Having problems with your Dyson DC14 Animal Bagless Upright Cyclonic Vacuum ?

There are no blockages and the belt is intact, but my brush is not turning on my DC14


Answers :

Just remove the screw, pop the brush off, and clean out the ick that's \015\012built up underneath. When you put the brush back on, SNAP it on before \015\012you screw it in, or it will fall right back off. If it still doesn't \015\012turn, call customer support and let them know your module isn't working.\015\012 1-877-855-8593.

your belt is worn and stretched out.contact your local vacuum repair \015\012shop and they should have a spare.tell them the model#

This may have something to do with the brush. The bristles may be worn \015\012down and not touching the floor. Turn your vacuum cleaner upside down \015\012and run the long side of a ruler along the bottom of the vacuum cleaner \015\012head. If the bristles don't touch the ruler, replace the brush. Also, \015\012most brushes have a belt that turns it. Be sure the belt is not broken. \015\012Turn the brush by hand and make sure it turns easily. There may be a \015\012bunch of hair, string, whatever that is binding it up. Last, while \015\012you've got it upside down, turn the vacuum cleaner on and make sure the \015\012brush spins. Stand back when you do this!! It may throw a little rock or\015\012 something at you. Then turn it right side up and listen to see that it \015\012keeps spinning.

Good luck.
Repair Help & Product Troubleshooting for Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

There are no blockages and the belt is intact, but my brush is not turning on my DC14


Just remove the screw, pop the brush off, and clean out the ick that's \015\012built up underneath. When you put the brush back on, SNAP it on before \015\012you screw it in, or it will fall right back off. If it still doesn't \015\012turn, call cust ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Model DC14 beater brush doesn't turn. belt from motor turns but doesn't turn beater brush belt from clutch . Is clutch bad??


You might need to replace both belts. You can get them here:DC14 Replacement Belts ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

The power nozzle works but only on tile. the brush does not turn. the belt is intact. could the motor that turns the belt be broke? is this something i can replace myself or is it better to bring it to be serviced


Depends on you if you feel you could possibly repair it by replacing the electrical motor or you may just have a wire thats nolonger getting continity. enevitably it's your decision if you can repair it you will come off cheaper :) ... Electrolux Guardian Bagged Canister Vacuum

My bissell pro heat carpet cleaner is not working properly...the scrubby bar is not turning... the belt is intact and working and it is turning the knob inside but the brush bar does not turn


How are the bearings? Maybe the motor that drives the belt is burnt out. ... Vacuums

I have a DC14. About a wk ago it was making loud sound and bar stopped turning. i unclogged everything....now the suction works great. However, the bar still wont turn. The belt inside is still intact and isnt loose. Several solutions suggested resetting the "Red" button...i have searched the vacuum over and over. there is NO red or any other color reset button. The bar is set down perfectly in there, the cover plate is installed properly. What other problems could there be? Or do i just need to


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a DC14 with a bad belt to the roller.How do I remove the clutch that operates the belt to turn the roller. I am holding the assembly that houses the clutch and all screws are out, it appears the red knob that engages the drive to operate the roller brush must be removed. Please advise and how. Thanks, John.......[email protected]


You need a special tool to remove the clutch. Contact the Dyson Helpline so that they can refer you to an authorized Dyson dealer in your area who would have such a tool and who can fix it for you. The alternative is to purchase a tool and visit YouT ... Dyson DC14 Bagless Upright Cyclonic Vacuum

Both drive and slave belts are intact and tight on the Bissell ProHeat 2x. The brushes will not turn. When last turned on, there was a loud snap noise and something is broken in the power head drive train. Can we repair this or is there a service center near the Hastings, MI area? We need this fixed ASAP. Thank you.


