Having problems with your Dyson DC14 Animal Bagless Upright Cyclonic Vacuum ?

How do i change the belt from the clutch to the motor?

Answers :

This video will give and show you full instructions
Repair Help & Product Troubleshooting for Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do i change the belt from the clutch to the motor?

This video will give and show you full instructions ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have an 6 month old Dyson 33. Likely need to replace clutch asymbly but still need to change belt's. How do you change those belts without buying another new vacume? Can not remove clutch asym

Here is a video of the dyson clutch change on DC07 witch is the same for DC33 ... Dyson DC-33 MultiFloor Upright Vacuum Cleaner

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?

Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Model DC14 beater brush doesn't turn. belt from motor turns but doesn't turn beater brush belt from clutch . Is clutch bad??

You might need to replace both belts. You can get them here:DC14 Replacement Belts ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Belt replacement appears to have 2 belts, 1 is on and 1 is missing, the belt that is driven by the motor is missing, how do I remove the clutch housing where the belt goes?

Hi.\015\012\015\012You are correct there are 2 belts.\015\012They can be tricky to replace most shops will state they cant be replaced & you require new clutch.\015\012So try this site ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Changing fan I changed the broken fan in my eureka 1934A. Put the cover back on and reattached the belt and when I went to start it, it wouldn't work. I took the cover back off to see what was going on and it looked like the motor was running in reverse of what it had been. Is this possible?

My solution is one that only works if the vacuum is a spare... To get mad at it and throw it in the garbage... \015\012\015\012My thought though on what the problem actually was... Seeing as where the vacuum came from and what the problem ... Eureka 1934 Bagged Upright Vacuum

How do you remove clutch out of DC14 ro replace belt from motor to clutch

First remove bottom plate then remove the roller yea I know its a pain the front nozzle will come off if you pop it up with a screwdriver pull the suction hose it will come off. the knob is the worst there are two points were it clips on firmly pry t ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

How do I change the belt on my Hoover Elite Dual Purpose Vacuum cleaner? The belt part # is 38528-027. Where is the motor pulley?

The hoover belt number you listed (38528027) has been changed by Hoover to 38528040. Below I have listed a link to the manual that has instructions and a link to the belt you need. Hope this helps! ... Hoover Elite U5061-900 Bagged Upright Vacuum

How to change a clutch belt

Click the link below for instruction videohttp://www.youtube.com/watch?v=7_CtaFcc5HU ... Vacuums

My belt has snaped on my dyson dc04 that has a clutch how do i change it

Remove the roller brush cover plate that is on the bottom and you will be able to access the belts. Here are the belts you need:Dyson DC04 B ... Vacuums

Dyson dc04 I have just stripped machine and found the drive belt from the motor snapped. How do I remove the clutch assembly from the housing? I have removed the 2 screws but the yellow knobs are still in place.

Hi,\015\012\015\012Go to this site for manuals to help with your Dc14.\015\012http://dysonmanuals.llc.nu/\015\012\015\012Chris. ... Vacuums

One day I was vacuuming and it sounded like something went up inside somewhere and the motor, I assume,..... is frozen ..all it does is hum when I turn it on! I have changed the belt, filter and checked and cleaned all hoses... what could this be? THANK YOU, Gail

It's likely something got into the fan, is stuck there, is preventing the fan from turning, and so prevents the motor running. There's a good possibility the motor burned out because of this. If there's a strong smell of burning metal, this is prob ... Hoover Elite Rewind Bagless Upright VacuumVacuum

Dc25 dyson upright vaccum cleaner. Brush inoperative. have changed on-off switch and the reset switch. the belt is intact and iam left with possible bad brush rotator motor???

... Dyson DC25 Vacuum

How to change a drive belt the brushes are not turning but the motor works

OK, here goes... NOTE - any use of the words LEFT and RIGHT assume that you are looking from the REAR of the machine. NOTE ALSO - the machine has two toothed belts, it makes sense to change both while you're at it. Inciden ... Sebo X4 Bagged Upright Vacuum

Th end of the shaft that come from the motor is worn out, and won't hold the belt well. How do I change it?

Hello,\015\012\015\012Thanks for the clarification. I have never seen this problem previously in a Kirby. I wonder if the belt keeps sliding off because it's been stretched out? After about 1-2 years, the belts on the Kirby will str ... Kirby G5 Bagged Upright Vacuum

I have a Bissell PROheat 2X shampoo carpet cleaner and the brushes stop working. i have changed the motor and checked the belts. everything is fine. any ideas?

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

There is a high pitches nosie coming from my dyson. It mainly happens when the flooring type changes whilst hoovering. Everything else is ok. It sounds to me like the drive belt for the brush bar or could it be the clutch. Hoover is over 10yrs old but is in good order and well looked after, this is really the first thing that has ever gone wrong with it.

... Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum

What causes these things to become unbearably loud? We've cleaned evey filter on the machine, pulled every speck of hair and lint off the brushes, changed the belt, no clogs anywhere. I've totally (and I mean totally, down to the brushes on the motor!) torn this thing down and put it back together with no difference. Also have a Eureka bagless, and after minimal use, and almost anal retentive maintance, it does the same thing,to stinkin loud. Wish one would **** up the other to save a trip to th

A clog in the hose or dirt inlet by the brush roll will cause the motor to sound loud. But so will a bad motor bearing, or motor fan, in which case you would have to replace the motor. ... Bissell Vacuums

I need to remove the motor in my ricar 4812 (to change the axle) Where can i find something on that? I have 4 screws out- but it seems to be held into the body where the shaft goes out to the belt. Just missing something dumb.

... Riccar 4812 Vacuum

How do I change the belt on the motor? - Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hi. This is easily done. Flip the vacuum over, beater bar up. With the machine unplugged, locate the screws or tabs that hold the base plate on, surrounding the beater bar. Remove the plate. The beater bar is held in place by fitting into socket ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

My Dyson dc-07 makes a loud grinding noise only on the carpet setting.The belt seems to be fine,and the brush spins normally.Do I have a potential clutch or motor problem?

... Dyson DC07 Bagless Upright Cyclonic Vacuum

We have a Bissell Clearview Revolution #3595 and the motor when turned on Screeches, loudly, it does ****, just incredibly noisy we have already changed the belt

Sounds like a bad motor, part # \015\012\015\012\015\012\015\0122032211It would cost around $60 for a new one. Did you check the brush roll to see if it is making alot of noise, if it is then replace it. ... Vacuums

How do you get the knob off to take clutch out to change belt?

... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Motor making high pitched noise.....changed belt already..? Need help.

... Eureka Whirlwind 4388 Bagless Upright Cyclonic Vacuum

I need to change belts on my Dyson14 upright w/ clutch

Click the link below for video how to change clutch and belt on your DC14http://www.youtube.com/watch?v=7_CtaFcc5HU ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0519 seconds