Having problems with your Dyson DC15 Animal Bagless Upright Cyclonic Vacuum ?

I need a vacuum brush housing assembly for Dyson DC15 animal. Part of it is broken (plastic).

Answers :

\015\012Try the above link or do a search in google for "Dyson DC15 parts".\015\012Also, try searching in Ebay.\015\012You should have no problem in locating the part.\015\012Lastly, try calling Dyson at 866-MyDyson.\015\012
\015\012Good luck.
Repair Help & Product Troubleshooting for Dyson DC15 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I need a vacuum brush housing assembly for Dyson DC15 animal. Part of it is broken (plastic).

Http://www.espares.co.uk/dyson/dc15/p/1086/716/10\015\012\015\012Try the above link or do a search in google for "Dyson DC15 parts".\015\012Also, tr ... Dyson DC15 Animal Bagless Upright Cyclonic Vacuum

Dyson dc15 animal brush won't turn - Dyson DC15 Animal Bagless Upright Cyclonic Vacuum

Hi there,Your DC15 is equipped with a sensor which shuts off the brushbar if something jams it. Once you've checked the cleaner head for obstructions and removed any threads or hair from the brushbar, you should be able to reset the machine. ... Dyson DC15 Animal Bagless Upright Cyclonic Vacuum

I have a Eureka 4800 series the Boss upright with a bag and Hepa filter. I love it! I was just vacuuming with the hose part and all was well and then suddenly the lower brush came on and a "burning" smell followed. Thought it was the belt so my husband was going to put on the new belt which I had on hand! When he turned it over, the "bar" that holds the belt looks as though it "shot through" the plastic side of the housing on the vacuum. There is melted plastic on the outside of the vacuum and o

I had the same problem. Take out the old belt if possible. Remove the 4 screws inside the filter and the 3 on the front of that housing. pull out the foam around the motor. carefully pull out the suction tube that is press fit against the motor. ... Eureka 4874 Bagged Upright Vacuum

I need a Dyson DC 17 Total Clean exploded parts diagream that shows the switch assembly. There are two small springs and a small plastic part that were loose inside the switch assembly. This caused the vacuum to shut off in the full upright position which is the position you use when using the wand.

I don't have a full diagram for you, but I do have a photo of how they are meant to be assembled: ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

DYSON VACUUM BRUSH WON'T TURN - Dyson DC15 Animal Bagless Upright Cyclonic Vacuum

The problem will most likely be either with the PCB under a panel on the side of the chassis, or the small wires from it that feed the front brush motor. \012\012If you are technically inclined, you can ask for more detail on the repair here: ... Dyson DC15 Animal Bagless Upright Cyclonic Vacuum

Have Electrolux 1590 whole house vac, and can't see how to get brushes out. Leads so short, and don't want to break them trying to free brushes. Do they slide out of plastic housing? My eyes not real good, but it looks like the leads are part of a brass sleeve that slides into the plastic housing. It also looks like the plastic housing may be a snap lock type, but I don't see how to open it.

... Electrolux Vacuums

DC 17 animal, axle roller that acts as a belt tensioner is shot, including the plastic mount that it sets in, (poor design) that wore down when the roller froze up. Where can I get just this part without having to buy the whole brush head assembly? Do they have one that is metal? Not the roller the mount for it>

I've had this stupid problem and my $500 dollar vacume has been broke for months so today after I spent hours on hold at dyson and talking to sears and everybody else under the sun and they say part doesn't exist pretty much, so finally I talk to a d ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Fan housing my sweeper was making noises when you turned the brush so i tore it apart and found that the fan and the casing that covers the fan is broken. I can't find parts cause i don't even know what i am looking for. i believe i have a discontinued vacuum as well

Http://www.hoover.com/ will help you find a local repair shop and they can get almost anything Hoover as long as it isn't a crank model. ... Hoover U5254-900 Vacuum

My brush bar is not working - Dyson DC15 Animal Bagless Upright Cyclonic Vacuum

Make sure your clutch is turned on to drive - if ok, take sole plate off to see if the belt is in tact if not, needs new clutch ... Dyson DC15 Animal Bagless Upright Cyclonic Vacuum

Brush doesnt turn belt isnot broken - Dyson DC28 Animal Bagless Upright Vacuum

Hi there,I'm sorry to hear you're having difficulties with your DC28. It's probably best if you get in touch with us directly so we can resolve this issue for you as quickly as possible.You can call us free on 1866MYDYSON - or if you ... Dyson DC28 Animal Bagless Upright Vacuum

I was in the midst of vacuuming with my Dyson Animal when it stopped working. It smelled as though part of the motor burned up (there was hair and string wrapped around the brush so I stopped to remove it). Any ideas on an easy, quick, and inexpensive fix? Thank you!

