Having problems with your Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum ?

Brush does not spin all the time

\015 The brush does not always spin. Sometimes when I go forward it spins, when I pull back it stops. Sometimes it stops all together. I shut the vacuum off and turn it back on it may spin a couple times then stop. There is still suction and it runs, just the brush does not always spin, more not.\015

Answers :

HighnTools posted this solution a while ago. This might be related to your problem:\015\012
\015\012I \015\012have finally fixed my sister's dyson dc 15 beater bar problem. It was just 2 tiny broken wires \015\012connect to circuit board lead to the beater bar. The wires broke where \015\012they go through the black rubber gommet. You need a torx screwdriver tx 15 to \015\012remove 2 plastic covers to access the wires. When looking at the front of the \015\012vacuum, the gray covers located on the right side of the vacuum. 1 big cover \015\012with a black rubber gasket and other small gray cover is on the rotating ball \015\012area.
\015\012
\015\012The above was from HighnTools.
Followed the instructions on removing the 2 grey panels and fixed the blue/yellow wiring problem. The rubber gasket right at the crossing point broke the yellow wire inside the gasket. Hard to get to, but here's a pic of the area, vacuum upside laying face down. Bore out the gasket to make the hole bigger, fixed the wires, works like a charm.
8_23_2012_5_42_29_am.jpg
Repair Help & Product Troubleshooting for Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My floor brush stopped spinning, I cleaned everything out as per your directions in other posts and following the instructions in the manual. Now the floor brush wobbles and has a hard time spinning when upright. Looking at the end of the brush, opposite the drive belt, the bearing-type end that the brush spins on appears to be off-centered. Is there an easy way to fix this???


... Bissell 3130 Bagless Upright Vacuum

Have a spin scrub a couple of years old. Have used it maybe 5-6 times and the green brushes only spin if you take the tanks off and set the machine upside down and push the brushes toward the machine... the second you stand the machine up they quit spinning.


Repace the belt ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

The spinning brush on the side kept falling off. I would put it back on as the little screw usually remained with the brush. Last time it fell off (it has every time I've used it) I lost the tiny little screw. I cannot find reference in the manual to its specifications. As I have had it for less than a week, I am considering returning it.


Its so annoying to find Roomba after he's finished cleanin only to see that once again he's lost his brush. How to keep your Roomba from losing his brush- items needed: quick steel putty (local hardware store), crazy glue, original screw (or similar ... iRobot Roomba 530 Robotic Vacuum

Just purchased this Dyson dc24 today. brush doesn't spin after gettin tangled in a cord. removed the cord from the brush OK. I have several times: removed the brush and replaced it OK. pushed the red button by the brush. pressed the brush power switch.


When you removed the brush roller dod you examine the end of the actual roller that is opposite from the removal opening. There is a gear that the roller fits over that may have gotten stripped when it became tangled. Check that the gear has not roun ... Dyson Ball DC24 Bagless Upright Vacuum

Brush does not spin all the time


HighnTools posted this solution a while ago. This might be related to your problem:\015\012\015\012I \015\012have finally fixed my sister's dyson dc 15 beater bar problem. It was just 2 tiny broken wires \015\012connect to ci ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Bin isn't filling, won't pickup and brushes won't spin for the second time. Last time iRobot had to replace both wheel modules. Any suggestions? I clean it every time I use it!


Wheel modules? It's more likely to be the cleaning head module. Clean your brushes exactly as the manual describes-- particularly the yellow bearings. Run the Roomba on a hard floor without the dustbin. Does the brush turn? If not, call support again ... iRobot 560 Roomba Vacuuming Robot, Black and Silver Vacuum

Last time I used by Hoover it worked fine, took brushes out to clean them and now when I try to put them back in they won't snap into place and lock. Looks like all tabs on both sides of the brush piece are there and I spin the brushes for the center spindle to line up but it won't snap into place.


