Having problems with your Dyson DC14 Animal Bagless Upright Cyclonic Vacuum ?

Just purchased a reconditioned model. Makes a ton of noise and the bottom brush doesn't seem to turn like in my old Oreck. Does that indicate it needs a new belt?


Answers :

Your Dyson does have a belt but its one that cant be replaced it is called a clutch assy. if your roller brush isnt spinning then it could be that you dont have the purple knob on the left hand side if your facing the vacuum to the carpet setting. if you do have it on the carpet setting and its still not spinning then your clutch need to be replaced.
\015\012dyson roller brushes donot rotate as fast as Oreck roller brushes. in fact they are rotate at about half the speed. so keep that in mind.
Repair Help & Product Troubleshooting for Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Just purchased a reconditioned model. Makes a ton of noise and the bottom brush doesn't seem to turn like in my old Oreck. Does that indicate it needs a new belt?


Your Dyson does have a belt but its one that cant be replaced it is called a clutch assy. if your roller brush isnt spinning then it could be that you dont have the purple knob on the left hand side if your facing the vacuum to the carpet setting. if ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

SHARK CORDLESS SWEEPER 3 SPEED CONTROL FLOOR, CARPET, TURBO BATTERY EURO-PRO 8.4V - 1.3 Ah SB617U 3305 BELT Turned on and almost immediately turned off At least four years old - not used all the time - not used in six months Checked belt - seems O.K. Do I need a new battery, if so, where do I get one? Or should I just get a new sweeper? Cost?


... Vacuums

Shark/cordless /sweeper - over four years old. Started - but seemed like it was caught and shut off almost immediately. Not used year around - tried to start after absence. I have removed some hair and perhaps dental floss. Checked belt - it seems O.K. Do I need a new battery or is it just worn out.


Check the brush,is there any dirt got stuck in between brush rolls.If there is then it needs to be cleaned.Your cordless sweeper will automatically shut off if an obstruction is caught in the brush roll. the other thing to checks is dust contai ... Vacuums

I have an 6 month old Dyson 33. Likely need to replace clutch asymbly but still need to change belt's. How do you change those belts without buying another new vacume? Can not remove clutch asym


Here is a video of the dyson clutch change on DC07 witch is the same for DC33 ... Dyson DC-33 MultiFloor Upright Vacuum Cleaner

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the


Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

No suction I have new belts. Everything is clean. No clogs. When I turn it on it smells like rubber , the brush doesnt spin. Everything seems to be free flowing.. Roller brush isnt stuck on the ends. Took off hose to make sure no clogs anywhere. There is not even suction thru the hose with the handle in upright position.


Generally, the problem is that the belt is not running the brushes.  This is caused by one of the following:\015\012\015\012\015\012beater brush is jammed.  This is either an object stuck in the brush or im ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o


Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i


At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum

Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn't seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right....can you help. I am v


I've successfully used a compatible belt - Royal 104425001 .It's still new, but for the time being at least - it works. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

My beater bar on my Kenmore 116.25615506 canister vacuum keeps turning on and off when I vacuum rugs. The suction continues, but the beater bar seems to be shorting or whatever. I checked the belts and they look like new. Any suggestions? The rest of the vacuum works fine!


... Kenmore 25512/ 25513 Progressive Canister Vacuum

Have a Centralux Aerus about 5 years old. Don't see a model number. There is suction but beater brush quit working. Was using for a few minutes, shut it off for a few minutes, turned it back on and suction only. Tried the reset button also. Tried the sidekick attachment and it works fine. There was no smell like something was hot. Belt is fine. Are there any fuses or anything else to try? This vacuum cleaner has not really been used that much, it is hard to believe the motor would need replaced


There probably is a loose wire in the handle near the switch or a wire off near the swivel elbow near the vac power head. With the right fastener tool to remove some screws you can fix it yourself ... Electrolux Centralux Vacuum

