Having problems with your Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum ?

Dc15 fuse The roller brushes on my dc15 stopped working..I checked the obvious and then noticed that the 2 amp fuse was blown on the circuit board . I've replaced it with the same type bought from Maplins but it keeps blowing .. I tested the yellow an blue wires leading from the circuit board to the roller brush head and the are in tact and I can run a current through them ... Any thoughts from anyone .? Your help would be. Appreciated thanks Lee


Answers :

Hi Lee,

I'm sorry to hear you're having difficulty with your DC15. If you'd like some help, please give us a call on 0800 298 0298 - we may be able to resolve the issue with some troubleshooting over the phone.

Best wishes,

Jack
Dyson Online Customer Support
http://www.dyson.com
Repair Help & Product Troubleshooting for Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dc15 fuse The roller brushes on my dc15 stopped working..I checked the obvious and then noticed that the 2 amp fuse was blown on the circuit board . I've replaced it with the same type bought from Maplins but it keeps blowing .. I tested the yellow an blue wires leading from the circuit board to the roller brush head and the are in tact and I can run a current through them ... Any thoughts from anyone .? Your help would be. Appreciated thanks Lee


Hi Lee,I'm sorry to hear you're having difficulty with your DC15. If you'd like some help, please give us a call on 0800 298 0298 - we may be able to resolve the issue with some troubleshooting over the phone.Best wishes,Jack ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Cleaning solution does not come out of the rotating cleaning head or the hand-held nozzle the solution pump seems ok but does not run (electrical continuity check between the two leads on the pump show very low resistance so they seem to be intact) - no dirt or blockage is apparent (it is a very simple device with 1 moving part wires to the pump also pass a continuity check THERE IS NO VOLTAGE on the pump leads from the control circuit board when I turn on the "manual" cleaning mode - a


You can contact Bissell directly at the following\015\012\015\012For UK inquiries:\015\012Monday - Thursday 9 am — 5 pm\015\012Friday 9 am — 4 pm\015\012\015\012BISSELL Homecare (Overseas) Inc ... Bissell SpotBot Robotic Wet/Dry Vacuum

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?


... Vacuums

I have replaced the circuit board twice on my hayden 2400 and after working for 24 hours the circuit board then fails, with no signs of it tripping. Everything is wired in correctly the supplier is unsure of the problem but leading up to me replacing the circuit board the machine itself had became intermittent switching on and off while hoovering


Disconnect the wiring from the unit, and go back and plug in your hose. \012\012Get a volt tester and test the voltage coming from the lines at the machine. It should read 0 volts. Check both AC and DC voltage. \012\012Also, c ... Hayden Industries SuperVac 2400 Central System Vacuum

The battery will not charge in the sweeper. I can remove the battery and wire it to the power supply for charging and it will charge up and run the sweeper. So the power supply and the battery are both good. Obviously there is a circuit failure in the on board charging control. Anyone know a fix or a likely faulty component? I had a shark handheld about 8 years ago and it developed the same problem. I examined the little circuit board inside but saw no visible indications that would isolate t


... Euro-Pro Cordless Bagless Upright Sweeper - Blue/Gray

I fear the motor has failed on my Electrolux Oxygen EL6988D. Just six months after the warranty expired, I was vacuuming when it suddenly stopped. There was no blockage in the tube and it wasn't working hard or long . . . it just stopped. I looked around the Internet and it appeared that many similar Electrolux units have a fuse. I hoped my problem might just be a blown fuse, so I took the machine apart. There are two small printed circuit boards, but no fuse. There is an in-line


Hi,\015\012\015\012I don't think you need a new motor, but please stop testing the machine with live power. It's dangerous and unnecessary. Your tests indicate to me that the motor is fine and your thermal-fuse - I think this is wh ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Cleaner stopped working, changed bag still not working. Have checked mains fuse and liittle fuse on printed circuit board. When cleaner is on moving slider to the off positon the LED's glow red for a fraction of a second. Reset button does not feel as though it clicks when pressed, it does not seem to move. Many thanks, Hugh


... Panasonic MC-E583 Bagged Upright Vacuum

Wilson Jones auto 130 Shredder - No power out of power supply, and fuse is good. need circuit board.


... Vacuums

Pulling a 5 amp glass fuse off it's caps on the circuit board


... Hoover Windtunnel Bagged Canister Hose Assembly S3670 59142012

My filter queen majestic quit working. I opened up the unit to see what was wrong and I did not immediately notice anything wrong. Upon furter examination I noticed one of the traces on the printed circuit card was burnt. I used a soldering iron to "bridge the trace and it appeared to fix the problem for a while. Now it has stopped working again, and when I jumper the trace to run the motor it seems to work. Should I just replace the card? Or is there a more serious problem with too much current


I recommend replacing the card. Soldering involves the risk of further damaging the card, so it would be useless anyway. Why waste valuable time?\015\012There is a possibility of the motor overheating, generally due to a blockage in the airfl ... Filter Queen Majestic Canister Vacuum

I have model Model # 11635923500 Sears Kenmore--the unit runs but the brush does not turn--do I need circuit board or wiring ?


