Having problems with your Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum ?

When I vacuum the carpet it won't engage into the brush mode, or it does intermittenly. It stays in the brushless mode for the most part


Answers :

This appears to be a loose connection. The below post was answered by highntools a while ago. It probably is related to you problem.\015\012
\015\012I have finally fixed my sister's dyson dc 15 beater bar problem. It was just 2 tiny broken wires connect to circuit board lead to the beater bar. The wires broke where they go through the black rubber gommet. You need a torx screwdriver tx 15 to remove 2 plastic covers to access the wires. When looking at the front of the vacuum, the gray covers located on the right side of the vacuum. 1 big cover with a black rubber gasket and other small gray cover is on the rotating ball area.
\015\012
\015\012\015\012There have been several people who reported loose or burnt wires to be the culprit for the brush bar not working. The DC15 does not use a belt, but a motor that is control by the circuit board. And I really believe that in your instance, the problem is a loose wire between the circuit board and the brush motor.\015\012
Repair Help & Product Troubleshooting for Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

When I vacuum the carpet it won't engage into the brush mode, or it does intermittenly. It stays in the brushless mode for the most part


This appears to be a loose connection. The below post was answered by highntools a while ago. It probably is related to you problem.\015\012\015\012I have finally fixed my sister's dyson dc 15 beater bar problem. It was just ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

My vacuum will not engage to unlock to vacuum. I turn the vacuum on - that works fine. I put my foot on the part to make it so I can vacuum and it will not unlock. What could be the problem. SOO frustrating!


Hi there,I'm sorry to hear you're having difficulties with your DC28. The cleaner should recline easily into the vacuuming position when one foot is placed on the cleaner head, and the handle is lowered. If it's not doing this, check the clea ... Dyson DC28 Animal Bagless Upright Vacuum

My son dropped the vacuum down the stairs and now the vacuum works but the front part of the vacuum does not drop back down when vacuuming any type of floor. It slowly drops and does not stay on the carpet. hope this makes sense. I have cleaned filters and suction seems strong at the small hose. the beater bar rotate very fast still.


May be part missing. this is unit has 5-year warranty.you can send to service. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have an endurotronic 4111 electrolux vacuum called ''the boss'' and the cable wont retract into the vacuum when i depress the button on the top. how do i dismantle parts to have a look to see if it will repair or not. does anyone have a repair manual for this vacuum. thx


... Electrolux Vacuums

My dyson slim vacuum doesn't switch from hose to floor mode. I thought the foot lever was broken. I realigned it but it doesn't switch now from floor mode to hose mode. I take out the hose and I can see the white part. I thought it should move as you go from upright to recline position of the handle.


The changeover valve is not activating - call the Dyson helpline - they'll set you up for a repair with a repair dealer in your area. ... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow

Dc07 when vacuuming motor and roller part will not stay on floor , as you pull and push the vacuum the brushes keep lifting up and I have to push it down onto the floor how do I fix this?


Most dc o7 do require a little wd40 at the hinges however if problem isn't fixed try looking and making sure all the peices are snapped in like they're supposed to be. hope this helps ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Power button not engaging...vacuum will not stay


The power button is worn out and needs to be replaced. That vacuum is pretty simple. So even if you don't know how to take it apart it shouldn't cost much to have it repaired. ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Electrolux z4494 vacuum cleaner mains cable wont stay out


Opened up case as follows:\015\012- Open lid of bag chamber. Remove lid by gentry prising the hinge arms slightly further apart so the hing unclips from the body.\015\0122 deeply recessed screws now accessible at rear edge of bag chamber ... Electrolux Vacuums

I have a kirby G4 and the mini emtor is broke off. It looks like there is a piece that connects the mini emtor boot to the base of the vacuum. I was wondering what that part is or if it is just part of the mini emtor that broke off and stayed attached.


Hello, hrjI was trying to help you out here. Maybe this will help some? I was going backto some customers that asked questions in the recent past and even fartherback. It appeared that no one answeredsome of them, So, I thought I would tak ... Kirby G4 Bagged Upright Vacuum

Bag full light stays on so my electrolux diplomat lx vacuum wont start i push on/off swtch and light stays on


... Electrolux Lux 5500 Canister Vacuum

Kenmore vacuum handle wont stay up - Kenmore 25512/ 25513 Progressive Canister Vacuum


... Kenmore 25512/ 25513 Progressive Canister Vacuum

I have a bissell lift off and the brushes wont spin, i think it maybe because of the internal switch that tells the vacuum that the canister is installed is bad. is there a replacement part for that or do i have to get a new vacuum?


