Having problems with your Dyson DC14 Animal Bagless Upright Cyclonic Vacuum ?

Loose wire Been tugged causing loose wire at handle end of flex

Answers :

Needs new cable 20.00 for replacement 0800 294 4692
Repair Help & Product Troubleshooting for Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Loose wire Been tugged causing loose wire at handle end of flex

Needs new cable 20.00 for replacement 0800 294 4692 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Spare wire? My SEBO X4 flex had to have the fex shortened because the cable sheathing had come out of the internal gripper and there was a couple of inches of two strand wire hanging out the cable entry point before the insulation sheathing started. No problem doing this but on the live switch terminal there was a piggy back spade connector. The second wire from this went down inside the handle and just ended with a bare terminal hanging in space. It hadn't come off anything, there wasn't anyth

Greetings from GoVacuum.com,I took a picture of the Sebo X4 wiring in the handle of the machine for you. This is a brand new machine taken out of the box, this is how the wiring should look. You'll see that there are 5 total wires here. ... Sebo Automatic X1 Bagged Upright Vacuum

DC07 DYSON REPLACEMENT HOSE. HOW DO YOU REMOVE IT FROM THE HANDLE. I have a kenmore whispertone 8540 canister vaccum. The electrical wires (3) to power the beater are embedded in the hose, in a spiral fashion. The yokes that hold the hose on both ends (and attach to the beater on one end and the unit on the other) have no screws or pressure latches; i don't want to use brute force as i may damage the attachment device inside the yoke. If someone can tell me the trick to get these yokes off each

Should be a pry off dot on the underside revealing a screw ... Vacuums

Hoover wiring the blue wire that is in the lead that runs from the hoover to the plug that goes in the wall has come loose at the hoover end and has come out of the actual hoover. i've unscrewed it but am unsure as to where the blue lead (bare copper) needs to be screwed... if you see what i mean?!!

Hello lukeplayer,\015\012Based on your description, ( first disconnect the plug from the wall recptacle).You will need to open up the Hoover Vacuum Body to gaion access to the internal wiring. In order to better assist you, please provide me wi ... Hoover Vacuums

We have had the power wires that run through the swivel elbow at the end of the main handle extensions and the power head break after being repaired two times. The new swivel elbow and wiring connection was installed bya local, non-electrolux vacuum shop each time. What is the trick?

Have them replace at the Aerus Electrolux shop. Aerus uses a higher grade plastic (Lexan, read about it on the net) which should last the life of the the power nozzle and wands. The part and labor will have a 1 year warranty. ... Electrolux Epic 6500 Vacuum

I have a new Bissell power groom pet, 67E2 that I purchased a while back. It has never been used. I am trying to use the pet tool adapter. Do I disconnect the flex hose (handle end) from the telescoping wand to use the pet tool adapter? And, if so, how do I disconnect them?

... Bissell Powergroom Pet Vacuum

Inside the vacuum handle of my Wertheim 5030 1800 there is a white earth wire that has a sprung loaded clip on the end. Does anyone know how to put this back into the right position as I opened it up to clean some wet plaster from inside and it became misplaced.

... Vacuums

How to attach pet tool adapter? Do I disconnect the flex hose (handle end)? If so, how?

Hi Sarah! The flex hose doesn't need to be removed to use the pet tool adapter. Just attach the pet tool to hose and begin vacuuming. ... Bissell Powergroom Pet Vacuum

Mrs Cleaner flex has pulled out how do I replace Electric supply wire to switch on handle has broken at switch. How do you remove switch to repair? tonysimmons

Hi\015\012\015\012\015\012\015\012\015\012\015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.

... Hoover U6485900 Bagged Upright Vacuum

Sock stuck in hose midway. Unable to getit out with wire or brrom handle. Is there a way to take hose apart at either end.

