Having problems with your Dyson DC14 Animal Bagless Upright Cyclonic Vacuum ?

Brushes only engage after pushing way past the carpet selection.

\015 I own a Dyson DC14 Animal, and while carrying the vacuum the hose fell out and the vacuum dropped on the floor. Now when I vacuum the brushes only engage when I push the carpet selector way past the carpet selection. Is there anything I can do to fix this, change parts, etc?\015

Answers :

I have the EXACT same problem. Did you ever get it fixed? What did you do?
Repair Help & Product Troubleshooting for Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Brushes only engage after pushing way past the carpet selection.

I have the EXACT same problem. Did you ever get it fixed? What did you do? ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Dc07 problem I have a dc07 cyclonic vaccum and like this model,however, for some reason,it has been very dificult to push and pull for the past month or so. i have completely cleaned the brush assembly,cleared any obstructions in the hoses,and, cleaned the filter.I also checked the belt tension,wich i thought was fine but to no avail.Be advised that the brush assembly is spinning and suction is excellent. It just feels like the brush drags along the carpeting. this is a great vacuum cleaner and

The dyson uses two belts, one from the motor to a clutch and then from the clutch to the brush roller, the belts that they use are not much better then any other belt ( those you should change yearly ) but you cant just change the belts you have to c ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a brand new DC 24 (orange ball) Dyson. The brush is not turning and it is extremely hard to push on carpet. Something must not be engaged. What should I do?

... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Necchi 522, an early mechanical stretch stitch machine. The timing and stitching are great, but over the past few projects I have noticed a balky tendency when I press the knee bar. After my last project the motor almost won't engage. Sometimes there is no sound, and sometimes there is a weak whirring, but no action until I push the hand wheel. I have a feeling that it is either the v belt or that the motor needs new brushes. Are either of these ideas likely, and if so, are they self

Hi,It sounds like the machine is having to work too hard. Have you cleaned and oiled your machine lately? Over time oil will harden and lint and dust will build up on the working parts in the machine causing it to drag and eventually stop ... Vacuums

I have a Bissell Pro Heat 2X carpet cleaner and the brushes spin, then stop. I turn it off and when I re-start, the brushes do not spin until I push foreward. The it spins and stops again. Both belts are tight. The brushes spin if held above the carpet, but upon contact with carpet it stops. Same thing on a hard surface.

The reason for the brushes to stop when it is above any surface is there is a switch in the handle that stops the brushes so it dont burn your motor up it may have a faulty switch. ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

I have a Dyson all-floor model (not the ball). I recently replaced my carpet to a Frieze. Since replacing the carpet, the Dyson is extremely hard to push. It almost forms a "seal" with the carpet. Seems to work fine on Berber carpet and laminate floor. My husband has checked to make sure the brushes are working, hoses are not clogged and belts are OK. I've had it for about a year. It is virutally impossible to push on the new carpet. Any ideas?

Have you adjusted the brush control system. If you look at the link below page 6 will tell you how to adjust. If this is not you vacuum please give the model # of the one you have so I can help you more.\015\012\015\012 ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

For some reason, when I tried to put the floor vacuum attachment back on and vacuum the carpet, I realized that the belt was not engaging. the belt is in there and not broken, but it is not turning the beater brush. it is just hanging loose around the brush. When I turn the wheel to engage the brush, it picks the belt up, but when I attach the vacuum to the attachment, the brush is just not turning.

... Kirby Ultimate G Bagged Upright Vacuum

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.

... Hoover U6485900 Bagged Upright Vacuum

When I push my vacuum with the rotary brush on carpet the rotary brush head shakes. It's fine when I pull it back. I just can't push it.

It may be time to replace the belt on the unit. sometimes when the belt slips (not broken yet) it will give you the same effect. It will also sound a little sluggish too. replace the belt and you should be ok for 1 year. if your using the unit more t ... Rainbow E series Canister Wet/Dry Vacuum

Hoover windtunnel Not sure of model number- but brush roller clamps down on carpet being vacuumed and stops spinning regardless of which of the 3 height selections is selected. Can make it work by leveraging the handle down (or back towards me) to keep the cleaning head a little off of the carpet-any suggestions or ideas?

Would suggest the drive belt is stretched and thus is slipping when contact is made with the carpet. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My Kenmore 35922 works well on floors, but it recently became very difficult to push on carpet. The brush spins and a local vacuum repair guy wouldn't solve my problem since the vacuum worked fine on his very flat, commercial carpet. What can I do to get my easy to push vacuum back?

Hi dalee196,There are three common reasons why vacuum cleaners are getting hard to push.1. Base is dirty - The base needs to be clean from dirt and tar.2. Height is too low - You might want to consider adjusting th ... Vacuums

My Dyson DC 14 is making the horrible "ratcheting"sound only when the brush is engaged on the carpet setting. I have cleaned the brush, so there are no obstructions, the canister is empty and properly on the unit. I checked to make sure all of the "traps" and hoses are clear of obstructions, the belt is on the brush securely and moves freely, the brush itself spins freely, but there is still the "ratcheting" noise. Any other suggestions?

