Having problems with your Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum ?

Switch for roller brush not working and brush not going round, any help plz?

Answers :

\015\012mikerobin143 's solution \015\012
Apparent common failure is that either the thin yellow and or blue motor drive wires that run from the LH side of the vacuum where the "control board" is located down into the hinge / ball area become stretched and then fray and eventually break. You need a Torx screwdriver to remove the LH panel ( 4 screws) and also an access panel (2 screws) at the side of the ball which permits access to the blue / yellow wire connectors. I replaced with a new wire and connectors having fed the wires through the access hole making sure sure enough wire was available for the movement of the handle. Also ensure that when the covers are replaced they do not trap any wires underneath.


Repair Help & Product Troubleshooting for Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Switch for roller brush not working and brush not going round, any help plz?

\015\012mikerobin143 's solution \015\012Apparent common failure is that either the thin yellow and or blue motor drive wires that run from the LH side of the vacuum where the "control b ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Hi my dyson is not sucking up very well when i put it on its side and switch it on the brushes are not going round when i put the white dail to on at the bottom the brushes go round but it makes a terrible noise i have cleaned the brushes checked the soleplate is on correct and taken the clear hose off and checked for splits the suction is there when i have been checking these things hope you can help thx

Hi there,Sorry to hear you're experiencing a problem with your cleaner. Please get in touch with us, free, on 08002980298 (UK), or 1866MYDYSON (US). We can run through some checks over the phone and provide you with the assistance you nee ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula

There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

After using switch to go from floor to carpet, noticed the roller brush not working, and therefore the self-propelled feature also not working. Replaced what I thought was the problem, a loose belt, but still does not work. Motor runs and there is suction...???

... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

Hoover windtunnel t series belt is loose- roller brush doesnt turn. Its brand new belt is slipping. we bough new belts and putthem on same problem. Can not find solutio in manual. Is the belt supposed to go around the "metal pulley". I know it goes around the little metal motor thing, then thru the guide and around the brush. What is the metal pulley??? Is is the larger round silver thing between the guide and roller?

I also have a loose belt and have bought additional belts but have the same problem. I put the it around the metal rotor and around the brush roller a shown by he Hoover video, and it is loose. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

On /off power switch works but when i engage carpet/floor switch nothing happens/ no light to indicate its working and roller brush not turning

... Miele S7210 Bagged Upright Vacuum

Dc15 fuse The roller brushes on my dc15 stopped working..I checked the obvious and then noticed that the 2 amp fuse was blown on the circuit board . I've replaced it with the same type bought from Maplins but it keeps blowing .. I tested the yellow an blue wires leading from the circuit board to the roller brush head and the are in tact and I can run a current through them ... Any thoughts from anyone .? Your help would be. Appreciated thanks Lee

Hi Lee,I'm sorry to hear you're having difficulty with your DC15. If you'd like some help, please give us a call on 0800 298 0298 - we may be able to resolve the issue with some troubleshooting over the phone.Best wishes,Jack ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

I have a vax cylinder model V-094. Working fine then started to play up. Switch it on and the motor seems to struggle to power up. Kind of wurrs up and down. Was thinking it could be the brushes have worn. Tokk to bits and cleaned her up, took a look at motot and brushes, cleaned them too, back together and still them same problem. Help please, hoover is not old but has done some work really don't want to through away something that can be fixed.

Hi.\015\012\015\012after all you have done I would be pretty confident its the motor thats faulty they are expensive to buy so machine is going to be scrap,\015\012\015\012Sorry.\015\012\015\012 ... Vacuums

I have Hoover whisper Cyclonic. I just opend beacuse it was showing Clogged. I removed all dirt etc from the belt and now roller are not moving round and the smell of burning is coming due to rubber not moving on the roller. I looked at the manual which tells me in cased on roller being Jamed if need to use the stich to reset. I looked all over could not find the switch. Can you guys help me please.

... Hoover Sh40080 Zen Whisper Bagless Multi-Cyclonic Canister Vacuum

Runs but doesn't vacuum/****. Sidebrush works fine. Cleaned the roller brushes, and that seemed to confuse the robot and now it keeps going backward a few inches, turning, and then starts going backward again.

Sounds like a sensor problem. pull and clean the front black/white caster assembly and the revealed movement sensor and the 4 cliff sensors along the bottom of the front. Make sure the front caster wheel turns freely. You may have to remove the rolle ... iRobot Roomba 560 Robotic Vacuum

I have Bissell ProHeat 2X 9300-M that I tried to use again today. Is does not dispense solution when turned to Floor Cleaning, when switched to Hose it seems to be working fine. Brushes and suction are working as well. Soap and water containers are full. I took off and replaced tanks, waited to prime the pump multiple times without success. Not sure what is going on.

