Having problems with your Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum ?

Dc15 power bar problems -intermittently cut out like loose wire??


Answers :

Repair Help & Product Troubleshooting for Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dc15 power bar problems -intermittently cut out like loose wire??


... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Wiring diagram for Model #11635922500 - KENMORE Upright vac I took the cover off of the vacuum to repair the power cord and must have pulled a wire out of its wire nut by the sweeper bar. If I had a diagram it would be no problem to replace. The bad has four short gray wires coming out of it. It is one of the gray wires that has come loose.


... Kenmore Vacuums

HI, I have a Kenmore 25813 and it seems like there is an intermittent short. When I have the extension wand on and the power floor attachment on, when it rotate the wand the light cuts out and so does the power floor attachment, when I twist it back it comes on again. I don't have this problem if I remove the wand and just use the crevice tool with the hose. Any idea where the short might be and can I fix it myself? Thanks. Gary


This is common you may have a short in the contacts from the handle to the wand or a break in the cord that goes into the powerhead ... Kenmore 25812 / 25813 Progressive Bagged Canister Vacuum

Meile Solaris. Power cord connection faulty. Unit powers on/off when cord is being retracted/pulled out. Maybe a break in wire close to connection point in vacuum. Or, the connection point itself is loose? The problem likely resulted from trying to use vacuum at furthest extent of cord.


Cord reel likely needs to be tightened. requirs disassembly and large washers installed to keep reel connections tight. Jim ... Vacuums

The beater bar motor doenst work when i push the bar button the bar button doesnt light up like power button how can i test bar motor or bar switch or what is the common problem wiyh this model I have 2 that dont work the same way


If it do not work ...and you already are on the second one that behaved in the same way it may be a problem with the power in your place and the cause it may be the main fuse...Im not sure where is located in this model but it has to be near the powe ... Vacuums

We have a Kenmore canister vacuum cleaner 25614504. It has in intermittant light and power flicker in the power mate unit as it is moving over the floor. This behavior can be simulated by jiggling the power cord where it eners the power mate. I do not know how to enter the power mate to see if there is a loose wire.


... Kenmore 28614 Canister Vacuum

Again, I have a Bissel Model 3760-4. The same problem as everyone else. The beater bar will not turn. Took apart, nothing. Took to vacuum repair shop and they said it is not getting power to the motor to the beater bar. Seems like a fair number of folks are having this same issue. You would think Bissell would come up with a fix, if nothing else to save their reputation. Thanks Diane


... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

The battery will not charge in the sweeper. I can remove the battery and wire it to the power supply for charging and it will charge up and run the sweeper. So the power supply and the battery are both good. Obviously there is a circuit failure in the on board charging control. Anyone know a fix or a likely faulty component? I had a shark handheld about 8 years ago and it developed the same problem. I examined the little circuit board inside but saw no visible indications that would isolate t


... Euro-Pro Cordless Bagless Upright Sweeper - Blue/Gray

Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n


From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums

My roller bar doesn't seem to be working, but I checked the belt and it appears to be fine, but a bit loose. Is this the problem? dial on front to determine heighth is also very loose and does not click anymore like it did a few months ago. Any help would be appreciated. thx.


If the brush roller stalls when it comes into contact withthe carpet, it might be that the tensioner spring has broken off. This is adesign flaw in the Eureka4870. The symptoms are: 1) brush spins until it contacts the carpet then itstalls, 2) the br ... Eureka Smartvac 4870 Bagged Upright Vacuum

Airvac vm458 had to replace powerhead and telescopic wand last year and problem again loosing power shorting out and isn't working like bought it


... Airvac 14-inch Deluxe Power Brush w/ Headlight VM458

NO POWER My Dyson DCO4 Absolute (purple&lime) won't' switch on. I've checked the plug fuse, wall socket and also filters and hoses on machine all seem fine so think the problem is with the on/off button (maybe loose wire or something) but how do i get to it, is there a special way to remove the green on/off button in order to check the connection? Thankyou in advance for the help i am sure you will be able to provide.


