Having problems with your Dyson DC14 Full Gear Bagless Upright Cyclonic Vacuum ?

How do we fix roller brush on dyson dc14 full gear?

\015 Roller brush is not working. We tried cleaning it and making sure the handle was in the correct postion. It still will not rotate\015

Answers :

Have you also checked that the brush control knob is set to "carpet"? The brush will not spin in "bare floor" mode. (Sorry if this seems too obvious to mention, but I see lots of Dysons where incorrect setting of that knob is the only problem.) Failing that, you almost certainly need a new drive belt.
Repair Help & Product Troubleshooting for Dyson DC14 Full Gear Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do we fix roller brush on dyson dc14 full gear?


Have you also checked that the brush control knob is set to "carpet"? The brush will not spin in "bare floor" mode. (Sorry if this seems too obvious to mention, but I see lots of Dysons where incorrect setting of that knob is the only problem.) Fail ... Dyson DC14 Full Gear Bagless Upright Cyclonic Vacuum

Roller brush is not turning on a dyson DC14


Http://www.dyson.co.uk/support/help.asp?product=DC07-SY&article=527\015\012here's a link that might help \015\012good luck ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a dyson - bought it 3 yrs. ago and the roller brush stoped working - doesnt pick up anything. Can you help? The brush doesn't roll or spin. Where can we take it to be fixed and is it under warrenty? THis


Don't worry it's probably just that the belt has broken or stretched. Your actually supposed to change them yearly. So if its been three years thats probably the case. Here is a link to the belt you need and a manual with instrutions: ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Roller brush is not turning on a dyson DC14


... Dyson DC07 Bagless Upright Cyclonic Vacuum

My dyson dc25 just turned off while i was using it first the roller brush stoped turning so i used the hose and now it turned off and wont turn on how do i fix it?


... Dyson DC25 All Floors Bagless Upright Vacuum

Bissell vacuum blet smells burnt - Dyson DC14 Full Gear Bagless Upright Cyclonic Vacuum


Replace the belt but clean the motor shaft first there may still be rubber from the old belt on there and will cause the new belt to go bad earlier ... Dyson DC14 Full Gear Bagless Upright Cyclonic Vacuum

My dyson DC17 animal has started to make an extremely loud noise after a rug got caught in the roller brush. What do I need to do to fix it?


Probably a flat spot on the belt, replace the belt ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I replaced the clutch in the dyson dc14. it isnt making that terrible noise anymore....thank god!! but the roller brush is not moving when the vacuum is in use. whats wrong?


The "horrible noise" you were hearing before wasn't the clutch! It was the roller brush. If the brush is not turning, all you are doing is burning out your new clutch. Reasons for the brush not turning: there is hair, carpet fiber or other matter wra ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Ive put a new roller brush in my dyson dc14 now it makes a awful noise


Hi There, I work as a tech for VacuumSpot and the problem you are describing is pretty common. It generally happens when you replace the belt or roller as the new one isn' ... Vacuums

My Dyson DC 07 roller brush won't spin . HELP? how do I fix it?


DC07s have two drive ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Dyson DC14 and the brush does not spin but the belt is still in place. how do i fix this problem?


Call dyson they will help you reset the vacuum //\012\012it has a reset bottun on the right side\012\012\012hope this helps ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The roller-brush on my Dyson DC17 makes a terrible noise at all times. I removed the cover and extracted all debris from this area, making sure all connections were as secure as possible, but that didn't improve it any. The vacuum still seems to vacuum okay, but the noise sounds horrendous. How do I fix it?


Check the belt to see if a layer or piece of it has come loose and is flappping around.\015\012Check for any loose parts that could be getting hit by the brush or other moving parts.\015\012Make sure the brush it tightly in place and can ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Dyson DC14 It started making a high pitched squeel so I took the filters out and cleaned them and i checked all places that pull out on the vacume to see if there was anything clogged. I also cleaned the roller brush. but when I turned it on, after a couple of seconds the sound came back again. can you help


Sounds like motor bearings are gone .... sorry. ... Dyson Vacuums

Dyson DC14 animal vacuum does not turn on however the roller brush does come on.The hose was clogged and that was cleared but vacuum still will not turn on.