Just slightly turn the brush wheel, The tabs look square, but are just a little different in one direction ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Brushes only work when Dust Bin is removed!! I have cleaned & cleaned this thing! It runs for about 2 mins & stops, says "Clean Brushes"! and now it's very noticeable it's not picking up well... but is picking up a bit. I take the dust bin out, and the brushes spin.... and it has much more power.... and is very clear it is working! But it's useless without the dust bin! LOL It's only 9 months old.... called customer service, but it was the one time it worked just fine! Of course, I thought I'


HI, If the brushes work , without the bin, the problem , the problem could be caused , due the failure at the bin lock mechanism. There is a sensor that checks if the BIN is connected properly or not. This problem is best resolved by getting ... iRobot Roomba 560 Robotic Vacuum

I was vacuuming my room and all of a sudden I hear this loud noise, then notice the roller brush isn't spinning. Thinking too much hair was caught I separated it from the rod and hose to clean it out, but noticed that the roller brush didn't move at all while I was cleaning it. I've cleaned the brush before and it would roll around with little effort, but this time I couldn't move it at all. After removing hair and string I put the vacuum back together and started it up, but the noise continued,


It sounds like if the rod is clean then there is debree inside the roller where the rod fits in too. ... Hoover Platinum Cyclonic Bagless Canister Vacuum With Power Nozzle

I have an Oreck XL Platnium. It smells like burning rubber and the brush roller binds and stops as you pull it back and forth, even on a hard floor. I have changed the belt 2 times. I have taken the brush roller out and checked it. It seems to be spinning freely. What could be wrong??


... Oreck XL Ultra Bagged Upright Vacuum

I have a Bissell 7920 ProHeat and only used it 4 times and the brush on the bottom has stopped spinning and when attempting to spray solution the flow indicator doesn't spin and nothing comes out. I have looked at all of the belts and they seem fine. I have also removed and cleaned the heating unit. Still nothing. Any other ideas?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Hoover Bagless Hello,      My Hoover bag less (Model U5280-900) is not picking up dirt like it should.  The brush roll is spinning fine, but the bristles on it are only about one quarter inch long.  I am wondering how long they should be.  The vacuum is quite a few years old.  Do you think it is time to replace the brush roll.  Could you email me at [email protected] about this topic.  The product bar below did not contain my model no.  The correct model no. is above in my message.  Thanks


If the belt is more than six months old then change it even if it is not broken. then replace your filters if that doesnt work than check the hoses for a clog drop a marble down them and make sure it comes out. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

The rotary brushes on my Windtunnel V2 won't spin. I wasn't having any problems just, boom, no more spinning. I've had to clean hair and other stuff from them in the past. At that time, they wanted to move and couldn't. Now, I turn the machine on, and they don't move but make a loud noise. What do I need to do?


... Hoover U8147-900 WindTunnel V2 Bagless Upright Cyclonic Vacuum

The brushes are not spinning at all. I have checked them and they are snapped in securely. It was working fine last time I used the machine. I have cleaned them and they spin manually just fine.


You probably got a piece of foreign material jambed in there for a moment and it "smoked the belt" that spins the brushes,it will either have the belt on either side of the brush housing cylinder or like kirby vacs the belts around the cylinder and i ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

I have cleaned & cleaned this thing! It runs for about 2 mins & stops, says "Clean Brushes"! and now it's very noticeable it's not picking up well... but is picking up a bit. I take the dust bin out, and the brushes spin.... and it has much more power.... and is very clear it is working! But it's useless without the dust bin! LOL It's only 9 months old.... called customer service, but it was the one time it worked just fine! Of course, I thought I'd stop here first before calling again! Than


Ok, this is a "Brush Height Adjustment" issue. It will probably work great on a hard surface but on carpet the brushes bog. If you've taken the unit apart already...Sorry....do it again. When you do, you'll see a String which allows the brushes to " ... iRobot Roomba 560 Robotic Vacuum

My sd40025 dirt devil ..it is not a upright. it is the follow along, bagless vacuum. has wonderful pick-up but the brush stopped spinning when i was vacumming my rug..i love this vacumm but it is only the third time i have used it. It is brand new. Why would the brush stop after maybe 20 minutes of total use?..please advise


... Dirt Devil SD40020 Bagged Canister Vacuum

My Hoover Max Extract 77 brushes won't spin. I can't figure out why. I have only used it a half a dozen times!!


