Having problems with your Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum ?

Cyclone does not function, no suction at the beater head.

\015 With power on in upright position suction goes to the wand as usual, however when the vacuum goes into the sweep mode there is no action in the cyclone, no suction at the beater bar and back pressure coming from the top of the cyclone housing vent. The beater bar switches on and off OK. and the suction to the wand is OK too.\015\012I have dismantled the cyclone housing and cleaned it out, I have also washed the pre-filter.\302\240\015\012There is still no suction at the beater head and the cyclone has no action.\015\012This problem has just started, until then the cleaner was working fine.\015\012\015

Answers :

Repair Help & Product Troubleshooting for Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Cyclone does not function, no suction at the beater head.


... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

No suction at beater head, no action in the cyclone


... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Help i can get suction from the hose but when i stick it in the back of the carpet head i get no suction and the beater bar will not turn. can you help


... Miele S184 Powerhouse Bagged Upright Vacuum

Beater runs but suction does not - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


The water will not come out of tub when pressing trigger to clean the carpet. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Turbinette head is not functioning the wand itself has suction all apparent dirt has been removed


... Electrolux Vacuums

Beater bar not working. suction not working - Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum


Check for a broken beater brush belt.\015\012Clean the beater brush, clear of all debris and add some WD40 at each end where the rubber holders are. Turn beater brush by hand to work the WD40 into the axle.\015\012Reassemble making sure the belt is ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Powerhead woes Drive belt for power head beater brush on Hoover S3755 keeps jumping off drive motor shaft when vacuuming low pile carpets like oriental rugs unless minimal suction is used. Any tricks to keeping the belt in place other than this?


I've had my Hoover S3755 for about 2 years and loved it, at least until the last couple of months when the "belt slipping off" problem started. I changed the belt and the vacuum would work for a little while then the belt would come off again. I pu ... Hoover S3755 WindTunnel Bagless Canister Vacuum

DC01 Beater Barand cyclone working fine but no suction when using wand ?


They will be a blockage some where in the wand simply take apart tube and clean ... Dyson DC07 Bagless Upright Cyclonic Vacuum

No suction The beater bar is turning but the cyclone is not spinning.


Blocked somewhere check hoses ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson dc14 beater bar is turning but there is no suction


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Miele, Flamenco II. 2 probs. 1. the head brush is not turning when I put it on the floor. If I pick it up to look inside...the brush is spinning fast..I put it down on the floor...the head does not spin at all. 2. The suction power has dropped significantly. The suction used to be so intense, the head would **** itself to my floor and hold on...now, hardly any suction at all.


Sounds like the belt is not on correctly on the beater brush or the belt is worned out now for the suction check filters or bags that need to be empty or clean ... Miele Vacuums

My dyson vacuum cleaner doesn't seem to have the same suction power it used to. I have cleaned out the canister and have taken apart the vacuum head (for cleaning carpets) and it doesn't seem to be blocked but it seems to lose suction by the time it reaches the head. The suction is strong at the end of the hose (where you attach the telescopic attachment with vacuum head) Any ideas? Thanks, Irene


... Vacuums

I caught a hidden shoe lace in my dyson 17 beater head....shut it of quickly....removed the lacing from around the head....loosened the three screws on the botton of the head....cleaned it out from whatever little dust there was....checked the heads belt reset the roller brush into the head...but alas no beater brush action. what to do?(I've had my dyson about5 months....HELP!. thanks, Jan Selman


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Beater brush will not spin and head drops down without using foot release


You didn't provide the model number so couldn't look it uo, but sOme of the progressive uprights have a circuit breaker on, it will trip when something catches on the brush roll, push it to see if it will reset, if there isn't one, get me the model, ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Suction the head clogs up and won't get good suction hair is sticking to head


... Dyson Dc-18 "slim" Upright Model Replacement Motor Filter Part

I have a problem with my EIO Topo 1800 W vacuum the turbo head is not rotating and although it appears to have suction when I go to use without the head it is not suctioning, there is a red light near


... EIO Vacuums

Suction on my dc08 is very poor when turbine head is attached - no problem when not. I have cleaned the brushes an ensured there are no blockages. Why the loss of suction when using turbine head ?


Please go to the web page www.dyson.com and go next http://www.dyson.com/support/help.asp?article=1468&product=DC22-TURBINEHEAD-USand fix it. with commong sense.God bless you ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Beater bar is no longer engaged. Caught a shirt and I pulled it out of the head. After removal, it would no longer spin when I put the vacum in the engage mode. How to reconnect the spinning of the beater bar in the head?


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I can't get the latch that connects to the brush head to engage. Thus the vacumn is extremely hard to push. It has suction, extreme suction. Rollers appear to be dragging. I've tried to remove and reinstall the head several times but cannot seem to get the latch to engage. Please advise.


It sounds like something has come out of it's socket. If the brushroll won't turn rapidly, your clutch is worn out ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Hi my vacuum (Russell Hobss 2200 bagless HEPA) seems to have just enough ( not loads) of suction til it reaches the cleaning head. the head does not appear to be blocked - but there is then almost no suction at all. It also makes loads of noise when on- and an even louder noise when turning off. is it fixable or is it dead? Thanks


Generic problem for all Vacuums\015\012Hi my vacuum (Russell Hobss 2200 Bagless HEPA)\015\012Hi my vacuum (Russell Hobss 2200 Bagless HEPA) seems to have just enough (not loads) of suction til ... Vacuums

I was vacuuming and my electrolux 2100 accidentally suctioned the string attached to a balloon. I turned off the vacuum and unwrapped the string from the head of my vacuum. On the hose i have plenty of suction but the head isn't working. i flipped on and off the emergency shutoff switch but it is not working. what happened? what can i do?


... Electrolux UltraLux 2000 Bagged Canister Vacuum

The floor head is no longer working. The canister works, there is suction, but the floor head is dead. No lights, suction control switch inoperable, no headlight, nothing. It just stopped one day during a vacuum session. Thanks.


Hi poohbear4760...\012Check your wiring going to the vacuum head, some vacuums have a problem with corrosion on the plugs...take your connections loose and lightly sand with fine grit sandpaper the metal ends.\012Plug the wires back toge ... Vacuums

No power to head of Kenmore Progressive canister vac


... Vacuums

No suction Just received my refurb. dyson animal bagless. Finally figured out how to get it all together, turned it on and there is no suction coming up thru the beater bar. The hair is just collecting around the bar and not going up into the canister. It appears all the suction is going thru the open red end of the attachment hose, which has a vented cover piece. Am I missing a piece or is there a switch to turn of the attachment suction?


So the red hose isn't connected to a part on the vaccum so like it is connected to the connester but not to an opening just above the beater bar, this is the only idea i can supply you with. good luck, maybe i got lucky and helped you out. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I had a shoelace get stuck in the beater bar. I turned it off, tipped it over and untangled the shoelace from the beater bar. When I plugged it back in the vacuum ran but the beater bar was not turning and there wasn't any suction. Is there a reset switch for the beater bar? Thank you for your help, Janet


Hi Janet. there is a small reset button on the outside of the head next to the brush that you can push to get it to start spinning again. ... Dyson Ball DC24 Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0442 seconds