Having problems with your Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum ?

My DC16 will start and then stop. I have to take

\015 My DC16 will start and then stop. I have to take my finger off the trigger and start it again...this happens all the time. I have washed out the filters and checked the intakes...nothing will fix it.\015

Answers :

My DC16 also had charging problems. I called Dyson and they sent a new charger. The old charger only produced 23.6 volts DC, not the rated 28 volts DC. The new charger has a thicker round wire and produces 28.1 volts DC. Put a volt meter on your charger terminals and see if it is producing enough voltage to fully charge the battery, 28 volt DC. If not you need a new charger.
Repair Help & Product Troubleshooting for Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My DC16 will start and then stop. I have to take

My DC16 also had charging problems. I called Dyson and they sent a new charger. The old charger only produced 23.6 volts DC, not the rated 28 volts DC. The new charger has a thicker round wire and produces 28.1 volts DC. Put a volt meter on your char ... Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum

Simplicity vacuum My vacuum just cut off and now it wont start. I pressed there restart button but nothing happens I have 2 fairly old Industrial hitachi dry vacuum in my workshop both 110v and both wont start. Both i was told were manufactured in Italy and both have a manual and auto switch. It has a black top, takes an orange paper filter inside and its bin is dark blue. Sorry i've forgotton the model number. I've inspected the wiring but it's fine, could it be the motor and how do i gain acc

Just take it in to your vacuum store. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Bissell powersteamer powerbrush starts up and then i pull the triger and water starts then stops. i cleaned the bottom of the tank by taking it apart and even had a different tank and both of them did not work. changed belts???

Tried to find out about this problem, and ran across this recall on the net:\015\012http://www.consumeraffairs.com/recalls04/2005/bissell.html ... Bissell Powersteamer 1694 Upright Vacuum

I have had 226R 20 years. Don't use it much. I have learned to pull slack out of top thread to start so I do that. However, sometimes, as today, it will wind the thread around the bobbin holder and I have to take time to ge it all out clean it up. Is something out of adjustment or what. Sometimes it will sew OK then all of a suden it will start to wind the thread around the bobbin holder again. So I'm confused. Do you have any ideas. Thanks

Hi wwilson63,What make is that 226R?The problem is that the thread is not threaded correctly. You must be very careful and follow directions explicitly.Once you think you have it threaded correctly, sew a few stitches and see ... Vacuums

Brush turning slowly while shampooing. It starts out fast, but after a minute or 2 the brush is not spinning very fast. I have powered it off and let it cool down. I just started out so I can't believe the engine is over heating, just doing 2 rooms, can't even get through the first room. If I take the brush attachment off, then put it back on and then turn it on, it spins fast, but after a a few minutes, it's spinning softly/slowly again. Kirby diamond edition

Track not set properly in grooves\015\012there could be a clog or the cleaner has built in feature to slow down heads for better cleaning this does it on its own ... Vacuums

Lately we've been having plumbing problems to where our washing machine floods up our bath tub and toilet. And it happens while we have the washing machine on of course. Another problem is that whenever we are taking a shower our tub starts to clog up and water starts pouring out from the bottom of our toilet. We had a plumber come by to root out our pipes just last week and it was fine for about 3 days. And now the problem is back and driving me crazy. WHAT IS WRONG AND HOW CAN I FIX IT??

Possible tree roots best thing is to hire a plumber with a camera snake ... M&S Systems AirVac AVP1200 Platinum Series Central Vac - 12,000 sq ft Bagged Central System Vacuum

My Hoover Whisper Cyclonic is collecting the dirt but not taking it into the cylinder. The brushes were at one point starting and stoping due to the belt periodically turning,now the brushes are turning and the dirt just collects and I'm starting to smell a an oder like rubber burning.I've taken it apart and tried to make sure the is no clog. The one hose that I can't check is in the back right base, above and left of the right back wheel.

... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

It starting to put out a hot type smell. I have tried cleaning the filters real well and even tried to see if there was problem with the ozone filter. We have checked and could not find a jam. I know the hose has excellent suction. The vacumn works but the intelliclean sensors will not. It only takes about 15 seconds or so for the odor to start. Then it gets real strong and it makes my eyes water

Hi,The hot smell could be from the belt or the motor. Turn it on for a moment, turn it off, then flip it on its side and smell the belt that drives the brush. If that is where the smell is coming from, then your belt is burning up. ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum


Go to http://content.dyson.com/support/and see the complete information for troubleshooting, manual, videosetc.and fix it.God bless you ... Dyson DC16 Bagless Handheld Cyclonic Vacuum

Dirty filter caused vacuum to swtich off mid-use. Filter's cleaned, but machne won't start again. Is there reset switch or do I need to take it in to get fixed?

... Westinghouse WST1551 Wired Deluxe Upright Vacuum

My Kirby G6 light is not turning on when I start the machine. I took off the front piece and removed a lot of hair from the roller and interior. Since I did that, the belt keeps coming off (even though it is fairly new). Is that the reason the light won't turn on? Is there any advice you can give me before I take it in?

The light indicates that the brushroll is spinning. If it isn't coming on, the power nozzle may have been reinstalled incorrectly. Take the nozzle off and then use my step-by-step guide to reinstall it. I expect that it will take care of the problem. ... Kirby Vacuums

My Bissell spot bot stopped sucking the solution from the container. When we had the problem before we just reseated the container and it started releasing the water/solution. There is a funk little hole that takes water from the container and it seems to move around a bit. We own 3 spot bots, and have had trouble with all of them.

