Having problems with your Dyson DC14 Full Access Bagless Upright Cyclonic Vacuum ?

Great suction through handle, no clogs anywhere,

\015 Great suction through handle, no clogs anywhere, does not pick up good any more, leaves trash still on floor\015

Answers :

OK - there are two obvious things to check: 1. Make sure the brush is rotating. The DC14 has a 'brush control system" operated by a knob on the base in front of the right side wheel. Make sure this hasn't accidentally been moved to the "off" position. With it in the "on" position, switch the machine on, tilt the handle back and check that the brush roll is rotating. If it isn't, then there's a broken belt or a problem with the clutch mechanism in the brush control system. 2. If the brush is rotating, switch the machine off (and unplug it), turn it over and you will see a short length of clear plastic hose with spiral reinforcing that runs from the brush area to the motor. That hose often develops a split (which lets air in and reduces suction around the brush). Take that hose off (pull it off from the motor end and then unscrew it from the brush end) and inspect it carefully for any damage. If it is damaged, get a new one - don't try and repair the old one, it's not worth it.\015\012
\015\012I hope this helps - if so, please remember to rate my response. If you need more help, just post a reply here and I'll see what more I can do. Good luck!
Repair Help & Product Troubleshooting for Dyson DC14 Full Access Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Great suction through handle, no clogs anywhere,


OK - there are two obvious things to check: 1. Make sure the brush is rotating. The DC14 has a 'brush control system" operated by a knob on the base in front of the right side wheel. Make sure this hasn't accidentally been moved to the "off" position ... Dyson DC14 Full Access Bagless Upright Cyclonic Vacuum

No Suction I get great suction in the hose, but when I plug the hose back into the unit, there is no suction and the air flow indicator line goes completely red. I've changed the bag and filters. I took the small panel off the back and made sure there is no clog, and took the hose off to make sure there was no clog there. Still no suction. Please help.


I about to say that's always a clog of some sort that causes that ... Miele S7210 Bagged Upright Vacuum

No suction I have new belts. Everything is clean. No clogs. When I turn it on it smells like rubber , the brush doesnt spin. Everything seems to be free flowing.. Roller brush isnt stuck on the ends. Took off hose to make sure no clogs anywhere. There is not even suction thru the hose with the handle in upright position.


Generally, the problem is that the belt is not running the brushes.  This is caused by one of the following:\015\012\015\012\015\012beater brush is jammed.  This is either an object stuck in the brush or im ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Either the hose has a clog, or the inlet down by the belt is clogged. Is there suction at the end of the hose, if not then it is clogged. If there is suction, then it has to be clogged down below by the brush roll, check that inlet. There also is ... Vacuums

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Mine does the same thing. There is no suction. I found that there is a door that opens when you tilt the handle in the down possition. I think there should be a spring in place so it can open. Until I find a replacement spring I have to open the door ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

My Lindhaus Diamante 300 has great suction but clogs


Sounds like you have some form of an obstruction in the hose ( i once found a tooth pick sideways in mine) most models allow for the hose to be disconnected from the vaccum itself, also make sure theres not a setting for attachments also, some models ... Lindhaus Diamante 300 Upright Vacuum

No I did not my hose on the dirt devil does not have much suction on it I took everything apart and found nothing wrong no clogs anywhere but when I add an attachment to the hose it loses all suction...I looked for a switch to change from regular vacuuming to attachment found nothing why is this??????? Need a manual where can I find some information and a download on line manual??????


Try this. There should be a little filter unerneath the tank. just clean that filter or replace it. (9 times 10) thats the problem.\015\012\015\012good luck. ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

I have a Bissell pet hair eraser model #3920. It's been working great until last night. I went to use it and the brush won't spin. It also smells like it's burning. I checked the belt and it looks fine, and the brush spins by hand easily. It's not clogged anywhere that I can see. Anyone have any other ideas? This vacuum is only 8 months old.


- Remove the access panel, which is on the bottom of the machine. There are 4 tabs to lift on the access panel to remove. Start with tab 1 then 2-4 tabs.- Check the brush, and belt for any damage. Clean off any debris on the brush. ... Bissell 3920 Bagless Upright Vacuum

The brush does not work on my dc15 animal, there is great suction but after about 20 seconds it sounds like something has got blocked in it although nothing is clogged, filters and hoses have all been cleaned but the brush still wont go round


Hi there,Sorry to hear you're having a problem with your DC15. You might find it helpful to visit the Support section of our website and follow these simple steps: ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Just got spinscrub this afternoon and worked great until had to empty dirty water. Now there is no suction at all. Have tried to find clogs and nothing to be found. Am about to return the damn thing!!!


Ok 3 things to check before re-boxing it up. 1) make sure that the lid is on properly. it should go on with the 2 tabs at the front of the machine, then click into place at the back of the machine. 2) when you emptied it, some ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I took apart the vacuum, did what you suggested and cleaned out clogs ect. all areas of suctions work great but just sucks in dirt spits it back out.


... Dirt Devil M110000 Bagless Upright Cyclonic Vacuum

The hose works great, but when I try to vacuum the carpet it doesnt work. The brush is turning, but I don't feel much suction. I checked for a clog and didn't see any.