Hi there,For guidance on clearing any remaining threads or hair from around the brushbar and resetting the machine, please follow the steps shown in the video below. Please note, the brushbar will never rotate when your machine is upright, so ... Vacuums

Brushes will not spin -- broken part

Did deeper, I finally just fixed mine today, I thought the same thing about it not wanting to come apart, but try one more time, and when your almost done, look underneath there is a long plastic piece with two screws almost side by side towards the ... Hoover F7222-900 SteamVac Upright Vacuum

I'm using Miele Medivac vacuum and I just sucked in a small plastic eye drop container by accident(I sometimes take off the brush part to **** in 'small enough' articles). And it is jammed in the part where the plastic hose connector bends. I think I can take it out if I can just disconnect the long necked plastic hose connector that connects the metal wand part and the hose part. Is it designed to be disconnected or should I not even try it?

I love the fact that the filter bleeped out s.u.c.k ha ha! ... Vacuums

My Dyson Animal has good suction and works fine for actually picking up dirt, but when I use the vacuum with the roller, I hear a grinding/rumbling noise. Its only when I use the vacuum with the brush rotating. It does not happen hen I shut the roller brush off. The belt is fine. I cannot figure out what is wrong as there are no clogs, debris, or foreign objects stuck in the brush or in the belt. The noise seems to be the only issue. The vacuum picks up fine. It just doesn't sound right a

Trace the path of the suction into the tank and see if there is anything loose or ingested.\015\012Also, remove the brush and clean as best you can. Perhaps there is something caught in it. Lubricate where it makes sense with some WD40. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I'm using a Eureka maxima 12 amp vacuum and where the hose is connected to the vacuum by a screw that part is broken where do I find a replacement hose that includes the clear plastic part that I can attatch to the vacuum?

... Eureka 4700A Maxima Bagless Upright Vacuum

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help

The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I was vacuuming with the Dyson DC 17 and sucked up a berber carpet string by accident and after cutting and pulling it all out of the bottom brush part, the brush no longer spins but the suction part works. What do I do?

The belt could be snapped. If this model has a brush protected belt then it has to be repaired by a service call. If however you can get to the brush roll belt by removing the bottom sole plate (turning over the vacuum so that you're looking at the b ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have Dyson DC15 ,Brush not working - Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

The foot pedal on my Kenmore upright vacuum cleaner has broken three times. The vacuum model number is 116.33923 and the Sear's part number is 8174906. Does Sears make this part in metal instead of plastic? It is becoming expensive to keep replacing this piece when it costs around $20 each time (including shipping) Thank you for your time. Jerry DeWulf

... Vacuums

The Neutral/drive pedal fell off our Kirby G5 vacuum cleaner. I opened up the area housing its connection to the transmission and a couple of the parts were just laying inside. I need a diagram for assembling it and see if I am missing any parts. It was a refurbished machine and a paperclip fell out of the housing when I opened it. Can you help me?

Hi,In the below links you have the parts diagram as you asked will this helps you?If not let me know i will help you more.http://www.fiorijanitorial.com/s-19-kirby-parts-and-bags-generation-3456.aspxhttp://www.vacu ... Kirby G5 Bagged Upright Vacuum

VACUUM REPAIR I have a Hoover Savvy upright, windtunnel, bag/bagless vacuum (model U8150-900). The Handle Release Foot Pedal - Part #38434026 broke soon after purchase but I finally found a source to replace this item. The problem is that now that I have the repair part I cannot figure out how to remove the old pedal and install the new one. The housing appears to be one piece of solid plastic. Any ideas, PLEASE! Peter

There are 2 tabs that stick out on the release, they fit in slots, so from the top look down and you can see them, using a flatblade screwdriver that will fit in there, push the side in to release it, which isn't easy, but it can be done. When you g ... Vacuums

Dyson Animal handheld brush not turning - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Hi its Darran at Dyson.We would recommend checking it for a blockage and a removing any hair or fibres from the brush bar. As the brush bar relies on the suction power of your machine, it would be worth cleaning the filter and ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have Optima, 12amp Eureka vacuum, Model 431, AXZ type and the extension hose for cleaning corners and edges --the plastic part that the attachments fit into has a piece broken off and tools don;t fit anymore. It looks like the hose attachment can be replaced--can it be and if so--where can I get a new hose attachment. It seems it is cheaply made of plastic and really shouldn't have broken a piece off.

... Eureka 431A Optima Bagless Upright Vacuum

U-Shaped piece I was in the hospital for a couple of nights and my 80 year old mother decided to go to my house and vacuum my house. When I went to get it out to vacuum the other night the u shaped part fell off. I guess my mom had somehow knocked it off. Now I cannot figure out where it goes. It is a plastic U-shaped piece. Can you help me? I sat for a hour trying to figure out where it goes.

It attaches at the bottom of the hose and goes into the bottom of the valve. Located on the back bottom of the unit. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I was told that the brush assembly(black plastic holders)should be inverted/fliped over when doing maintenance on my orickXL vacuume cleaner? So not to wear out the brush assembly is this correct?

You adjust it to adapt to the wear of your brush. they will make your brush higher or lower since the hole is offset. if you were to install a new brush you would want it as far away from the carpet as possible and vise versa. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1426 seconds