... Kenmore Vacuums

My Kenmore 116.25812508 power nozzle motor will not run unless I tilt the handle. I checked the connectivity from the circuit board in the power nozzle base to the telescoping wand with an ohm meter and there is no indication of disconnect.


I have had this vacuum for about 3 yrs and nothing but issues with it. It's been in the shop already once and it needs to go again. No power in the power head. A wheel came off of the powerhead too .. keep snapping it back on but it always comes off. ... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum

My Dyson dc15 animal roller brush will not turn off when I push the on/off switch....changed the fuse but still will not turn off. Help!


... Dyson DC15 Animal Bagless Upright Cyclonic Vacuum

My Dyson DC15 has suddenly become very reluctant to turn left. This is only the case when it is switched on and irrespective of whether the roller brush is running or not. When the cleaner is switched off it behaves as normal as far as steering is concerned.There is no obvious problem with the ball or steering swivel mechanism. Any ideas ?


Hi its Darran at Dyson. Although strange, I believe we have a solution. It sounds as though the cleaner head hose is blocked. When the machine is running the suction will be pulling against the bloskage causingt he hose to contract and p ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Dyson dc15 animal vaccum ,the roller o brush won't run, what can i do, [email protected]


Take it apart and I bet you find a broken belt,replace belt from sweeper shop ,put back together and on your way ... Dyson DC15 Animal Bagless Upright Cyclonic Vacuum

DC15 Vac comes on but the head will nmot come on. Local Vac shop said circuit board was burn up,can I repair myself. where do I get parts


HighnTools had posted this solution - try it.\015\012\015\012I \015\012have finally fixed my sister's dyson dc 15 beater bar problem. It was just 2 tiny broken wires \015\012connect to circuit board lead to the beater bar ... Dyson Ball HEPA Upright Bagless Vacuum - Iron/Satin Yellow

I have a Atwood GC10A-3E water heater. It is not working and the light for the gas side does not work either. I have changed out fuses and had the circuit board tested. Where do I start now?


... Vacuums

HAYDEN 3600 RED LIGHT REMAINS ON THE CIRCUIT BOARD BUT MACHINE RUNS FINE. WHY?


... Hayden Industries SuperVac 6000 Central System Vacuum

I have a Hayden SuperVac 3600, almost 10 years old. The unit still runs, but now when I switch to the power nozzle, it doesn't have power to turn that. I think this happened once before and maybe they replaced a circuit board(?). We took it to a local repairman this time and he says he can fix it temporarily with a new cartridge, but that he won't promise it won't happen again soon.....


The hose has fuseable link inside, generally a 3-7 amp. It is at the wall end underneath the hose cuff. Easy to replace as it crimps in line. If you have a meter you can also test the detachable hose to wall cord for continuity, then check the hose t ... Hayden Industries SuperVac 6000 Central System Vacuum

Miele S318i worked ok till I took it apart to blow really fine ceiling "popcorn" dust that got sucked by the filters. When I plugged back in started for a milli second and quit. At this point I believe the circuit board might be the fault, but I want to test motor before I go and buy the part. Can I simply run 110 to the two moter contacts to bench test? Steve


Yes, you can. ... Miele S318 Bagged Canister Vacuum

I have an Eureka Express canister vacuum - I believe it's model 8284 - that just stopped working. Plug it in, turn it on, and absolutely nothing happens. I took it to the local sew and vac place and they say it's a circuit board that is no longer available. I've looked at all the parts lists and diagrams for that vacuum and I would swear there isn't a circuit board there. (I wouldn't have even thought that in 1989 they would have used circuits.) In any case, I absolutely love this machine a


Given the age of the machine weighed against you fondness for it, unless you can find a fault with either the switch or the cord, there is little else that can be done. With time the electrical lead can break down and one o ... Electrolux Vacuums

Meile vacuum S4210 seems to have a circuit board problem


... Miele S 4210 Bagged Canister Vacuum

Have a Miele S658 Blue Moon that cuts out intermittently, sounds like most of the solutions to similar problems indicate the circuit board has gone bad in the hose mechanism.......can just the circuit board be replaced or does the entire hose have to be replaced?


Probably needs a new hose. ... Vacuums

Model # 5770 the brush motor runs and shuts down after a few seconds...Turn unit off and the brush again will run for a second or two...If I don't turn unit off brush will not start up..Could it be the printed board..the motor brushes..or the wiring that goes from the printed board to the main motor...Thank you


Seems like your unit goes into failsafe because it detects something wrong. Well you should check the brushes and replace them if they are worn out. Also check the wiring for shorts etc, becaue the unit maybe tripping due to an overload. The printed ... Bissell Vacuums

My circuit board has a short on the soldering for the DC rectifier that supplies the carpet cleaning motor. Where can I order a new circuit board. Miele S251i


Just a suggestion, but you could try to re-solder the connection on the board. some of the circuit boards did not have enough solder on the board coming from the factory. That being said, if the component is damaged due to the burning, I ... Miele S251i Plus Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0432 seconds