upright Vacuum


... Dyson DC25 All Floors Bagless Upright Vacuum

Dyson DC08 ANIMAL BRUSHES NOT ROTATING - Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum


... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

DYSON DC14 While vacuuming the living room, the rotating brush started making an awful loud grinding sound. We opened the intake port, cleaned the brush but to no avail sound still persists once you lower the vacuum handle in an attempt to clean. Was wondering if there was anything that can be done?


Take the bottom plate off and check the belt. Also, rotate the brush by hand - it should turn with only a moderate resistance from the belt, or very little if you take the belt off. If it is hard to turn, or if the belt is stripped-out right where it ... Vacuums

Dyson DC 25 Dyson Ball animal. The bottom brush is not rotating. I detached as and reattached as the manual suggested. Help Thank you very much


Two things you can do.\015\0121- Remove the brush as if you were going to change the drive belt for it.\015\012Clean the brush as best you can and spray some WD40 on the hard rubber/plastic\015\012pieces at both ends of the brush. Rotate the pieces ... Dyson Ball DC24 Bagless Upright Vacuum

My Dyson DC 14 brush does not spin - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum


It sounds like a worn belt or broken belt. The belt should be fairly snug. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The brush wont turn on my dyson DC 14 - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum


Sounds\015\012 as if you need to replace the brush belt.JimLet me know if this helps. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Dyson DC31 Animal rotating brush cuts out after a few seconds


... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

The brush wheel does not turn - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My Dyson DC07 Animal brush does not rotate. What can I do to fix this?


Hi.\015\012\015\012Try This site for help.,\015\012http://dysonmanuals.llc.nu/ ... Vacuums

Brushes not moving - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum


The DC14 has a "brush control system" operated by a knob on the right side of the base. This knob has two positions: "bare floors" (or "off") and "carpet" (or "auto"). The motor turns the roller only when the knob is on "carpet", and even then ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My purple Dyson Animal (without the ball) isn't working correctly. When I turn it on, the red power light, as well as the medium pile buttons flashes. When I first turn it on, the brush rotates for 3 to 5 seconds, then once I start moving the vacuum, it stops and that's when the lights start flashing. I've checked the filters, they are dry and installed correctly. What could be the problem?


I need help repairing my Dyson. I cannot push the buttons down to select Short pile/Medium pile or bare floor. The buttons will not push down at all. It will not allow me to select anything. I have very short pile carpet so it does not pick up that w ... Dyson DC28 Animal Bagless Upright Vacuum

The rotating brush is stopping - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


Two things you can do. 1- Remove the brush as if you were going to change the drive belt for it. Clean the brush as best you can and spray some WD40 on the hard rubber/plastic pieces at both ends of the brush. Rotate the pieces to work the WD40 ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

It stopped sucking @ brush stopped turning - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum


Usually on this vacuum those two problems are not related, but if you got a lot of stuff stuck in the brushroll and in the suction tube at the same time it could happen. Check the belt to make sure it's not broken. If the vacuum is over a year old th ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Brush won't turn even though belt is fine - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum


Hi.\015\012\015\012Ensure drive selector knob is not stuck on park or stop when you lower handle to vacuum if it is pull handle back & turn knob by hand to drive position.\015\012\015\012If you have done all this & sti ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Brush not working - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum


I had the same prob with mine forEVER! I thought the only solution was to return it to Dyson and spend almost $200 for the repair. Just doing the belt reset worked. The brush is now spinning again and I also have suction again! I LOVE my Dyson &l ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0661 seconds