Having problems with your Dyson DC14 Bagless Upright Cyclonic Vacuum ?

My dyson is stuck on bare floor mode. It makes it very difficult to vacuum carpets. Can I fix?


Answers :

Repair Help & Product Troubleshooting for Dyson DC14 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dyson is stuck on bare floor mode. It makes it very difficult to vacuum carpets. Can I fix?


... Dyson DC14 Bagless Upright Cyclonic Vacuum

Loud noise I have a brand new Dyson and it is great on all my floors except one of my area rugs when it starts making this really loud vibrating noise. I am not sure why - nothing is stuck in the roller or vacuum and it doesn't make it on any of my other rugs. Also it is really hard to push whereas all the other floors it just glides. I don't want to return it but I also don't want to hear this sound every time I vacuum.


This is the clutch as it jams up in the brush. Usually happens with rugs that are not secured to the floor. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The vacuum is making a noise like something is stuck when it is in the carpet position but not when in the floor position. I can't find anything that is stuck in the areas that I can see. I have cleaned the brush but it does not seem to want to turn. Does this machine need to be oiled so the roller will turn? Is there a way to check inside the motor? Do you think that because the brush won't turn that is making the noise? Do you know of any repair shops in the Lake Havasu City, Arizona area?


As far as the roller brush goes, yes, it does need to be cleaned. Follow the directions to remove it and clean as best you can of all debris. On both ends of the roller brush there will be two "holders" of sort that connect the brush to the frame o ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My vacuum is making a loud noise like I sucked up somehting I shouldn't have I have cleaned all the hair and made sure there was nothing else stuck in there but it continues to make that loud noise is there something else that will cause it to make this ugly noise, and how can I fix it


... Dyson DCO7 Upright Vacuum

Whistling noise I just bought Dyson dc 33 multi floor plus about a month ago and use it 6 times because the carpet get dirty / dusty so quickly living with 5 other people in the house and when I use it today by stepping on the foot thing to make it to go down and when I push the botton it makes the whistling sound why is it like that I have read every instructions several times , does that mean I need clean the filters or need to get it fixed . When I first used the vacuum it was not like that a


... Dyson DC-33 MultiFloor Upright Vacuum Cleaner

Dyson DC07: When I first got this vacuum, it was so powerful that it lifted my area rugs off the floor. It is so weak it barely works. I have removed and cleaned the filter, but I can?t seem to improve the suction. What am I doing wrong? How do I fix it?


Hello,\015\012\015\012If your vacuum runs but still leaves dirt behind, the culprit could be the drive belt or an obstruction. If the agitator brush slips or won't turn, the belt is bad and needs to be replaced. If suction is weak when yo ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My Bissell series 65832 vacuum's rotating floor brush is making a really loud noise like its hitting something when ever I turn it on. Can you tell me how I can fix .


It probably needs a new belt, unplug the unit and find the screws that hold the cover where the belt it,remove them and look at the belt.Or it could have string or something wrapped around the brushes that would need to be cut out. ... Vacuums

Rainbow Vacuum, about 5 yrs old (bought new, no issues prior) - my 6yr old tipped it on it's side while water was in basin. Now when I turn the power on, it makes a very loud sound in the motor and you can feel the vibration on the floor. The suction still works and basin still catches dirt - the noise is just so loud and I'm not sure if I should continue use or how to fix -?


Although a wet/dry vacuum, it cannot tolerate water in the motor. Water will cause the motor to short out, which will cause the motor to act/sound like yours does now, if it continues working at all.\015\012To prevent additional problems, the ... Rainbow E series Canister Wet/Dry Vacuum

My Hoover vacuum is not vacuuming the carpets or floors. When I release the tube to use the smaller end the suction works perfect. So i believe the problem is in the rods on the floor or in the part that vacuums the floor! Can you tell me how to fix it , or where can I take it to get it fixed? thanks


Ive just had the exact same problem. In the very back lower portion of the vacuum You will need to take it apart. I guarantee there is a clog. You might also check your belts to make sure they are still on track. ... Hoover Vacuums

I have a Harmony vacuum and need it only for bare floors. The attachment I have seems to be too rough on the floors. I just need a simple attachment with soft bristles for a bare floor that will fit this vacuum.


Take the lower portion of your wand to a vac shop and ask for a universal fit wide floor brush with NATURAL bristle. The soft bristle is much better quality and will clean deeper into grooves in your wood floor or and tiled area. ... Electrolux Harmony Canister Vacuum - EL6985 Vacuum

The brush on my Hoover Windtunnel T series won't turn when I'm vacuuming carpet. It does, however, turn when I'm vacuuming bare floor, and I didn't think it was supposed to do that.


