Having problems with your Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum ?

Brush bar fails to disengage when handle is upright

\015 My dyson dc 15 ball brush bar fails to disengage when the handle is up and locked,any ideas?\015

Answers :

Repair Help & Product Troubleshooting for Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Brush bar fails to disengage when handle is upright


... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

I have the Eureka 4870 "The Boss" Smart Vac. The beater bar began to turn constantly and can't be shut by moving the Brush Roll Contol to Bare Floor position or the machine to the upright postion. It has also eaten two new belts. A local tech says he has seen this problem whereby the free-wheel assembly that makes contact with the belt to engage the beater bar is misalgned and cannot disengage. It is usually the chassis which would mean replacement of enough parts that would not be worthwhile


... Eureka Smartvac 4870 Bagged Upright Vacuum

Troubleshooting why carpet brush bar won't stop turning when handle is put in upright postion


Hi Janet. Thank you for asking this question. Your vacuum wasn't designed with a brush on/off switch so having the brush continually spin is normal for your vacuum. ... Bissell 3576 CleanView II Bagless Upright Vacuum

Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?


Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson DC04 upright vacuum Brush disengages (ratchet noise etc) when using on clean shortpile carpet. I have checked that brush is clean/clear but it disengages as if jammed every couple of minutes.


I hate to tell you this but that sounds like the clutch is bad ( a common problem ), It is not very easy to replace but you can buy it at sears ( part number ... Vacuums

Brush bar I have a dc28 upright bagless, the brush bar will not turn, I have checked all areas that would have a blockage?


... Dyson DC28 Animal Bagless Upright Vacuum

My Electrolux Regency Series upright vacuum brush motor does not activate. Cleaned the brush and press reset to no avail. Opened handle switch assembly and checked each wire attached to all three switch settings. Tried disassembling brush assembly but could not pry open after removing all screws.


... Electrolux Vacuums

My eureka 5902 4D bagless uprights roller brush stopped spinning. The belt is ok. This model has a sliding switch for roller speed. The brush should spin when you release the handle via the foot release. Bad brush motor or is there a fuse involved?


The same thing happened to me about a year ago with this very model. \015\012The issue on mine was a small, copper-colored metal wheel that attaches to the end of the brush roller. You'll need to remove the top cover (there are several screws). ... Eureka Smartvac 4870 Bagged Upright Vacuum

Beater bar on Dyson upright won't turn when handle is lowered


I have finally fixed my sister's dyson dc 15 beater bar problem. It was just 2 tiny broken wires connect to circuit board lead to the beater bar. The wires broke where they go through the black rubber gommet. You need a torx ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

My beater bar will not spin when the handle is lowered? But there's suction thru the hose when the handles upright


I had the same problem. I read, earlier today, that one of the "problem solvers" called Dyson. Dyson suggested, with the Dyson upright and plugged in, on a carpet, toggle the "bare floor" / "carpet" knob from bare floor to carpet 5 times, then lay ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Vax upright brush bar not turning - VAX Appliances VZL-6012 Bagless Upright Vacuum


... VAX Appliances VZL-6012 Bagless Upright Vacuum

I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.


... Windsor VS14 Versamatic Bagged Upright Vacuum

Hello, we have a DC24, & the brush bar has just failed, resulting in sparks & slight smoking from the brush area. Appreciate any tips / help on this. Regards Rob Littleton


... Dyson Ball DC24 Bagless Upright Vacuum

No suction I have new belts. Everything is clean. No clogs. When I turn it on it smells like rubber , the brush doesnt spin. Everything seems to be free flowing.. Roller brush isnt stuck on the ends. Took off hose to make sure no clogs anywhere. There is not even suction thru the hose with the handle in upright position.


Generally, the problem is that the belt is not running the brushes.  This is caused by one of the following:\015\012\015\012\015\012beater brush is jammed.  This is either an object stuck in the brush or im ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My bissell 9400's brush rollers do not stop turning. When I was using the hose attachment for the stairs the handle was in the upright position and the brushes kept turning. Also water was leaking out of the rear right side onto the the carpet under the machine.


... Bissell 9400 ProHeat Upright Wet/Dry Vacuum

Less than 1 year old Bissell Healthy Home 15 in. 12 amp. Brush shuts off when it is not suppose to if you move handle up and down while in vacuuming mode it engages then disengages. Dosen't matter what height brush is set at.


That machine is made to do that, there is a safety switch in the base of the machine that shuts the brush off when the handle is in the upright position. ... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum

The brushes do not disengage when in upright position


Set the brush control, as needed. The brush control turns the brushbar on the underside of the vacuum on and off. The button is located beside the power button, on the top-front of the vacuum cleaner. Turn on the brush control for cleaning carpet. Tu ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Vax mach 7 upright cleaner does not engage brush bar what so ever


... VAX Appliances VZL-6017 Bagless Upright Vacuum

Dyson DC18 brush beater bar intermittent failure problem.


Take it in to be serviced. It could be a dead motor to bad connection. 5yr warranty will leave you paying nothing. Best Buy or local authorized service center can do it. ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

Motorized brush bar not turning on Dyson Vacuum


Apparent common failure is that either the thin yellow and or blue motor drive wires that run from the LH side of the vacuum where the "control board" is located down into the hinge / ball area become stretched and then fray and eventually break. Ha ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Yellow Dyson handle stuck in down position will not click upright


... Dyson DC07 Bagless Upright Cyclonic Vacuum

Brush bar is not spinning - Dyson Ball DC24 Bagless Upright Vacuum


I would first check your filter as a dirty filter will sometimes produce this probIem. If that doesn't work take a look at the brush bar. I don't believe that these ... Dyson Ball DC24 Bagless Upright Vacuum

Dyson animal loses suction when I let the handle down from the upright position to use, I've cleaned the foam filter, and the plastic filter holder and dried thoroughly, removed and cleared the right side U-bend, and the center, rear U-bend access, also made sure nothing was in the way of the beater bar. Any thoughts? thanks. lorri


Is the noise a loud screaming or a grinding/vibration? The screaming is an air flow problem and you'll want to check your hoses are clear and all the seals are tight. The grinding is an issue with the roller/belt/clutch/motor/housing. From what I'm r ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Dyson dc15 bagless upright. my brush bar is not working but if you use the hose it works .


\015\012http://www.espares.co.uk/datastore/ProductManuals/350256.pdf\015\012\015\012Check the above link to see if it h ... Dyson DC15 Animal Bagless Upright Cyclonic Vacuum

My brush bar is not working - Dyson DC15 Animal Bagless Upright Cyclonic Vacuum


Make sure your clutch is turned on to drive - if ok, take sole plate off to see if the belt is in tact if not, needs new clutch ... Dyson DC15 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0834 seconds