You probably need the clutch replaced. This needs to be done every 1 to 2 years for most people ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have looked online for this vacuum but could not find it. The closest one is the Eureka 8803 but the p/n on mine says 79307. I have totally disassemble this vacuum. There are no clogs anywhere. Motor spins by turning shaft. Belt is new and turns brush. It still has absolutely no suction.


... Eureka Boss Capture 8803AVZ Bagless Upright Vacuum

Great hose suction, awful floor performance


Lose of suction usually means a clog either in the hose, dirt inlet by the brush roll and clogged filters. But a belt that has stretched to where it won't turn the brush roll under load will make it appear as no suction. If you have replaced the be ... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum

Electrolux canister model #1205. worked great. got a new hose and if you check the suction with your hand, great suction, but then the check bag light turns on and machine shuts off.


... Electrolux Vacuums

Electrolux vacuum model #1205. worked great . then got a new hose and if you check the suction with your hand, great suction, but the check light turns on and the machine shuts off.


... Electrolux UltraLux 2000 Bagged Canister Vacuum

Hoover Windtunnel T-Series UH20700 9 mos old. Keeps clogging in hose just above the beater brush assembly. I think it clogs because the suction is too weak to pull much through. Primary filter is clean and HEPA filter is replaced. Even when everything is unclogged, suction is weak compared to another unit (same model) that a friend has. Any ideas?


... Hoover UH70120 WindTunnel TSeries Rewind Bagless Upright Vacuum Cleaner

Poor suction The actual sweeper seems to work ok, but the hose attachment has some suction but not enough to pick up things I think it should and not enough to make the power brush spin. I've checked everywhere I can for clogs, but I can't see anything. And there doesn't seem to be any way to check to hose itself for clogs. I've cleaned out the container and the filters, but there's still a problem.


Check the inlet down by the brush roll, make sure it is open, if it is then the hose itself must have a clog. If the hose comes off, drop something like a marble in one end and see it it comes out the other end, if it doesn't then you have a clog. ... Dirt Devil M1100009 Reaction Soft Touch Cyclonic Upright Vacuum Cleaner Vacuum

No suction the vacuum runs, but there is no suction. I've checked the hose and the foot, there are no clogs there. The canister was pretty badly clogged, but I've unclogged as much of it as I can get to. it doesn't seem to come apart any more. I've cleaned the filter as well


The hose can clog up insid where you cant see it my husband takes it off and runs water thru it to flush stuff out lets it dry then reconnects it ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum

Poor Suction Heya! So I just picked up a used Dyson, but when I vacuum with it, the suction is pretty weak and it spits all kinds of stuff out the back and into my feet. When I pull the hose I have good suction, but in regular mode it hardly picks up anything. The brushes are spinning, and it eventually will clean an area if I go over it again and again. Maybe a clog somewhere? Please tell me that Dysons have better suction than my $50 Dirt Devil! Thanks!


I recently bought a second hand Dyson DC07. Its suction was poor. I removed all the un-clipable pipe bits and to remove any blockage but it all looked clear. The Final Sponge and hepper filter did have a lot of dust in it and the rotating brush was f ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hi my dyson dc18 has great suction from wand but when you got to use the vac for floors little suction but wand still got suction even while vacuming floors is it suposed to stop suction from wand


My Dyson dc18 had the same symptoms. The wand worked well and the floor bar had no suction. After removing pieces & shoving my fingers into the machine (no blockage) I found the suction pipe rotates between two positions (floor and wand). It look ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

Lost suction my DCO7 lost suction in the hose I started taking it apart and cleaning it and looking for clogs (probably more than I should have) and when I put it back together it has awesome suction in the hose but no suction in the base. It just pulls the pine needles up (christmas tree) but they never appear in the "bag" compartment and when I look they are just all gathered in a clump in the bottom by the brush.


Hi.\015\012\015\012Remove the sole plate turn the 3 plastic screws to unlock & lift off.\015\012\015\012Now remove the blockages that have accumilated from the oppening of short clear hose.\015\012Check you can turn ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Suction Cover The suction cover of my Eureka Deep Steam 2575A is broken - the tabs snapped off of the cover so I am unable to screw the suction cover back on. I need to purchase a new suction cover but can't find one anywhere. Anyone know what I can do? thanks


The exact same thing happened to me. i just called and ordered it from eureka. the number is 1-800-282-2886. the cover cost 13.07 and the s ... Eureka 2576A Steam Vacuum

The vacuum i've had for 6 months has very liittle suction power. checked that the belt is on. cleaned filter. checked to see if hoses were clogged. I used a super vac to suction any debris out of vacuum. still little suction power


As this unit has 3 filters on it, a lot of people forget about the one filter that will cause all of your trouble here. \012\012There is the exhaust hepa filter, no problem, your unit is pretty new, it shouldn't be a problem. \012Th ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

The suction for carpet cleaning is great but there is very little suction through the hose. I have cleaned out the hose but there is still very little suction. What else can I do?


Have you tried cleaning the hose from the vacuum end, the end that feeds the sweepings into the cannister/bag? Might be something close to that end of the hose.\015\012Also, one reason for a hose not to work is the possibility of a cut or broken hos ... Eureka 5849A Boss Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0486 seconds