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Roller brush of my dyson dc07 isn't turning...


It migh be the belt.check your belt or it is the brushroll is stuck.(from to much hair ect.) ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson DC07 brush roller is worn and won't make contact with the carpet anymore. I need to replace the brush roller but don't know how...HELP?


Buy the brush over the web etc..\015\012\015\012To take the brush out \015\0121 - Take the outer covering - uese a penny to turn the yellow srews\015\012\015\0122 - Slide the black brush out from the assembly - Try the n ... Dyson DC07 Allergy Blue/Turquoise Bagless Upright Cyclonic Vacuum

Brush Roller Wondering if I need a new brush as well as a belt. The Roller seems to have trouble spinning when it makes contact with the carpet no matter how the height is set. Everything else seems to work fine. Do I need a new roller to fix this problem?


The bearings can go bad in the brushroll. It may need replaced, even if the brushes aren't worn. Helpful link....\015\012\015\012 ... Kirby G6 Bagged Upright Vacuum

Riccar model rad.7 upright (radiance). roller brush won't turn and red roller brush indicator is on. roller will turn easily by hand and belt is in place. how do i fix this?


As you already know, the red brush indicator light indicates that the brush roll has stopped turning, usually because an object has become stuck in the brush roll. When that happens you should turn the machine off (unplug it also for safety), remove ... Riccar 8955 Upright Vacuum

I'm trying to figure out which dyson vacuum is better, the DC14 or DC17. from what i read, the DC17 is the newer model of the DC14, the DC17 added an extra motor for the brush, but from the dyson site, the DC17 has less suction power. it went from 250AW (dc14) to 220AW (dc17). is that a significant difference that i should be worried about?


Hi,DC17 is much better than DC14. I always believe User's review are much better than what Features Company usually Displays.Read :-http://www.epinions.com/review/Dyson_DC17_Animal_Vacuum/content_404790546052 ... Vacuums

My Dyson Animal has good suction and works fine for actually picking up dirt, but when I use the vacuum with the roller, I hear a grinding/rumbling noise. Its only when I use the vacuum with the brush rotating. It does not happen hen I shut the roller brush off. The belt is fine. I cannot figure out what is wrong as there are no clogs, debris, or foreign objects stuck in the brush or in the belt. The noise seems to be the only issue. The vacuum picks up fine. It just doesn't sound right a


Trace the path of the suction into the tank and see if there is anything loose or ingested.\015\012Also, remove the brush and clean as best you can. Perhaps there is something caught in it. Lubricate where it makes sense with some WD40. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My Eureka Boss 4870 belt keeps fraying, stretching, and breaking. When I replace the belt and turn the roller brush by hand, within just a few turns the belt drifts off center and to the left of the roller brush where it starts to rub. How do I fix this?


... Eureka Smartvac 4870 Bagged Upright Vacuum

Roller brush on Dyson D25 not working. Have removed roller brush and cleaned it as per instruction booklet advise. But to no avail.


... Dyson DC25 All Floors Bagless Upright Vacuum

I caught a hidden shoe lace in my dyson 17 beater head....shut it of quickly....removed the lacing from around the head....loosened the three screws on the botton of the head....cleaned it out from whatever little dust there was....checked the heads belt reset the roller brush into the head...but alas no beater brush action. what to do?(I've had my dyson about5 months....HELP!. thanks, Jan Selman


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

How do I replace the brush on my dyson dc14 - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum


Hi its Darran at Dyson. If your DC14 has a brush control, we would only recommend that a suitably trained person attempts to replace the brush bar. We can arrange a repair so that one of our engineers can replace this for you, ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0728 seconds