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hello have a Hoover steam vac model F5906-900 serial #120500259649 use three times. The motor does not spin the brushs the square shaft does not move iam sure it is broke inside. thanks


The turbine is what turns the brushes. If the shaft on top of the brush block is ok, then the turbine isn't working, you can try cleaning it, but replacing the turbine may be the best option. ... Vacuums

I have a Hoover SteamVac F5914-900 SpinScrub... The last time I used the hand tool attachment, it worked fine. Just tried to use it again, and now I only drips of water will come out of the hand sprayer, if that. I have tried prepping it for up to 15 seconds like the manual says... no luck with that. Also it is making a big puddle on the floor, probably because the brushes on the main unit keep spinning when I am trying to use the hand tool which I dont think they are supposed to do? Can a


The brushes can be turned off on most of them via a switch on the hood. There shouldn't be water coming out onto the floor unless you are pulling the trigger at that top. You probably broke this when attempting to use the tools. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I HAVE A BISSELL PROHEAT 2X HEALTY HOME, IT WORKED JUST FINE THE LAST TIME I PUT IT UP. YESTERDAY, I NOTICED THE FLOW GAUGE WAS NOT SPINNING, SO I CHECKED AND SURE ENOUGH NO WATER WAS COME OUT. I CHECKED AND ALL THE TUBS AND EVERYTHING ARE IN THE RIGHT PLACE AND HAVE LIQUID IN THEM. HAVE TRIED PRIMING CLEANING THE BRUSHES RUNNING HOT WATER THROUGH IT... HELP


Have you made sure that the tanks are seated properly and the red \012(or black) auto-load gaskets are in place. \012Check the bottom of the Water Tank and the Formula Bottle to make \012sure each has a red auto-load gasket attache ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Side brush doesn't spin all the time and doesn't go on some of my rugs


Hey tsahcub1. check if its screw is not released and if it is, tighten it,2. while doing so check for any dirt/hair and clean the pivot area.3, if that doesn't work, unscrew and take the brush out (pull straight)check its reve ... iRobot Roomba 560 Robotic Vacuum

Hoover SteamVac F7222-900 steamvac Brushes do not spin. Looked at filter as per manual instructions but it was free of lint. Need to fix it, help please? Vacuum was used less than 10/12 times


Solution for Hoover SteamVac (F7452-900) brushes not spinning\015\012Uses the turbine model and same solution would be similar. Root cause is simply the main gear attached to turbine becomes stuck. This problem shoul ... Hoover Vacuums

I have the Bissell Pro-heat 2X which is new and only used one time and today I am trying to use it and the brushes will not work at all. They will not turn and spin like they are suppose to.....Please Help ! John Baumgartner Roanoke, VA


Look on the front of the little gree guy and where the switches are you should see a small diagram of a brush above or below one of the switches flip the switch to the brush diagram ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Hoover floormax supreme hard floor machine.One brush spins the other doesn't. used one time last year.


... Hoover Floormax F4300 Upright Wet/Dry Vacuum

My pet hair eraser smells like it is burning all the time and sounds funny. The brush will not spin once you have it on the carpet unless you hold it up a little while you are cleaning but then the whole vaccume is not on the floor. I have cleaned all filters and all and it does the same thing. My sister has the same machine because I raved at how wonderful this thing was for pet hair and mine has not worked right since it was about a year old and hers has had the same exact problem since it was


We had the same problem, and it turned out that the roller wheel height setting had broken, for no apparent reason, and was "floppy" so we had to lock it in to one setting with epoxy. Limits utility, but it works. Sort of. ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0447 seconds