Having problems with your Dyson DC14 Animal Bagless Upright Cyclonic Vacuum ?
Suction weak, vacuum seal spring is releases
\015 Vaccuum spring seal is opening and release suction power\015
I would recommend checking the dyson vacuum brushroll first. If there is any hair or thread wrapped around it you are going to want to cut all of that free that way your brushroll can spin freely. I would also recommend checking the filter and washing or replacing that. On the DC 14 that is going to be on the top of the dust canister as well as under the canister if you lift it off of the unit.
Dyson vacuum repair Highlands Ranch
Dyson vacuum repair Highlands Ranch
Repair Help & Product Troubleshooting for Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Suction weak, vacuum seal spring is releases
I would recommend checking the dyson vacuum brushroll first. If there is any hair or thread wrapped around it you are going to want to cut all of that free ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
I am replacing a foot pedal on an upright Sharp vacuum cleaner-EC-TU2607. I have the broken foot pedal removed from vacuum cleaner proper but it is the removal of the broken pedal from its spring load that has me puzzled. I applied some pulling effort on the pin that holds the spring in place but there doesn't seem to be any give. Is that the correct approach or is there something else that one should be doing first to release some of the resistance by the pin or spring? Thanks!
... Sharp Twin Energy EC-TU2607 Vacuum
My A 2045 Karcher vacuum's suction is really weak and the motor seems to be working VERY hard. The motor sounds like it used to when the vacuum fell over and went into overdrive! Now it's in overdrive all the time and the suction is minimal. Nothing is blocked and the filter is clean and dry. What do I need to do?
... Karcher K DS 5500 Vacuum
Low suction Have a Powr-Flite PF 18, suction is good at motor, but low at where hose comes out of top of vacuum. Could new lid seals help the problem? Where can I get new seals for this model. Also my zip is 98801 and my shop is not listed, could you add it please? Sew Creative 1139 N. Princeton Wenatchee, Wa 98801 509-663-5516 Thanks, Lauren-Sew Creative
Replacing the motor cover solved the problem, it must have been warped and was letting suction out thru it. ... Vacuums
Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would "heave" (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won't turn. Any suggestio
Carpet brush won't turn when vac on ... Euro-Pro NV31 Infinity Vacuum
Poor Suction Heya! So I just picked up a used Dyson, but when I vacuum with it, the suction is pretty weak and it spits all kinds of stuff out the back and into my feet. When I pull the hose I have good suction, but in regular mode it hardly picks up anything. The brushes are spinning, and it eventually will clean an area if I go over it again and again. Maybe a clog somewhere? Please tell me that Dysons have better suction than my $50 Dirt Devil! Thanks!
I recently bought a second hand Dyson DC07. Its suction was poor. I removed all the un-clipable pipe bits and to remove any blockage but it all looked clear. The Final Sponge and hepper filter did have a lot of dust in it and the rotating brush was f ... Dyson DC07 Bagless Upright Cyclonic Vacuum
My Hoover vacuum is not vacuuming the carpets or floors. When I release the tube to use the smaller end the suction works perfect. So i believe the problem is in the rods on the floor or in the part that vacuums the floor! Can you tell me how to fix it , or where can I take it to get it fixed? thanks
Ive just had the exact same problem. In the very back lower portion of the vacuum You will need to take it apart. I guarantee there is a clog. You might also check your belts to make sure they are still on track. ... Hoover Vacuums
Electrolux Bagless Canister Vacuum w/Self-CleanHEPA Filter - weak suction
Unfortunately alot of people buy this model because of the electrolux name, but it is actually made by eureeka. Aerus-Electrolux is the manufacturer of the high quality machines of our parents day. ... Electrolux EL7055A Bagless Canister Vacuum
No suction the suction on the vacuum is very weak. What should i do?
Check the hose for clog, take it off if you can, drop something thru it to see if it comes out the other side. Check the dirt inlet by the brush roll to see if it is clear or clogged. Filters could be bad also. Is the brush turning under load ok? ... Hoover U8311900 WindTunnel 2 Vacuum
My new vac master pro200/260 does not vacuum, the fan is on but there is no suction, and the machine stops at 2 without suction or seal and then shows error.