1) test the belt +brush for worn and replace2) test the motor God bless you ... Hoover WindTunnel TSeries Bagless Upright Vacuum Cleaner UH70107

I have a Dyson vacuum cleaner ...upright....all of a sudden my vacuum started making this awful sound...like a loud buzz...but only when I have it on carpet....when I have it on "floor" mode it's fine....sometimes(although seldom) it has worked without buzzing...and it's LOUD!!....I have only had this vacuum for a year....and no...I have never picked up any coins or hard stuff.only use it for 2 rooms.the rest of the house is wood floors.......what shall I do? Thanks......Gloria


It may just be, that on carbet the brushes make noise that you dont hear on woodfloors.\015\012If there is a hights adjustment, set it higher for shaggy carpet and lower for berber. ... Vacuums

My vacuum just stopped working, so I don't know what the problem is. I used it in the kitchen to vacuum the hard wood floor. I turned it off, and a few minutes later, turned it back on to finish vaccuuming the kitchen floor. It just would not turn on. I had not unplugged it or did anything to it. I then tried to see if it would work in another plug, and no luck. I'm trying to figure out if it can be fixed or if I need to look for a new vacuum.


When I get most Vacuums that have dies on people most of them the wire has been worn and cut one or more wires on the plug cord. Sometimes the cut can be over looked. Please unplug and check the wire carefully.Also please post the make model a ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

Dc07 when vacuuming motor and roller part will not stay on floor , as you pull and push the vacuum the brushes keep lifting up and I have to push it down onto the floor how do I fix this?


Most dc o7 do require a little wd40 at the hinges however if problem isn't fixed try looking and making sure all the peices are snapped in like they're supposed to be. hope this helps ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The roller-brush on my Dyson DC17 makes a terrible noise at all times. I removed the cover and extracted all debris from this area, making sure all connections were as secure as possible, but that didn't improve it any. The vacuum still seems to vacuum okay, but the noise sounds horrendous. How do I fix it?


Check the belt to see if a layer or piece of it has come loose and is flappping around.\015\012Check for any loose parts that could be getting hit by the brush or other moving parts.\015\012Make sure the brush it tightly in place and can ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My Model number 11635923502 kenmore vacuum is making a deep suctioning noise as if something is stuck in it. We have cleaned out the filters and all the vacuum lines thinking it was clogged. It is still making this noise and we are frustrated as to what could be causing this problem. The unit does not have much suction.


... Kenmore Progressive Upright Vacuum with InteliClean System Slate Blue

Kenmore Vacuum 116.36623501 does not stay on bare floor setting


It sounds like there is something wrong with the latching assembly. GO to the Sears Parts website and enter your Model number. Look at the parts assembly for the Nozzle, and the problem will be in one of items 12 through 17. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Clogged vacuum Rather stupidly, my boyfriend 1) were vacuuming without a bag and 2) vacuumed up a big piece of cotton from a sofa cushion. And now it's making a horrible noise and I see it vibrating where the tube connects to the machine. When you look inside there's a white thing sticking out but it looks like it's part of the vacuum. If it's a clog, how do you fix it? I tried unscrewing the tray the bag sits in but it won't budge.


You can start by taking off the bottom plate or top cover, which ever comes off, that is where the inlet starts going in and hopefully the clog is there. Could be in the hose also. But without the complete model number I can't look it up to see a p ... Kenmore 31912 Progressive Direct Drive Bagged Upright Vacuum

My son dropped the vacuum down the stairs and now the vacuum works but the front part of the vacuum does not drop back down when vacuuming any type of floor. It slowly drops and does not stay on the carpet. hope this makes sense. I have cleaned filters and suction seems strong at the small hose. the beater bar rotate very fast still.


May be part missing. this is unit has 5-year warranty.you can send to service. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Vacuum cleaner makes very loud noise when starting to vacuum - like something is stuck in roller area


Hi there,I'm sorry to hear you're having difficulties with your DC33. The brush control is designed to make a ratcheting sound to warn you if something is obstructing the brushbar. If you've checked the cleaner head and brushbar already, I'd ... Dyson DC33 Animal Bagless Upright Vacuum

I have an electrolux renaisence vacuum. the brush in the floor attachment turns but I have no suction. When I change to bare floor option on the handle the brush stops turning (correct) but I still have no suction. The lights on the handle showing --floor,carpet, high and low all work.


Sounds like you have a clog, either in the hose or the inlet by the brush roll. ... Vacuums

Why doesnt my Dyson auto adjust on our carpet? We have a taller, soft carpet and it digs into it, making it very difficult to vacuum. We have had the vacuum for about a year at another house and it worked GREAT on the berber......our new has a tall carpet somewhat like shaved berber and now the vacuum wont work.


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Henry brushes seem to catch in the carpet when pulling-will the brushes soften and make it easier to use as it makes the head bounce of the floor a bit when pulling making it harder work to vacuum?


There is a "see-saw" type switch on top of the cleaning head (the part that you push across the floor). This raises and lowers the brushes according to the type of floor you are vacuuming. Move this switch to the other postion and you will find that ... Henry Vacuums

My Kenmore 35922 works well on floors, but it recently became very difficult to push on carpet. The brush spins and a local vacuum repair guy wouldn't solve my problem since the vacuum worked fine on his very flat, commercial carpet. What can I do to get my easy to push vacuum back?


Hi dalee196,There are three common reasons why vacuum cleaners are getting hard to push.1. Base is dirty - The base needs to be clean from dirt and tar.2. Height is too low - You might want to consider adjusting th ... Vacuums

Got a curtain stuck in vacuum now makes funny


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1010 seconds