Sounds likely you should take it in your drive gears might have a problem ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The gear that turns the dual brushes on my Bissell Spot Lifter 1716 seems to be stripped. The belt looks loose as well, but when I take the belt cover and the brush assembly out, the gear that turns the brushes is loose and appears to be stripped on the cogs. When I turn the machine on the belt turns the gear but the brushes just sit there an vibrate. They make an attempt to turn now and then but not much. Need to get a schematic or the parts so I can order the gear if it is available and th


... Bissell 1716 Spot Lifter PowerBrush Bagless Handheld Vacuum

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc


... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.


The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

For some reason, when I tried to put the floor vacuum attachment back on and vacuum the carpet, I realized that the belt was not engaging. the belt is in there and not broken, but it is not turning the beater brush. it is just hanging loose around the brush. When I turn the wheel to engage the brush, it picks the belt up, but when I attach the vacuum to the attachment, the brush is just not turning.


... Kirby Ultimate G Bagged Upright Vacuum

I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn


Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum

My beater bar is not turning so the vaccuum is not picking up. The belt is not broken. The motor is working and I can see the cyclone effect in the canister. I have checked for blockages. I have cleaned the hair and string from the beater bar brushes. What should I do?


You need to replace the belt, it has probably broken. Your actually supposed to change them yearly. Here is a link to\015\012the belt you need and a manual with instrutions: ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Brush won't turn, belts intact - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


Even though the belt is intact it can still be stretched and not turn the brush. You can get replacement belts here:www.vacbelts.com ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

The brush is not working when I turn the power on and the belt appears to be on and intact. How do I fix it?


Where is the reset button on the3760-2 vacuum i cant find it anywhere. my brush wont spin anymore. ... Bissell LiftOff Revolution Pet Vac 37602 Vacuum

Dyson dc07 brush not turning belt is intact? - Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum


DC07s have two drive ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Brush won't turn, belts intact - Vacuums


Even though the belt is intact it can still be stretched and not turn the brush. You can get replacement belts here:www.vacbelts.com ... Vacuums

The belt is not turning the brush on the bottom of my vacuum. I have a DC14 Animal model.


The belt may be worn out. It can also be due to clogging of the brush and side bearings, Check each and be sure the roller turns freely. ... Dyson Vacuums

The brush on my hoover windtunnel will not turn.. I checked the v belt and it seems like its intact .. is it suppose to be inside the groove or just on the grove..it seems loose laying on the grove


Thats why the brushes wont turn,, the belt is slipping put a new belt on then try again,,, ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

DC07 brush does not turn - belt intact - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


Hi there, The problem is likely to be \012a) The selector on the front of your machine is set to hard floors\012b) The ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The vacuum suction still works but the brush wont turn. It still looks like the belt is intact and attached properly.


The problem with Dysons is that the belt breaks and sits in position.If you can turn the brush by hand, with little or no resistance then I would say the belts broken.If in doubt take the cover off and look. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Brush won't turn even though belt is fine - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum


Hi.\015\012\015\012Ensure drive selector knob is not stuck on park or stop when you lower handle to vacuum if it is pull handle back & turn knob by hand to drive position.\015\012\015\012If you have done all this & sti ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

DC14 Dyson vacuum, not vacuuming carpets, beater brush not moving but belt is intact


Possible bad roller or bad clutch assy ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Belt is intact but brush won't turn - Dirt Devil M085850 Featherlite Bagless Upright VacuumVacuum


Even though the belt is intact it can still be stretched or worn and will not turn the brush on the carpet. Here are the belts you need:Dirt D ... Dirt Devil M085850 Featherlite Bagless Upright VacuumVacuum

We have a Hoover upright vacuum cleaner, model Core 7. There is a switch that turns on and off the brush drive. This operates via a cam with a bearing putting pressure on the final drive belt to engage the brush head. My brush head is not turning and with the lever set to engage the drive there is still considerable slack in the final drive belt. There appears to be only a bearing deflecting the belt, should there be a pully or other device mounted on this bearing? There is so much slack a


Yes, there should have been a white plastic sprocket on top of the bearing - in its channel the belt would sit. Unfortunately no parts are available for this unit that can be bought retail - only available by order to dealer repair shops.\012\012\012 ... Hoover Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0785 seconds