Having problems with your Dyson DC14 Animal Bagless Upright Cyclonic Vacuum ?

I have a Dyson Animal. Roller bar won't turn/belt intact

\015 Makes a horrible noise when "carpet" selection is chosen. Bar is clean and free of any obstacle. Suction seems fine.\015

Answers :

Actually, I'm the poster who said I have the same problem, but it turns out I have the DC07 animal, not the DC14, but perhaps the solution is the same for the DC14 and it doesn't cost anything! I called DYSON and they told me the clutch needed to be reset, so she had me recline the vacuum from its upright position, lay it on it's side, turn the carpet/bare floor dial slowly back and forth between the two settings about 6 times and it apparently reset the clutch and now the cleaner bar spins normally and there's no more loud grinding-type noises. She said if that didn't work, the next step would be to remove the bottom protective panel (secured with the three large plastic screws) and lift the entire cleaner bar (do not remove the belt) out about an inch or so and then reinsert it and reattach the bottom plate. I hope this helps your problem. Good luck.
Repair Help & Product Troubleshooting for Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Dyson Animal. Roller bar won't turn/belt intact


Actually, I'm the poster who said I have the same problem, but it turns out I have the DC07 animal, not the DC14, but perhaps the solution is the same for the DC14 and it doesn't cost anything! I called DYSON and they told me the clutch needed to ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Hi,dyson dc25 overdrive,my brusher's wont go round,i have cleaned the brusher's and filter,loads of suction.the belt is intact and the roller move's feely by hand,could it be the switch


Hi Stephen,I'm sorry to hear you've had difficulty with your DC25 Overdrive. If the brush bar won't rotate, and you've already checked the cleaner head is free of obstructions, it's likely it just needs resetting.You might like to tak ... Vacuums

Dyson dc25 beater bar wont turn - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The Dyson roller ball vacuum I have is making me crazy because the roller bar wont turn. What gives?


Check that you dont have anything blocked in the roller, if all is clear there is a little red button on the side off the roller.\015\012Push this in and this will reset the roller...\015\012If that doesnt work, check that it is switched on with the ... Dyson Ball DC24 Bagless Upright Vacuum

Dyson dc25 roller bar works but no suction - Dyson DC25 Animal Bagless Upright Vacuum


Hi there,I'm sorry to hear you're having difficulties with your DC25. If the machine doesn't seem to be picking up as well as usual, this may be due to a blockage. The filters may also need a wash.The easiest way to locate and remove ... Dyson DC25 Animal Bagless Upright Vacuum

I accidentally sucked up part of a blanket with my DC-17 Animal Dyson and now the roller brush makes a griding noise. Did I ruin the clutch or the roller bar. When I lift up on it slightly it doesn't make the noise only when resistence is applied.


My Dyson started making a loud noise when in "carpet" mode. After reading a ton of forums I thought it was the clutch assembly. Got a new one on eBay for a great price. Somewhat hard to replace, but thanks to this YouTube video, I was able to get it ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Hi my dyson dc07 animal has suction but the brush bar wont turn. If I turn it on there is a horrible noise. The belt is still fine


The belt is probably worn or stretched. When this happens the belt won't turn\015\012the roller brush when it is against the carpet. Here is a link for the\015\012manual and links for the belt ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Roller motor on a DC17 dyson wont turn on


There is a reset button under the cover that houses the on/off switches. remove the handle/wand and look on the back (where the top of the hose sits) for 2 screws (its a torx/star head screw size t10 i believe). remove them and locate 4 small locki ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dyson dc25 roller bar won't turn


... Dyson DC25 All Floors Bagless Upright Vacuum

Dyson Animal DC 28 brush bar removal


Hi there, it's Jack at Dyson.I'm sorry to hear you're having difficulty with your DC28's brush bar. I've attached our video which shows the correct way to remove any obstructions and reset the machine, in case this is useful to you.Th ... Dyson DC28 Animal Bagless Upright Vacuum

Dyson animal beater bar not working - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


Is the belt ok that drives it , is the clutch ok this video will give you instructions how to fix ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Our Dyson upright vaccumms beater bar wont move. the vaccumm will **** up air but the bar underneath wont move. The gears are not working property.


It could be the clutch that's causing the problem or the belt. Bring your vacuum to a local repair shop and have it look at, but it sounds like it could be either one of those problems. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Had my dyson root cyclone for about 4 years now, and in the last year it's had a few problems. About 4 months ago it started to make this awful grinding sound when the roller bar was engaged and I took it to a repair shop and they said it was the roller bar itself. The shop replaced the part and it worked fine for a couple of months and then it started to make the grinding noise again. I tried the clutch reset suggestion (turn it on its side and turn the carpet/bare floor switch slowly back and


Bdepends how much thay charged you for a roller brush because you can buy a good vac for about 100 pounds with a 12 month guarentee so its up to you ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

DC17 Animal Bagless Upright Cyclonic Vacuum: dyson animal wont turn off...


Dyson has switch problems, needs new switch. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

DC17 Animal - loud noise in roller bar


We were able to get in touch with the Dyson support people and they told us this model doesn't have a clutch in the roller bar. The support person helped us walk through looking at the vacuum and it turns out the belt was stripped and they are sendi ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Have a dyson dc07 -roller bar broken. have


It always feels like something must break as it's a really tight fit, but go to www.dysonmedic.com then scroll to the bottom of the page and click on DC07 belt and brushroll replacement guide. You'll find everything you need there. Good luck! ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Beater bar not spinning on my dyson animal DC14. Motor turns on and sounds good. My belt is not broken, and still tight on the bar. It looks like another possible belt or gear box between motor and bar. Can anyone please point me to next step?


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Dyson 17 DC Animal - hit a nylon strap that got stuck in the roller. Removed strap but roller made noise when engaged, now roller not engaging but rolls free when turned manualy.


It could be the belt. Here is the replacement belt you need:Dyson DC17 Belt ... Vacuums

I have a DC14. About a wk ago it was making loud sound and bar stopped turning. i unclogged everything....now the suction works great. However, the bar still wont turn. The belt inside is still intact and isnt loose. Several solutions suggested resetting the "Red" button...i have searched the vacuum over and over. there is NO red or any other color reset button. The bar is set down perfectly in there, the cover plate is installed properly. What other problems could there be? Or do i just need to


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My dyson animal is hard to push on carpet - the beater bar is still operational. When I turn off the beater bar and run the vacuum on hardwood the beater bar stops moving, but it still ''rolls'' on the hardwood - it doesn't pull up like it used to. It also seems to not be picking up as well as it used to, although no blockages are present and the filter is clean.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Beater bar belt needs replacedon a dyson DC14 animal


Remove the glide plate at the bottom of rhe machine. Remove brush and broken belt. Fit new belt and re install brush. Fit glide plate, job done.Its in the instruction book ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Dyson DC17 Animal roll bar makes the vaccum buck


You need to replace the drive belt. You can get one here:Dyson DC17 Belt ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Roller bar belt broke on my dc17 animal. how do i


This belt isn't available at your normal retail stores like Walmart or Home Depot. You can try your local vacuum repair shop, but not all vacuum shops carry Dyson parts. The best bet is online. You can get this belt here at this link and shipping is ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The brush bar wont spin on my dyson dc 25... i


Hi its Darran at Dyson.Simply switch the machine off and stand it upright. Press the brush bar on/off switch once and then turn the machine back on. When you release the machine into the vacuuming position, the brush bar shoul ... Dyson Ball HEPA Upright Bagless Vacuum - Iron/Satin Yellow

Roller doesn't work on my Dyson Animal 14. How do


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0675 seconds