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

My electrolux ambassador power wand quit working. I replaced the switch that shuts it off when the roller stops, but it wasn't the problem. The on/off switch is fine, the motor is fine. We have traced the problem to the wires inside the canister by opening the inside cover to the bag container. We see the power cords going into the canister but we're not able to get to anything. We can't find any screws to undo that would open it up in order to follow the wires deep into the canister. We've bypa

... Electrolux Vacuums

The brush does not work on my dc15 animal, there is great suction but after about 20 seconds it sounds like something has got blocked in it although nothing is clogged, filters and hoses have all been cleaned but the brush still wont go round

Hi there,Sorry to hear you're having a problem with your DC15. You might find it helpful to visit the Support section of our website and follow these simple steps: ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

I have a dyson - bought it 3 yrs. ago and the roller brush stoped working - doesnt pick up anything. Can you help? The brush doesn't roll or spin. Where can we take it to be fixed and is it under warrenty? THis

Don't worry it's probably just that the belt has broken or stretched. Your actually supposed to change them yearly. So if its been three years thats probably the case. Here is a link to the belt you need and a manual with instrutions: ... Dyson DC07 Bagless Upright Cyclonic Vacuum

G-5 Kirby self-propel works intermitently. The handle must be jiggled until it engages forward. The same for reverse. Once underway it will continue indefinitely until the need to change direction. Jiggle go forward,jiggle go in reverse. It seems as though it helps to push the handle at an angle to the left depressing the switch on the left side at the base of the vacuum head.

Sounds like a loose wire, the wire is connected to the handle, you may be able to fix this yourself but be careful you can void the warranty by doing it your self. (most people make the problem worse) remember your kirby has a lifetime warranty (limi ... Kirby Ultimate G Bagged Upright Vacuum

Hi,dyson dc25 overdrive,my brusher's wont go round,i have cleaned the brusher's and filter,loads of suction.the belt is intact and the roller move's feely by hand,could it be the switch

Hi Stephen,I'm sorry to hear you've had difficulty with your DC25 Overdrive. If the brush bar won't rotate, and you've already checked the cleaner head is free of obstructions, it's likely it just needs resetting.You might like to tak ... Vacuums

When switched on the brushes dont go round and it wont **** up but when i use the handle to clean theres suction there does this model have a belt?

It has a brushroll and transmission i think. turn the top screw and rotate til the end of the nozzle comes off. then pull the brushroll out from each side see if the shafts on the transmission are rotating and also check the inside of the brushrolls ... Dyson Ball DC24 Bagless Upright Vacuum

The roller brush on my Hoover Z700 vacuum no longer runs when you tilt the handle back. I have tested every part that I can: the motor is good; the "magnetic switch" at the pivot point is good; etc. I'm now stumped. Any help or suggestions would be greatly appreciated as I don't want to throw away a $400 vacuum.

Has this not got a rubber belt drive? ... Vacuums

The rotating brush on my Dyson DC25 wont go round - can you help - the machine is new but I don't have the manual?

... Dyson DC25 All Floors Bagless Upright Vacuum


Check your belt or maby something wraped around the end of the roller. ... Dyson Ball DC24 Bagless Upright Vacuum

Sebo X4 when switched on bag full and check brush lights momentarily light up then go off and motor doesnt work

... Sebo X4 Bagged Upright Vacuum

Hi i have got a Dyson dco4 it switches on but the roller doesn't go round. I have checked the belt which has gone so I have no idea what else it could be please could you tell me what else it could be

If the belt is gone, then you need a new belt. Otherwise, ensure floor select switch is set to ON.\015\012\015\012If you don't have a user's manual, you can use the below site to get one free.\015\012 ... Dyson Vacuums

My Dyson dc15 animal roller brush will not turn off when I push the on/off switch....changed the fuse but still will not turn off. Help!

... Dyson DC15 Animal Bagless Upright Cyclonic Vacuum

I have a Hoover Windtunnel Farrington upright model U6431-900 It has worked flawlessly until last week. The roller brush has stopped turning and I believe it is the belt that has broken but I am not sure how to remove the cover to inspect it and replace the belt if that is the problem. Please inform me how to perform the operation and what I should I look for? Is there a site with a diagram on how to replace said parts? Thanks for any and all helpful info that you can supply me with. Larry

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=783264\015\012Generic problem for all Vacuums\015\012I have a Hoover WindTunnel\015\012Posted by ... Vacuums

Panasonic MC-E4013 has lots of **** but won't pick up. Drive belts and brush roller go round OK, Any ideas?

There are a few things to check.\015\012\015\012The Twin Bin model could have clogged filters, So you'll have to depress the button on the top and check that the first top filter isn't clogged, then check the removable black filter and check th ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0990 seconds