The gear that turns the dual brushes on my Bissell Spot Lifter 1716 seems to be stripped. The belt looks loose as well, but when I take the belt cover and the brush assembly out, the gear that turns the brushes is loose and appears to be stripped on the cogs. When I turn the machine on the belt turns the gear but the brushes just sit there an vibrate. They make an attempt to turn now and then but not much. Need to get a schematic or the parts so I can order the gear if it is available and th


... Bissell 1716 Spot Lifter PowerBrush Bagless Handheld Vacuum

I replaced the belt in our Eureka Boss Smart Vac, it still seems loose, it uses a type R belt. The beater belt still doesn't seem to turn properly and seems that it doesn't pick up very well when I use it on my berber carpet. We have 2 dogs and I like to use it frequently. I have changed the bags and belt......


Check to see that the beater brush is not frozen up. Pull the brush and clean it, spraying some WD40 on each end piece that holds the brush in place.\015\012Also be sure the belt is properly installed so that the brush turns in the correct direction ... Eureka Vacuums

Hoover WindTunnel, month-old belt, now too large to turn brush


I suspect you have been bitten by the Chinese bug.\015\012\015\012A very large percentage of replacement parts for all manner of appliances and vehicles are now being conterfeited in China who we should know by now has no respect for the intell ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old


Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Brush Roller Wondering if I need a new brush as well as a belt. The Roller seems to have trouble spinning when it makes contact with the carpet no matter how the height is set. Everything else seems to work fine. Do I need a new roller to fix this problem?


The bearings can go bad in the brushroll. It may need replaced, even if the brushes aren't worn. Helpful link....\015\012\015\012 ... Kirby G6 Bagged Upright Vacuum

The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t


The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum

How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a


The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover windtunnel t series belt is loose- roller brush doesnt turn. Its brand new belt is slipping. we bough new belts and putthem on same problem. Can not find solutio in manual. Is the belt supposed to go around the "metal pulley". I know it goes around the little metal motor thing, then thru the guide and around the brush. What is the metal pulley??? Is is the larger round silver thing between the guide and roller?


I also have a loose belt and have bought additional belts but have the same problem. I put the it around the metal rotor and around the brush roller a shown by he Hoover video, and it is loose. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

I have a Hoover Windtunnel U 6439-900. The agitator brush will not turn. I installed 2 new belts, # 38528034, and # 38528-035 There is so much slack in belt # 3852034 (brush drive) that it cannot grip the brush. There does not seem to be any adjustment to take up the slack. I've put in new belts twice now & cannot get brush to rotate or tighten the belt to the brush.


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

The brush roller stops turning and I can smell the belt burning, then it will catch and start working normal. I looked under the plate to check the belts and they looked okay and no hang ups of string or anything. The only thing that seemed weird was that the smaller belt that actually attaches and turns the roller is a bit loose. The larger belt is tight but looks like its the one that is burning and causing the smell.


Better to replace both belts the smaller one is stretched out thats whyits slipping ,be sure to clean the old rubber off the motor shaft before replacing the belts.it will cause the new belts to run unevevly and go bad before their time ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Got nEw bElts for mach7 anD thE v bElt Wont turn it seems slack


... Vacuums

Hi, I have a Dyson DC04, (silver/lime) making ear popping screams! Does not happen all the time, and more noticeable when it is pulled back.The suctions not a problem and no funny smells or strange noises from the motor. Ive taken the base plate off and the belt and brush bar seem fine, but when I turn the belt, it seems to be the motor spindle thats squeaking, almost as if it need oiling, any help please


... Vacuums

Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n


From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums

I bought new belts to replace the old ones (one had broken and the water would not feed) My cousin took it apart and now I need to put the new belts on and get it back together - do you have instructions or a diagram?


There are different variations with Bissell. They have the ProHeat series and a Power Turbo series. Below is a link with instructions and diagrams for the Belt Access Door. If this doesn't solve your problem or isn't the correct model, please post ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1105 seconds