Having problems with your Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum ?

Beater brushes don't work, what to do? They only work when the canister is in about an 85 degree up position.

Answers :

This appears to be a loose connection. The below post was answered by highntools a while ago. It probably is related to you problem.\015\012
\015\012I have finally fixed my sister's dyson dc 15 beater bar \015\012problem. It was just 2 tiny \015\012broken wires connect to circuit board lead to the beater bar. The wires \015\012broke where they go through the black rubber gommet. You need a torx screwdriver \015\012tx 15 to remove 2 plastic covers to access the wires. When looking at the front \015\012of the vacuum, the gray covers located on the right side of the vacuum. 1 big \015\012cover with a black rubber gasket and other small gray cover is on the rotating \015\012ball area.
\015\012\015\012There have been several people who reported loose or burnt wires to be the \015\012culprit for the brush bar not working. The DC15 does not use a belt, but a motor \015\012that is control by the circuit board. And I really \015\012believe that in your instance, the problem is a loose wire between the circuit \015\012board and the brush motor.\015\012
Repair Help & Product Troubleshooting for Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Beater brushes don't work, what to do? They only work when the canister is in about an 85 degree up position.

This appears to be a loose connection. The below post was answered by highntools a while ago. It probably is related to you problem.\015\012\015\012I have finally fixed my sister's dyson dc 15 beater bar \015\012problem. It w ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

My beater bar is not turning so the vaccuum is not picking up. The belt is not broken. The motor is working and I can see the cyclone effect in the canister. I have checked for blockages. I have cleaned the hair and string from the beater bar brushes. What should I do?

You need to replace the belt, it has probably broken. Your actually supposed to change them yearly. Here is a link to\015\012the belt you need and a manual with instrutions: ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Wont **** the beater brush works but it's not sucking stuff into the canister

Sounds like a blockage some where take apart the hoese and clean them one at a time ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

The rotating brush at my new bissel vacuum doesn't work. The belt is OK, the canister is empty and clicked into position, no clog???

... Bissell 3750 Lift Off Bagless Upright Vacuum

Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?

Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula

There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

Have a Hoover model S3670 and the beater brush no longer spins. Have checked the beater belt and it is good, did find out that the light bulb in the unit was bad. Any suggestions on how to test the motor that drives the belt or determine the reason the beater brush is not working?

I usually test the motor with a cord with alligator clips on the wires, and attach them to the black and white wires on the motor ( remove the belt first ). A very common problem with this model was a short circuit developing in the short cord that r ... Hoover Vacuums

How do you open the power head to remove the beater brush on a kenmore 116 canister? I have a piece of twine wrapped around the end of the beater brush

Greetings,Thank you so much for that clarification, I know the exact model of Kenmore that you have now. This model is actually made by Panasonic for Sears who puts the Kenmore name on it. I wasn't able to located the Sears owners man ... Vacuums

I replaced the beater brush and works on carpet but when I turn the beater brush oof to do floors, the vacuum shuts off.

... LG Electronics Kompressor Pet Care Upright Vacuum Cleaner LUV200R

Just purchased my Dyson Ball DC24 less then a month ago. Its great when it works. The brush does not spin. At first I was able to get it working after repeatedly pushing the brush button and fooling around with the handle position. Now nothing.

If its still undr warrenty take it back i wonder if the switch is broken or a bad connection .i hope this works thanks ... Vacuums

Beater bar brush stopped working...

Does the power head motor stop, or does the brush roll stop. If it is the brush roll stopping, replace the belt and/or the brush roll. If it is the motor, you may need to clean out around the motor, it may not be getting enough air to cool causing ... Rainbow E series Canister Wet/Dry Vacuum

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help

The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Kenmore canister vacuum model 116-25512506. It has a 2 stage switch on the handle, the vacuum motor will not work, the carpet beater attachment does work, the vacuum motor will not cut on at all with either stage, 1st stage is vac only, 2nd is vac a carpet attachment. Carpet attachment will work, vac does not.

Try to find the reset button. It should be somwhere near the bottom area. It looks like a red dot that you can push inward. If you can press and hold the reset button, it will restart your suction and solve your problem. ... Vacuums

We have a kenmore canister vacuum and it runs but when turn on the rug clener brush the brush will not run we then put on small brush head and that will work

If the power head motor runs, but the brush doesn't turn, then the belt is broken. Replace the belt and it should work. ... Kenmore Vacuums

Brush works intermittedly - I've looked at the common solutions listed but none seem to work...shaking it & reseating the canister will get it working again sometimes but obviously that doesn't seem to be a very good solution. Can you help?

I just had the same problem. I would turn on the vac, and it worked fine. When I turned on the brush it would work for a few seconds then shut off. Through troubleshooting I found out it had nothing to do with a bad power connection. By chance I took ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu

This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

Belt drive not working. Won't turn beater brush.

You need to replace the belt. Here is the belt you need and the manual which has instructions: Dyson DC07 Belt and Manual ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Beater brush does not work. Brush is clean and belt is not broke. Dyson 07 animal vaccum

Even though the belt may not be broken it might be stretched and if that is the case it will not turn the brush. You can get replacement belts here:Dyso ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a canister with a beater bar which i love. I have sucked up a sock (or something) in the beater bar and it will not work. I can't get it open to check it out. We have misplaced the booklet that came with it.

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=820565\015\012Generic problem for all Vacuums\015\012I have a canister with\015\012Posted by DFundis on ... Vacuums

The belt on the beater brush is too loose and the brush won't turn, I have ordered new belts and it still doesn't work!!

Look in your manual for the proper routing of the belt, there may be piece broken and missing without you realizing it. If this not the case, there has to be some kind of adjustment on this unit. ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old

Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Have a Centralux Aerus about 5 years old. Don't see a model number. There is suction but beater brush quit working. Was using for a few minutes, shut it off for a few minutes, turned it back on and suction only. Tried the reset button also. Tried the sidekick attachment and it works fine. There was no smell like something was hot. Belt is fine. Are there any fuses or anything else to try? This vacuum cleaner has not really been used that much, it is hard to believe the motor would need replaced

There probably is a loose wire in the handle near the switch or a wire off near the swivel elbow near the vac power head. With the right fastener tool to remove some screws you can fix it yourself ... Electrolux Centralux Vacuum

The beater bar motor doenst work when i push the bar button the bar button doesnt light up like power button how can i test bar motor or bar switch or what is the common problem wiyh this model I have 2 that dont work the same way

If it do not work ...and you already are on the second one that behaved in the same way it may be a problem with the power in your place and the cause it may be the main fuse...Im not sure where is located in this model but it has to be near the powe ... Vacuums

The beater on my miele S344 canister stops and the light on the vacuum head comes on. I have already cleaned inside the beater brush area. What else can I do?

... Miele Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0989 seconds