If the sock is midway, taking either or both ends apart won't help. Take it to a vacuum repair shop and ask them to try to unplug it. You may need to buy a new hose. ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

Wire is loose in the handle of my oreck xl clasic i have to hold it to make the vacuum work what can i do

... Oreck XL2000 Bagged Upright Vacuum

E series power head handle, internal wire came lose

Here is a pix.\015\012\015\012 ... Rainbow E series Canister Wet/Dry Vacuum

Dyson DC04 i have a loose wire where the cable enters the cleaner how do i open the part where the on/off button is. A wire is loose probably but I cannot get to the interior to check its status. How can I take it apart? the plug is sealed but could it be a loose wire in there?

You have to remove the yellow switch but to do this there is a small hole at the side of the switch nearest to the machine you have to push something in this which will push the clip that is holding the switch if you can do this there is a screw behi ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Have Dyson DC 14. When tilt to vacuum, the handle and coiled hose comes away from the unit. The problem started when the little purple ridged curved part on front of vacuum cleaner right below handle came loose and a spring fell out from somewhere--don't know where. I pushed on the purple ridge part and it snapped back on. Now, can't get it loose again, don't know where the spring goes, and handle still comes loose from vacuum.

I'm not positive whether or not this is the wand handle because there are several versions of the DC14. However the device the locks and unlocks the wand in place is pretty similar between all the versions.The first picture is the wand re ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Power head handle wiring

That wire goes just above where the trigger is, take the trigger out and there is a slot that the end goes into. ... Rainbow E series Canister Wet/Dry Vacuum

Loose wire ive got a loose wire inside my vax cyclonic 1700w and ive stripped it down but cant see anything and its still not working but it was working when i moved the wire from side to side. Please help

Sounds to me like you have a open wire. There is a break in the wire inside to the insulation and as you move it, it gains and loses connection. You can test it with a continuity tester as you move the wire or just replace it to see if that solves th ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

The handle was getting hot and we opened the handle and the wires were melted around the switch. I need a part number for it. All I have seen are 2 wire and this is a 3 wire. Thank you.

Had exactly the same problem with my upright Eureka Model 5893\015\012bagless. Eventually, the handle would get hot, and finally it just\015\012quit. When handle was disassembled, the wires were melted and it was\015\012toast. Ordered a switch aft ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

Wire came loose, can't figure out where it belongs

Maybe one of the wires that leads to the power head? ... Lindhaus HF6-12 Canister Vacuum

E series power head handle, internal wire came lose

Think it comes off of the hose. Maybe it broke off. ... Rainbow E series Canister Wet/Dry Vacuum

Where can I purchase a replacement wire for the handle of my aerus centralux hose? It's the black wire that runs from the switch in the handle and attaches to the pins in the wands.

Any Aerus Electrolux store should have them in stock.\015\012You can find the one nearest you by following the directions on the below site:\015\012\015\012 ... Electrolux Centralux Vacuum

The handle for my Eureka 5993 AVZ was getting very hot when used. Finally, the wires around the switch melted and now the vacuum will not work. What is wrong? Is the switch bad? The wires only melted in the immediate vicinity of the three-prong switch. Nothing else appears to be wrong; the vacuum worked fine when it was running - except for the handle getting hot. Thank you!

Try cleaning all...\015\012if have sam paoblem need replaced main motor.... ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

Wiring diagram for Model #11635922500 - KENMORE Upright vac I took the cover off of the vacuum to repair the power cord and must have pulled a wire out of its wire nut by the sweeper bar. If I had a diagram it would be no problem to replace. The bad has four short gray wires coming out of it. It is one of the gray wires that has come loose.

... Kenmore Vacuums

Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?

Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Confusion and embarrasement have caused me to appeal for expert advice. I need to add a second flourescent light fitting in the loft. I recently added one from the existing wiring circuit via junction box and pull chord switch and it works fine. I have wired in the second light and now neither of them work. I have replaced the starter (as I had a faulty one in the first light. But i annot get them to work. I have installed a second junction box for the second light and wired all like terminals

... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0407 seconds