Having problems with your Dyson DC14 Animal Bagless Upright Cyclonic Vacuum ?

Turns off as soon as I turn it on.

\015 Vacuum was working great. Did the living room, hallway, and went to do my sons room. As I was going to my sons room, it came unplugged. I moved the plug to the hallway, and now as soon as I turn it on it turns right back off and smells like something is burning. What could have made it do this?\015

Answers :

Almost certainly you have damaged the flex and it will have to be re-wired. You should never unplug the machine by pulling on the flex, and this why.
Repair Help & Product Troubleshooting for Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Over heating Light Comes on as soon as I try to turn the unit on. I have a Miele S558 Silver Moon vacuum that has only been used once and it shut off and will not come back on. The overheating light comes on as soon as I try to switch speeds on the handle or turn the unit on at the canister, and the vacuum will not run. Do you have any idea what the problem is?

... Miele s558 Silver Moon Vacuum

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.

The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

Turns off as soon as I turn it on.

Almost certainly you have damaged the flex and it will have to be re-wired. You should never unplug the machine by pulling on the flex, and this why. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My hoover spin scrub brushes stopped spinning and i have cleaned intake filter and tried to turn the thing that spins it...when brushes are off the hole turns then as soon as i connect brushes the brushes will not turn what else can i do!!???

... Vacuums

4870 Boss Smartvac. The vacuum tipped over and now the brush control lever will not stay in the carpet position. I can't get the brush to turn unless I push down and hold the lever. As soon as I let up on the lever the brush stops turning. Any ideas. The vacuum is only a month old.

The Boss has a slide lever on the top of the power nozzle with two position choices. One position is "Carpet" and the other is "hard/bare Floor". The power nozzle brush roll is activated when the lever is in the Carpet position, and it is t ... Eureka Smartvac 4870 Bagged Upright Vacuum

I have had a dyson vaccuum cleaner for three months and it does a great job, but the red on/off power switch won't stay on now. As soon as you press it down to turn on, it comes right back up and turns off. What can be done?

Hi its Darran at Dyson.Call our Helpline on 1866MYDYSON and one of our advisors will be able to arrange for this to be reparied. As your machine in only 3 months old, this should be covered by the warranty. Kind regardsD ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The roller will not turn off on our Oreck Halo. As soon as I plug it in, the roller turns on. Any ideas?

Not familiar with the Oreck Halo, but that sounds like a shorted switch. ... Oreck Vacuums

My vacuum is a Kenmore Special Edition with a Power-Mate 12.0 AMPS wand. I ran over the edge of fringed edge of my living room carpet and immediately turned off the vacuum. Although I have removed the fringe pieces from the wand head and I have pushed the overload protector reset button on the wand, the wand brush will not turn. Help- it's the Thanksgiving weekend and guests are coming soon! Thank you.

... Kenmore 25512/ 25513 Progressive Canister Vacuum

Scooba battery light turns red as soon as irobot starts

Do you leave the battery on charge long enough? Try 4-hours up to overnight. If so, then the battery is probably at the end of it's useful life. Getting a new battery depends on cost versus life expectancy of the robot and whether it does the job you ... iRobot Roomba 4210 Bagless Robotic Vacuum

Brushes stop turning as soon as there is resistance

Try this linkhttp://www.vacsite.com/en/bissell-/002V-2032514.html ... Bissell SpotLifter 1716 Bagless Handheld Vacuum

I have a brand new hoover canister s3755 and the beater brush will not turn on the carpet it spins fine as soon as you lift it slightly off of the floor, I can't imagine it is the belt as the mac

It's commonly the belt when they're new. More explained here:http://www.vacuummedic.com/blog/2012/10/09/my-brand-new-vacuum-doesnt-work/Call Hoover and complain, they'll likely send you a new one. The service centers will not ... Vacuums

Why does the belt keep breaking as soon as I turn on the vacuum?

Hi\015\012Have you got the correct belt? If its breaking then the brush end caps or something is clogged. If you can get into the floor head ensure you look at the actual brush roll to see if there is anything is clogged or trapped. Remove all matter ... Eureka 431A Optima Bagless Upright Vacuum

On-off switch My problem is finding a source for an on-off switch for an electrolux vacuum sweeper model 2100. I have replaced the broken toggle and now the sweeper turns on but only as long as the outside button is depressed. It appears that the on-off switch itself is broken as the switch does not ''hold'' when the toggle is activated. It seems to return to it's ''off'' setting as soon as the toggle is released. What ''holds'' the switch in its ''on'' position? Does it depend only on the on-

Hi Hugh. The 2100 has a rocker switch under neath the button. it is probably broken, or the button has a worn detent spring. If you would like, I could send you a switch kit with the rocker, button, and detent spring enclosed for around 20 dollars ... Vacuums