Our DC33 was making the same ratcheting sound immediately upon placing the cleaner/brush head on the carpet. We carefully pulled the beater/brush bar out of the vacuum. Once removed, we pulled the black plastic end off of the center rod. We discovere ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I don't feel that the vac is close enough to the carpet anymore .. it's almost like I have to push the head down so it reached the carpet to roll the brush through it ... I've tried a friends vac and it shows nicely that you've just vacuumed the carpet .. heavy traffic areas are not getting pulled back up .. I have the short shag type carpet .. Thanks

Consider disassembling and cleaning your unit. Sometimes dirt and grit will build up, and when wiped away allow the moving parts to function better. Dysons are made to be broken down by the homeowner. A manual can be obtained here: http://www.manual ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Hoover steamvac Spinscrub F7222-900 brushes do not engage. Brushes will spin when unit is laid down and the brushes are pushed upward, forcing the male brush linkage into the female receptacle , but when the unit is stood up it disengages. Turning the switch on and off does not make a difference.

That's the way it's supposed to work. ... Vacuums

On our new carpet (which is not that thick but thicker than the old) I can't set the carpet thickness high enough. The suction really grabs the carpet and bogs down my self-propelled wind-tunnel Hoover. I then have to push down on the handle to tilt the front up. The thickness setting is as high as it will go. Is there some way that I can further adjust this. The machine is about eight years old.

I can help you out only if you will let me know the front width of the machine. Alongwith the height which you wan't to give raise. KIndly give the width and elevation in cms. ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Its like the roller brush won't lower and it doesn't "engage" anymore. I posted this but input the wrong vacuum model ....not sure if that matters? I can vacuum and you still see footprints on the carpet. I have suction, just no brush action, yet the brush spins....

Sorry about that, I guess I have to post this as a solution in order for the pictures to display. Here's the entire solution on a similar problem that I've answered previously. Please let me know if you need help further diagnosing the machine, I ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My vacuum's rug brush will not spin. the belts are fine and in place, but when i engage the carpet brush nothing happens. i looked under the bottom and there are no obstructions preventing the brush from opporating/

Have your clutch checked out by a local vacuum repair shop. That's a common problem with dyson brush rollers ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Hoover windtunnel U6425-900 the brush roll is not turning. Both belts are in good shape, I cleaned the brush roll and it is free of debris, the setting is on carpet and the brush roll still will not turn. There is a "burning rubber" smell when you attempt to push the vaacum forward a few times. The small belt does not seem to be pulling properly but appears to be in good shape.

... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a Dyson DC17 that has started making a loud noise when on carpet when the brush is engaged but not on hard wood when the brush is not turning. I have remove all the material (hair,lint, etc.) wrapped around the brush itself, but it is still making the noise

You need to replace the belt. Here is the belt you need and a manual you can view which has instructions:\015\012\015\012Dyson DC17 Belt and Manual ... Dyson DC07 Bagless Upright Cyclonic Vacuum

4870 Boss Smartvac. The vacuum tipped over and now the brush control lever will not stay in the carpet position. I can't get the brush to turn unless I push down and hold the lever. As soon as I let up on the lever the brush stops turning. Any ideas. The vacuum is only a month old.

The Boss has a slide lever on the top of the power nozzle with two position choices. One position is "Carpet" and the other is "hard/bare Floor". The power nozzle brush roll is activated when the lever is in the Carpet position, and it is t ... Eureka Smartvac 4870 Bagged Upright Vacuum

Whenever I push the Bissell Proheat the brushes catch on carpet

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Brush Roll belt won't engage on WindTunnel self-propelled

When you had the brush roll off, did the ends turn freely? If not then the brush won't turn and the belt will just slip. You would have to replace the brush roll if either of the ends are frozen. Other then that you would have to remove the top co ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover windtunnel u6476-910. Brush does not roll. Flat belt and other belt are good. The other thicker belt (called V belt?) does not have tension with the brush roll. How do I make sure it is engaged? Is there a fix? Settings are in "Carpet", "Roll-on", etc. Cleand all hair and bags/filters already.

These machines had a defective switch and a bulletin was sent out to all service depots. If you contact any Hoover Warranty Depot, they will replace the switch, wiring harness and tool receiver under a no-charge warranty. It doesn't matter how old it ... Vacuums

My Dyson is not picking up on the carpet as good as it use to. The brush doesn't seem to engage on the carpet unless I hold the angle upright. It's very uncomfortable to hold it at that angle. What would correct this problem?

Brushes do wear out. Compare the length of the bristles on you brush with a new one. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The vacuum is making a noise like something is stuck when it is in the carpet position but not when in the floor position. I can't find anything that is stuck in the areas that I can see. I have cleaned the brush but it does not seem to want to turn. Does this machine need to be oiled so the roller will turn? Is there a way to check inside the motor? Do you think that because the brush won't turn that is making the noise? Do you know of any repair shops in the Lake Havasu City, Arizona area?

As far as the roller brush goes, yes, it does need to be cleaned. Follow the directions to remove it and clean as best you can of all debris. On both ends of the roller brush there will be two "holders" of sort that connect the brush to the frame o ... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0695 seconds