The problem is almost certainly a fatigue break in the flex. These usually happen where the flex enters the handle through the rubber sleeve near the on off switch. You will need to cut about four inches off the wire and reconnect it to the switch. ... Vacuums

Dyson DC05 It is a vaccum cleaner in a perfect condition but recently developed a problem. It sparks and sometimes power goes off while operating. It is clear that the wire is loose but do not know how to open the bracket of the main button on the machine. [email protected]


Hi \015\012try this site http://dysonmanuals.llc.nu/\015\012\015\012It has service manuals for the DC05. ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

The Power carpet sweep attatchment when plugged in runs on and off intermittitly. (Cuts on and off) It has barely been used What is wrong I don't see any loose wires


Try pushing into valve just a little more. If that doesn't solve the problem, it's probably a loose wire in the hose, wands or power nozzle. Could be the circuit breaker in the power nozzle. Contact your installer or a local vacuum cleaner repair cen ... Electrolux Central Vacuum

Have a rainbow e series with 2 speed motor replaced motor with another now after 5 minutes on the vacuum the motor cuts off intermitently like a power surge. all the connections and wires have continuity any ideas???


... Vacuums

Have a Miele S658 Blue Moon that cuts out intermittently, sounds like most of the solutions to similar problems indicate the circuit board has gone bad in the hose mechanism.......can just the circuit board be replaced or does the entire hose have to be replaced?


Probably needs a new hose. ... Vacuums

Aquavac runs for short time then cuts out blowing the RCD . Have rewired mains cable thinking a broken or loose wire... still same problem. Have also noticed that a lot of sparks etc coming from the motor brushes. Vac approx 10-15yrs old.Aquavac is model 6310B


... Vacuums

Oreck Upright Hi Redev, I'm not sure what model I have (about 6 years old...upright, looks like the one in the picture). I changed the belt (which was torn) and then the next time I used it, it cut off on me. Now if won't turn on at all. (I turn the switch on and off and nothing happens as if it is not plugged in but it is!). I noticed at the top where the power cord enters the handle, it is all frayed. Could the electrical wires have detached? Anything you think I should check before taking it


The cord could be bad and will ahve to be replaced. It would have to have a problem inside the handle or down by the motor. ... Oreck XL2600 Vacuum

Beater bar works intermittently


When you push the hose into the tube, there is an acuator that will push the switch so the beater bar will turn. That switch could be just dirty, dust gets in them and they won't always work, the acuator may need to be replaced. Either that or you ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

My electrolux ambassador power wand quit working. I replaced the switch that shuts it off when the roller stops, but it wasn't the problem. The on/off switch is fine, the motor is fine. We have traced the problem to the wires inside the canister by opening the inside cover to the bag container. We see the power cords going into the canister but we're not able to get to anything. We can't find any screws to undo that would open it up in order to follow the wires deep into the canister. We've bypa


... Electrolux Vacuums

Dyson DC18 brush beater bar intermittent failure problem.


Take it in to be serviced. It could be a dead motor to bad connection. 5yr warranty will leave you paying nothing. Best Buy or local authorized service center can do it. ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

Beam powerhead looses power intermittently


... Beam Industries Vacuums

Problem with bosch bsg71360 beater bar going in and out of operation / power


... Bosch BSG71360UC Bagged Canister Vacuum

My Dyson DC 24's beater bar switch didn't actuate and the beater bar didn't turn. When I brought it to a certified serviceman he told me that a wire interferred with the switch and all he had to do was move the wire out of the way of the switch. At the time the machine was under warrantee and it didn't cost me anything. Now however, the machine is out of warrantee and the problem has returned. Does anyone know how to access the switch and move the wire out of the way?


Hi- I had the same experience but it turns out there's a small trip switch if you've taken the brush out to clean it, it needs to be reactivated by pressing the small red button to the right of the brush... took me a year to figure this out! Been mea ... Dyson Ball DC24 Bagless Upright Vacuum

I have a dyson DC28 vacuum and the power button flashes on and off and the beater bar quit turning. I turned it over and found some string caught on the beater bar which I removed, but the beater bar still does'nt turn and the power button still flashes on and off. I hope you can give me a solution to this problem.


I had the same symptom with my wife's DC28. The problem was associated with the cam driven height adjustment mechanism. The beater bar must rock freely up and down when pressing on the tabs that the end cam lobes actuate. On ours I found hair and cru ... Dyson DC28 Animal Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.3169 seconds