... ARY Vacmaster Vacuums
How to wind cord onto spring loaded retractable cord reel for a Kenmore canister vacuum. There is a metal 'U' shaped, spring loaded, piece that fits over the outer aspect of the wheel. If cord needs to get wound on under this metal band I can't figure it out and the band is like factory sealed onto the wheel. Also. I don't know which direction to feed the cord onto the wheel
What is the exact model # please?Thanks!! ... Kenmore Vacuums
My new Kenmoore Powermate 116 canister has poor suction. I have no pets and light dust. Its not picking up small particles on the wood floor with the floor attachment. When I put my hand to the suction it feels weak. Cleared hose and changed bag. Using again, same issues. This should not be happening with a new vacuum. Is it a bad design in the elbow joint of the hose? I want to return this!!!!
First of all disassemble the handle and hose as much as possible and examine the inside. Make sure there is not any significant debris lodged in the hose somewhere like a plastic bag or something.\015\012\015\012Also check at the top of t ... Kenmore 23912 Progressive PowerMate Bagged Canister Vacuum
My vacuum has gotten clogged by human hair on the spindle. I removed the spindle and the hair and put the spindle back into the vacuum but now the suction is very weak
... Dyson Ball DC24 Bagless Upright Vacuum
Weak suction in my vacuum - Kenmore Vacuums
Take it apart and look for blocked filters, blockages in the pipes. ... Kenmore Vacuums
My vacuum tools have very weak suction. - Bissell 3576 CleanView II Bagless Upright Vacuum
There is a foam ring filter in the bottom of the canister that collects the dirt. It screws off of the bottom on the canister. Take outside and shake it out. It fixed our suction problem. ... Bissell 3576 CleanView II Bagless Upright Vacuum
No suction to seal bag - FoodSaver Vac 800 Vacuum-Sealing Kit, White
Is a hose unplugged? Unplug the devise and see if you can find anything that looks like it's not connected OR it has a hole in the hose. ... FoodSaver Vac 800 Vacuum-Sealing Kit, White
Weak suction on rainbow se vacuum
\015\012\015\012With years of use, you will collect a layer of "micro dust" on the impeller (the fan part) which reduces the efficiency. A toothbrush and some mild cleaner with gently scrubbing will restore it's power. \015\012\015\012T ... Rainbow 75th Anniversary Canister Vacuum
What is causing weak suction on my new Dyson DC24 animal vacuumed?
... Dyson DC24 Animal Bagless Upright Vacuum
How do I replace the handle release lever spring on a Eureka Pet Pal vacuum?
Dyson DC07: When I first got this vacuum, it was so powerful that it lifted my area rugs off the floor. It is so weak it barely works. I have removed and cleaned the filter, but I can?t seem to improve the suction. What am I doing wrong? How do I fix it?
Hello,\015\012\015\012If your vacuum runs but still leaves dirt behind, the culprit could be the drive belt or an obstruction. If the agitator brush slips or won't turn, the belt is bad and needs to be replaced. If suction is weak when yo ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Hello! The suction in my Dyson animal is very poor. I discovered small holes in the internal hose, but even after a quick duct tape fix, still having issues...sounds like the seal from the canister to the vacuum is leaking air. I know I need a major repair but my mother in law is coming tonight! Any suggestions? ~Lisa
Or you can do this for free:\015\012\015\012http://www.ehow.com/how_5870417_modify-dyson-prefilter-suction.html ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Suction is suddenly very weak on fully-charged Shark Euro-Pro SV736CR hand-held vacuum. Inserted new bag, so that's not the problem.
... Euro-Pro SV736 Bagless Handheld Cyclonic Vacuum
Hello, My shop vac has weak suction - Shop Vac 584-06-00 Canister Wet/Dry Vacuum
... Shop Vac 584-06-00 Canister Wet/Dry Vacuum
Very weak suction despite clean filter etc - Dyson Stowaway DC23 Bagless Canister Cyclonic Vacuum
... Dyson Stowaway DC23 Bagless Canister Cyclonic Vacuum
I have a canister vacuum. I replaced the bag and now can otn get a good suction. Could it be the rubber seal near the bag?
The case that encloses the bag may not have been closed properly, or a part of the bag got caught in the seal of the case. Take the bag out and reinstall. Hope this helps! ... Vacuums