... Bissell 12005 Spot Bot Handheld Vacuum

We have the bissell quicksteamer and as I was shampooing I began to notice something burning so I unplugged our machine immediately; then my mom and I started cleaning all the filters assuming that could be the source of our problem and yes it was a little dirty but I suspected that it would take more thant that to cause our machine to somke soI turned it upside down and noticed there is a cable of copper threads that appear to have some type of rubber or plastic insulation tubing around it but

Was the exposed copper wiring on the electrical cord? If is then replace the cord. The main problem with this model is that Bissell obsoleted it as well as parts for it. But if all you need is a cord, you should be able to get one from a repair shop. ... Bissell 1960-3 QuickSteamer Plus Upright Vacuum

Does the dyson 07 take about 15 seconds to start suction after it is turn on?

No should start instantly.Check for blockages and check the filters if its taking that long! ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My mother purchased a replacement hose assembly for a Bissell ProHeat 2X and the part was shipped without any instructions... While I am pretty handy, my issue is with the supply tube, and I cant figure out how to accomplish the replacement, and as its not MY vacuum, Im hesitant to start taking things apart.I just need instructions to replace the entire hose assembly.

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Dyson vacuum beater bar takes a while to start working.

Hi there, \015\012SmartAlec from NelsonVacuums.com.au here. If there are no bad sounds or smells when you are engaging the bar then it is a sign that your belts are s ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My electrolux oxygen canister cuts on and off. I have to open and close the vacuum, or take the base of the hose off and then re-insert. I have to do all these things before it will start up again. I sometimes shake the hose around, then it will come back on. If I try to dust with the dust brush (like a lamp shade or shelf) and the suction pulls against the object, the vacuum goes off for awhile. Sometimes I'll have to reset the vacuum by unplugging the electric cord. I never get to finis

Maybe you should have taken it back to that shop, it appartently isn't fixed. I would have replace that board, don't believe in modifing, you usually end up with other problems, like you have. One thing to check is maybe you have a partial clog in ... Vacuums

How to take off motor on the dirt devil kurv, my start button is stuck

... Dirt Devil KURV Hand Vacuum Champagne Vacuum

I bought A chef's mark digital slow cooker made by select brand. I have only used it 3 times since I bought in in late jan or early feb 2010.THE first time I used it the rubber leg fell off. Then the handle started breaking off A little piece at A time it now only have half A handle on one side. I take care of my products because they cost to much and the price to mail are outragious. What can I do

... Vacuums

Water leaking When I fill the canister portion with hot water and put it in my machine it immediately begins to leak out the bottom. It has just started doing this. Do I need to take it in for repair?

The water tanks on this unit have had a very bad history of leaks. Most of the repair people had never heard of this unit, but one did, and had a spare set of tanks. If the unit is still under warranty, it is worth your while to get a replacement u ... Eureka Atlantis 2595A Upright Wet/Dry Vacuum

Have dc05 how do you take it apart won't start

The site www.dysonmedic.com is very good.\015\012\015\012If you follow the link below, it will take you to photo article on how to change the motor - this will show y ... Dyson DC05 Bagless Canister Cyclonic Vacuum

Lost suction my DCO7 lost suction in the hose I started taking it apart and cleaning it and looking for clogs (probably more than I should have) and when I put it back together it has awesome suction in the hose but no suction in the base. It just pulls the pine needles up (christmas tree) but they never appear in the "bag" compartment and when I look they are just all gathered in a clump in the bottom by the brush.

Hi.\015\012\015\012Remove the sole plate turn the 3 plastic screws to unlock & lift off.\015\012\015\012Now remove the blockages that have accumilated from the oppening of short clear hose.\015\012Check you can turn ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Hi. I have Dyson dc08 hepq+. Thet problem is its not having suction .I checked inside the pipe and foot , ery thing is fine. And if i take the whole dirtbin out ...machine workes fine. when i put ery thing back ....as soon as i start it , after 2 second machine change its voice...and loos suction. I think its just happen because ...the saftey yellow valve inside the machine turns up because the dirt drum is blocked inside some where. Any suggstion ...what can i do with it. I m tahnkful in avance

Hi its Darran at Dyson.From your description of the problem, it sounds as though the bin inner is missing. To confirm this, if you remove the cyclone and bin from the machine, then separate the 2 pieces as if you were going to empty it, w ... Dyson DC08 Hepa Allergy Bagless Canister Cyclonic Vacuum

My Jacuzzi Tracker 4x just "stopped"..there is a nice strong flow of water going into it, but the wheels just aren't turning. I've tried the following to no avail: 1. blocked suction for a few seconds underwater with my hand (this has worked in past) 2. try to move front wheels back and forth (but they won't budge...back wheels do move on track though) Should I start taking it apart?

... Vacuums

The vacuum shuts off by itself and then sometimes takes a while to start again after several attempts, progressive canister type 25914507

Sounds like your motor is cutting out from a thermal fuse. this means that when it overheats it will turn off and then will reset, allowing you to operate the vac. The problem could be a result of poor air flow...check the filiters and hose path for ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.2131 seconds