Having problems with your Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum ?

I have a Dyson DC 15.need to replace the motor cover assy. can't get the part under to pop off . what holds this down.

\015 Broke the motor cover assy. need to take the cover below off also but when remove the screws it won't pop off. what holds it down. any advice on how to remove this part.\015

Answers :

Check the manual for the troubleshooter: Dyson Dc15 Manual
Repair Help & Product Troubleshooting for Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Dyson DC 15.need to replace the motor cover assy. can't get the part under to pop off . what holds this down.

Check the manual for the troubleshooter: Dyson Dc15 Manual ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

The female part of the catch which holds the lid to the accessories compartment closed has broken. This forms part of the handle to the vacuum cleaner.We've had the vacuum for less than a year but cant find the receipt so i think i will just have to pay for the parts. What is the part called that i need or the part number and where can i get it from. Many thanks

Even if you do not have the receipt you are still entitled to one or two year warranty.Since appliance sales are recorded after-sale by manufacturer, you need to contact the manufacturer to validate the warranty and get the replacement. ... Nilfisk Vacuums

I have a Dyson DC-17 and the top of the cyclone has hair and other debris jammed in the ports. It has 6 six screws holding the parts together and I can only get access to 4 of the screws. The bottom piece appears to be removable, but I can't figure out how to remove it without damaging it. If I can get this piece off, then I have access to the other 2 screws. Can you tell me how to remove the bottom piece? Thanks in advance.

The instructions on how to dis-assemble your DC-17 are somewhat lengthy and it is quite helpful to have pictures and videos handy while you are doing it. Normally I would give the instructions here, but due to the amount of info that is necessary to ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My Dyson DC17 has lost suction on the wand and is not picking up dirt as it should. I have taken the small part at bottom of the machine off to see if there is a blockage--none that I can see. The flexible tube on wand is very tight and won't extend very much. Dyson sent me a new cyclonic part in April but the machine still doesn't seem to be working properly. My serial number is 260-us-d11545. Is there somewhere I can take my Dyson to get it fixed. I'm very frustrated with it. Thank you.

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

How do i take the old belt off of my dyson dc 14? cant seem to figure out how to get the roller separated from the machine because i cant get the old belt off.

Go to: Dyson web site or \015\012\015\012 http://www.repairclinic.com/0100_24.asp\015\012\015\012There should be 4 to six screws holding the ... Vacuums

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?

Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I am looking for a specific part for a Nostalgia Electrics RIC-100 portable ice maker and I am finding it very hard to find what I am looking for if I could get some help that would be great. The part I am looking for is the the tray that the ice maker puts the water into and holds to freeze the water to make the ice before it is dumped into the holding tray for the rest of the ice

... Vacuums

On my Eureka Model 1759A (from mid-1980s), the plastic catch that holds the two parts of the metal body together has broken. I would like to replace the part of the catch that attaches to the top (the part with the lip on it), but I can't find the part online ... or even a drawing. Where can I get this part ? ? ? HELP ! ! !

This latch is riveted to the body. If you are lucky you may find an old Eureka warranty/ repair center with one on the shelf, or another canister for parts. That will be your best hope. ... Vacuums

Parts diagram where can i get a parts diagram with a break down of the vacuum, for a dyson dc07 we need to do some work on ours

You can find the exploded views and replacement parts at www.searspartsdirect.com.Go to the link and enter DC07 in the field for Model number. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson DC41 animal complete stuck in upright position - how do I get it down. Have been on hold with Dyson for hours.

The wheels are probably jammed and won't recline. Mine was stuck pretty bad, and after a half hour of trying to figure it out I just picked up the vacuum and slammed the wheels pretty hard, and it came loose. No problem since. Pushing on it hard d ... Dyson Bagless Upright Vacuum DC41 Animal

I was replacing the belt on my Eureka Smartvac 4870 and one of the felt gaskets (or part of it) popped out. I thought I put it in correctly, but the first I used it after replacing the belt, the gasket got mangled by the brush. I'm wondering how important it is to get fixed; is it a part I can pick up anywhere and fix myself? Thanks for the help.