As soon as I turn on my Kenmore upright bagless (twin chamber) vacuum cleaner, it makes a funny noise, then the red light goes on. As far as I can tell, there is no big clog

Have you replaced both filters? remove the canister and turn the unit on. feel at the inlet hole or under where the canister sits. If you have suction there and you installed new filters check in the hose for a clog, shine a flashlight at one end if ... Kenmore 25512/ 25513 Progressive Canister Vacuum

We keep changing belt on tesco vcu007 but it breaks again as soon as we turn it on

I am unfamiliar with this make and model, but assuming it is an upright vacuum cleaner type design, something must be stopping the brush/beater bar from rotating. When it is then switched on, this immeadiately places a huge strain on the belt which ... Vacuums

Hi. I have Dyson dc08 hepq+. Thet problem is its not having suction .I checked inside the pipe and foot , ery thing is fine. And if i take the whole dirtbin out ...machine workes fine. when i put ery thing back ....as soon as i start it , after 2 second machine change its voice...and loos suction. I think its just happen because ...the saftey yellow valve inside the machine turns up because the dirt drum is blocked inside some where. Any suggstion ...what can i do with it. I m tahnkful in avance

Hi its Darran at Dyson.From your description of the problem, it sounds as though the bin inner is missing. To confirm this, if you remove the cyclone and bin from the machine, then separate the 2 pieces as if you were going to empty it, w ... Dyson DC08 Hepa Allergy Bagless Canister Cyclonic Vacuum

My bissell aroma pro had a horrible burning smell then stoped sucking up water. the motor was still working and water was being feed out just not back up. the machine was hot as i had already cleaned 3 rooms in the house. i let it cool down but the burning prob returned as soon as i turned it back on. any help would be great thanks

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum

Canister vacuum keeps turning off, can push buttons on wand handle to restart but shuts off again as soon as you start to move handle

Its sounds like the problem is either the power head wire which when your using it and twisting it left and right, turns it off.. Or it could be in the hose where the connect meets with the unit.Here's a number to call to further assist y ... Miele S548 Bagged Canister Vacuum

I have the yellow altima vac. for a while now I can not get the darn thing to pick up properly. Or should i say keep it up.. The vac does seem to be getting everything picked up but as soon as you turn it off, you have a mess under the vac.. I have checked for clogks and can't seem to find any.. I have removed the hose, Nothing there.. And yep have removed the yellow thing inside the trash cup.. Is there anything else you could suggest??

If it smells hot, then there's a strain on the motor no doubt about it. Check the suction channel behind the sole plate and remove all of the hoses to check for a clog. It could well be that there is a clog inside the machine after the dust channel f ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

My shop vac blows dust as soon as it's turned on and throughout use. I have changed filters, nothing is helping. What part of my vac can not get wet, or is there a better way to clean out the system?

There should be a cover or sock over the filter,this will stop the dust.the paper filter is the part that can not get wet. if you don't have a cover for your filter use an old sock or something simular to a sock. ... Shop Vac 584-04-00 Quiet Canister Wet/Dry Vacuum

Bissell Pro 2X. The brushes spin as soon as I turn it on but only spins for an instant then it quits spinning. The vacuum stays running. the handle is down.

It might be the drive belt slipping if the unit is off then the belt is locked onto the belt and then when the unit is switched on the belt slips and if its loose it doesnt hold the belt to the motor shaft  ... Bissell 9200 Upright Vacuum

Agitator brush It won't spin. I have replaced the belts but they just burn up soon after turning on the machine.

Is the brush turning free on its bearings , Is the end of the motor spindle clean ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

Back filter and its door blows off as soon as I turn it on.

Thats good has good suction i guess there should be a cover on that back filter if you can't find you can tape it down leave air coming out ... Electrolux UltraLux 2000 Bagged Canister Vacuum

I have a Hayden SuperVac 3600, almost 10 years old. The unit still runs, but now when I switch to the power nozzle, it doesn't have power to turn that. I think this happened once before and maybe they replaced a circuit board(?). We took it to a local repairman this time and he says he can fix it temporarily with a new cartridge, but that he won't promise it won't happen again soon.....

The hose has fuseable link inside, generally a 3-7 amp. It is at the wall end underneath the hose cuff. Easy to replace as it crimps in line. If you have a meter you can also test the detachable hose to wall cord for continuity, then check the hose t ... Hayden Industries SuperVac 6000 Central System Vacuum

Put in new bag but as soon as we turn vacuum on motor stops red light comes(bag full)

Make sure the bag is installed properly and the bag door is making contact with the small switch by the bag. ... Electrolux Guardian Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0370 seconds