Hi,If you take out the brush roll, holding the ends, make sure that it \015\012spins freely, if not, replace it. Belts stretch after a short time of \015\012use and need to be replaced often.So you could either have a bad brush roll and ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

I have a dyson dc07 with a malfuncitoning clutch diagnosed here on fixya. I've replaced the clutch and the grinding noise when the clutch is engaged for carpet and non rotating brush problem presists. This is after replacement of the clutch with a new part. Install of the new part went well and there are no otehr apparent problems with the unit. Ideas? The unit is only a couple years old and not used that much on carpet. For an expensive vacuum I'm not that impressed with it at this point.


Greetings from GoVacuum,\015\012\015\012If you have replaced the clutch already, then this can really only be one other problem, and that is the roller brush. If the roller brush's bearing have locked up, and the brush is no longer spinn ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a


... Bissell ProHeat Deep Cleaner Upright Vacuum

Sew- Prow Sewing machine Model ZZ- 401 need diagram to order part and manual. Has broken missing parts in spool area spool wont stay in under needle Davy B


Hi!!\015\012\015\012Try this sites\015\012Hi!\015\012\015\012It seems that this is a common problem for this machine. I think you will be better off getting a new machine for $50 at this site\015\012 ... Vacuums

I had to change a cracked boot. The new part did not have the same pieces even though everything went together again. Now the vacuum turns on, the beater power head works but the vacuum won't stay on. What could be wrong?


It sounds as if they sent you the wrong parts, contact Kirby, let them know your dilemma they usually pride themselves on their customer service. ... Kirby G4 Bagged Upright Vacuum

I have a brand new LGV200R vacuum sweeper.. from the very beginning it never will stay turned on.. it is brand new.. I have checked every thing in the book that says to and then some.. why wont it stay ON


... LG Vacuums

My kenmore progressive canister vacuum powerhead wont stay on


... Kenmore 25512/ 25513 Progressive Canister Vacuum

Wont stay powered on


He is right - some parts for these are near impossible to find..\015\012\015\012Did he mention what parts are not obtainable ?\015\012\015\012This is a decent site that has allot of parts available -- ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

We have an electrolux Vacuume & the lower hard part that plugs into the power nozzle does not stay in. Cay U sendf us 1 new peice and a price on new bags & filters. Thanking U in advance. Mrs. B. Wells. Pls. reply to [email protected]


It costs around $5 to replace it u can get it in ebay too ... Electrolux Vacuums

When I vacuum w/ the brush control in the on position it make a really loud noise, almost like a grinding sound. I have looked at it and nothing seems to be wrong, but I notice that the pin that engages the belt seems to vibrate a bit, possibly creating the noise. It started when I accidentally got part of a plastic grocery bag caught in the brush. Could it have stretched a belt? Nothing is caught any other place and it only makes the noise when the brush in in the on position.


Yes, the belt could have been stretched and is now vibrating and hitting other parts and creating a noise if much of the bag got caught under the belt. If you have another belt for this vacuum, please put it on and see if the noise stops. If it does ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

Base of the hoover wont stay on the floor - Dyson DC07 Bagless Upright Cyclonic Vacuum


Check or replaced Upright Lock Assy\015\012part no:908821-01 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Dyson 15 "the ball". The beater bar will only rotate if the vacuum is engaged and the handle at a high angle. The bar stops when I drop the handle to a lower position. The condition is repeatable. Can you provide part and repair instructions?


If air is leaking in somewhere, you will not have any suction.\015\012\015\012\015\012Also there are some possibilities that has to be checked to confirm the fault.The problem is minor but the possibilities are too much for this pa ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Tray wont stay connected to kirby - Kirby Ultimate G Bagged Upright Vacuum


Here is a guide for the shampooer...follow it exactly and it should help. Please remember to rate it if it's helpful! :0)\015\012\015\012 ... Kirby Ultimate G Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0945 seconds