I'm no expert but if you mean the felt on the roller, you have to replace the roller (expensive,esp. for such a minor part). So. I found some felt with adhesive in the craft section at Wal-Mart, trimmed it to fit and done deal. Felt reduces friction. ... Eureka Smartvac 4870 Bagged Upright Vacuum

I have had pfaff 1037 tipmatic machine since 1999. Have been servicing it regularly. Unfortunately, the wheel, which you loosen when filling the bobbin with thread,has broken. I mean the screw which holds the spring has broken. Where can I get a spare part. I asked for the whole machine photograph so that I can tell you exactly which part I mean as unfortunately I do not have a manual for this model.

... Vacuums

My Dyson Animal is not picking up very well in the drive position. With the hose the pick up is still very good. I have had it for 2 yrs now with very little problems. I have cleaned out all areas etc pipes, the brush underneath and cant find any blockages. The noise of the dyson is the same as usual. Could you tell me if there is a part that it sounds like it needs?

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Why does my dyson dc04 work for about 5 mins then cut out the wire on my dyson 04 needs replacin but i cant get the casing off.

This post may be of assistance: http://www.fixya.com/support/t2842769-fix_new_power_cable_dyson_dc07\015\012\015\012Hope it helps ... Dyson DCO7 Animal Bagless Upright Cyclonic Vacuum

Why does my dyson dc04 work for about 5 mins then cut out the wire on my dyson 04 needs replacin but i cant get the casing off. My DC04 cuts out after abou 5 minutes use. I think there may be a thermal cut-out somewhere?

Thermal cut out in coils of motor,you have not been keeping filers clea,I THINK.\015\012motor is avaliable ... Vacuums

How do you put the telescopic wand down? Just got a new dyson 17 and I cant use it cause I cant get the dang wand down..

Make sure your handle is snapped in all the way on to the machine, that will release the clip on the hose to allow for the wand to slide in. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Have Dyson DC 14. When tilt to vacuum, the handle and coiled hose comes away from the unit. The problem started when the little purple ridged curved part on front of vacuum cleaner right below handle came loose and a spring fell out from somewhere--don't know where. I pushed on the purple ridge part and it snapped back on. Now, can't get it loose again, don't know where the spring goes, and handle still comes loose from vacuum.

I'm not positive whether or not this is the wand handle because there are several versions of the DC14. However the device the locks and unlocks the wand in place is pretty similar between all the versions.The first picture is the wand re ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Dyson My dyson stopped working, and now I cant get it to come on at all, I have cleaned everything.

Proberly fauly cable ,switch,or motor req,all parts can be supplied ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I need the catch that holds the accessories lid down on a nilfisk x300 vacuum cleaner. it also forms part of the handle. Where can i get the part and what is it called

Hi there SmartAlec from NelsonVacuums.com.au here. The part for your nilfisk x300 is called an accessory lid lock part number 1470184500. I am a nilfisk dealer so i can hel ... Vacuums

Sweeper belt Hey , i own a fantom thunder sweeper and recently my belt keeps slipping off, i've disassembled it and put it back on a hundred times but it keeps doing it after a few minutes of cleaning , Am i missing a part to hold it on or somthing else wrong i've cleaned it and checked all the ports just cant figure it out and cant find any info online thanks for your time tina

Greetings from GoVacuum.com,Have you replaced the belt with a new one yet? You may want to try replacing the belt, as with flat belts like the Fantom Thunder, they do stretch out 4 -5 inches after time. We in fact recommended replacing ... Fantom Vacums XT450K Upright Vacuum

The valve pipe assembly just popped off our Dyson DC 17. How do I get it back on? I see it appear the arm of the assembly needs to be captured but I can't figure how to get it all lined up without forcing it together.

... Dyson DCO3 Absolute Bagless Upright Cyclonic Vacuum

My Dyson DC17 vacuumn system is stopped up, the clog is in the top part of the vacuum before it drops the dirt into the cylinder. Does the top part of the canister come off so that you can get into the tubes that are clogged.

... Dyson Vacuums

Have a jones 300 machine.. cant get tension parts to work

... Vacuums

The holes on my dyson dc07i are dirty and smell how can i get them clean does the part with root cyclone on it come apart

Hi Susan,\015\012\015\012We'd strongly advise against attempting to disassemble the cyclone pack, as this is likely to snap the internal bin-base release rod, and can also reduce the performance of your machine. \015\012\015\012If you ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Cant get manuel or part #s

Hoover SteamVac F5914-900 Spin Scrub Upright\015\012i just got my machine back after 2 yrs and some parts are missing or need replacement can u help \015\012 \015\012I would ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 1.6187 seconds